Question about Cars & Trucks

Open Question

How to replace the fuel pump 1994 Isuzu pickup

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Where is slave cylinder for clutch on 1994 Isuzu pickup 2.3 litre

To determine which type of clutch you have, servo hydraulic or cable.
Look down past the engine bell housing and determine the existance of a hydraulic clutch slave cylinder.(a piece of casting with a rod facing towards the rear of the vehicle pocket into a bracket protruding out of the gearbox bell housing. As well as a pipe and bleed nipple to be crude)
(which I believe you have).The hydraulic fluid for this unit is sourced from the brake master cylinder reservoir via a sneaky pipe partially obscured to the clutch master cylinder on the internal firewall.If you have no clutch slave cylinder near the bell housing there would be an obvious bounden cable running from the firewall down to the outer of which will be stopped at a bracket hanging off the engine.The inner will continue to a bracket protruding from the gearbox bell housing.

Posted on Mar 05, 2009

  • 1596 Answers

SOURCE: I need to replace the fuel pump in my 1985 Chevy S10 Pickup.

EXACT PROCEDURE ! Please Rate Me Fairly for this!! Thank you And Good Luck !!


ELECTRIC PUMP

REMOVAL

  1. Before servicing the fuel pump the fuel system pressure must be relieved. See: Fuel Pressure Release
  2. Disconnect the negative battery cable.
  3. Raise the car on a hoist.
  4. Remove the fuel tank. See Fuel Tank / Service and Repair.
  5. Remove the fuel tank sending unit and pump assembly by turning the cam lock ring counterclockwise. Lift assembly from the fuel tank.
  6. Pull the fuel pump up into the attaching hose while pulling outward away from the bottom support. Take care to prevent damage to the rubber insulator and strainer during removal. After the pump assembly is clear of the bottom support, pull the pump assembly out of the rubber connector for removal. NOTE: Inspect the fuel pump attaching hose for any signs of deterioration. Also check the rubber sound insulator at the bottom of the pump. Replace damaged or deteriorated parts.
INSTALLATION
  1. Push the fuel pump assembly into the attaching hose.
  2. Position the fuel tank sending unit and pump assembly into the fuel tank. Use a new "O" ring seal. NOTE: Care should be taken not to fold over or twist the strainer when installing the sending unit as this will restrict the flow of fuel. Also, verify that the strainer does not block the full travel of the float arm.
  3. Install cam lock over the assembly and lock by turning clockwise.
  4. Reinstall fuel tank.
MECHANICAL PUMP

REMOVAL and INSTALLATION

NOTE: To ease pump installation, rotate the camshaft so the camshaft eccentric is out of the way of the fuel pump rocker arm.

  1. Disconnect fuel lines from fuel pump.
  2. Remove fuel pump mounting bolts and the fuel pump.
  3. Remove all gasket material from the pump and block gasket surfaces. Apply sealer to both sides of new gasket.
  4. Position gasket on pump flange and hold pump in position against its mounting surface. Make sure rocker arm is riding on camshaft eccentric.
  5. Press pump tight against its mounting. Install retaining screws and tighten them alternately.
  6. Connect fuel lines. Then operate engine and check for leaks.

Posted on Mar 22, 2009

  • 1861 Answers

SOURCE: 1994 toyota sr5 pickup not starting due to no

Look in the fuse box under the hood. Look to see if the 15 amp EFI fuse is blown. If so, you may have a short circuit at the fuel pump wiring under the bed/on top of the tank. If it is not blown, you may have an open circuit on the same wire; this is a very common issue to the 94 trucks.

Posted on Jul 17, 2009

  • 701 Answers

SOURCE: location of fuel pump relay on 1994 s-10 pickup

Hello skaterkid012: My name is Roger and I will help you. You will find the fuel pump relay located under the center the center of the dash in the convenience center. Should you need further help please just ask. Please rate the answer you received.This way we know the answer was helpful. Thank You for using Fix Ya. Roger.980ba70.jpg

Posted on Sep 26, 2009

  • 2 Answers

SOURCE: replaced fuel pump in isuzu rodeo 95 and it won't start

hello
did you solve this problem? I am replacing the fuel pump on my 95 Rodeo tomorrow.
Thanks

Posted on Apr 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I change my fuel pump , filter on my 1994 Isuzu pickup truck ,4cylinder 2.3 liters and I have no gas a carburetor. I try using starting fuel to start it and its starts and dies . How can I fix it?


Take the gas line off at carb, and crank the engine over. If gas does not start spurting out from the gas line, then the new pump is not working right. Maybe the pump arm is not situated right against the eccentric gear that makes the pump work. You would need to re-situate the fuel pump.

May 10, 2016 | Isuzu Cars & Trucks

1 Answer

Why does my 1994 Isuzu pickup truck 2.3 liters 4 cylinder is not receiving fuel to carb after installing a new fuel pump??


Can you hear the pump run? Is there any chance that it wasn't plugged back, properly? Also if the filter and I was removed. Could it be backwards?

May 10, 2016 | Isuzu Cars & Trucks

1 Answer

How do I get fuel from fuel pump to carb on a 1994 Isuzu pickup truck after I install a new few pump?


The fuel pump is electric? It should feed the carb with a few pushes on the accelerator peddle with the key on. If not, try "starting fluid" available at local auto parts store. Comes in a spray can and you spray it into the top of the carb while someone else turns the key and pumps the gas peddle.

Apr 26, 2016 | Isuzu Cars & Trucks

1 Answer

1994 Isuzu Pickup 2.3L carbureted motor with mechanical fuel pump lost prime


If it were just that you would be ok once the engine started.
You might have a float problem with the carb. or something in the tank.
Are you sure the pump is not pumping ?

Jun 28, 2012 | Isuzu Pickup Cars & Trucks

2 Answers

Not getting any power to the fuel pump


Check the Fuel pump relay switch

Jan 27, 2011 | 1994 Isuzu Pickup

1 Answer

I have a 1994 Isuzu Pickup 2.3L


Take out the fuel-pump and examine it for short-circuit. If its exterior is rusty, you might try another fuel-pump.
Check for vacum leak around the throttle-body, and the vacum hoses.
Spray some choke cleaner inside the throttle body, and the exterior.
Check and replace the PCV valve if defective.
Remove and clean out the EGR valve. Make sure its connections are tight and not leaking.
Try swapping another control-module.

Make sure your truck has no anti-theft device installed without you being aware.

Dec 17, 2009 | 1994 Isuzu Pickup

2 Answers

How do you change the fuell pump on a 1994 Isuzu Pickup truck?


The fuel pump is mounted to the underside of the intake manifold where it bolts onto the cylinder head (real pain to get to). If you remove the fuel pump there is a plastic spacer between the pump and the manifold (DO NOT LOOSE IT).
Good luck
MIKESTA

Jul 13, 2009 | 1994 Isuzu Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...