Question about Mitsubishi Pickup

Open Question

Reset limp mode

Saturday gave the triton 2.5 an engine clean with a compressor spray gun. Sunday went for a drive, triton engine light come on and she went into limp mode. where to start looking for the problem?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 580 Answers

SOURCE: BMW (e39 1999) eml and asc lights and in limp mode

Check the ABS brake sensors in your wheels, if they are not functioning properly. It will trigger the computer to engage the ASC auto stability control light as the asc uses the brakes to assist in control. I will also engage the EML engine management light to slow the rev point to limp mode

Posted on Aug 23, 2009

  • 14036 Answers

SOURCE: engine managment light comes on and goes into limp

MOST TIME LIMP MODE MEAN ECM FAILING IF YOU CANT ERASE OLD CODE AND REPROGRAM ECM. AND IT CANT RELEARN NEW PART ECM HAS A MEMORY FAULT.

Posted on Jun 27, 2011

  • 1 Answer

SOURCE: My Hyundai Grandeur XG30 has

replace both input and output speed sensors and she will run like a beauty

Posted on Nov 18, 2011

matt_sams
  • 124 Answers

SOURCE: mondeo engine goes into limp mode when driving

I would check and change fuel filter first.

Posted on Jun 08, 2012

  • 3 Answers

SOURCE: 1999 concorde. in limp mode with check engine

Change both sensors at the same time. Once you change that, have the computers reset. That will take your transmission out of safe mode. But speedometer must work to keep transmission out of safe mode. Input sensor lets transmission know when to change gears. If it gets no signal at all it changes to safe mode 1st and 2nd gear. Which runs your RPMs really high. If you drove a lot with it likes this. Once sensors are changed. Check transmission fluid while its running and on flat ground, make sure you use the right transmission fluid, wrong one could cost you a transmission.

Posted on Oct 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car on limp mode- changed AC compressor-water pump-harmonica balancer- pulliies belt air cleaners-battery was flat all good now went good on test drive next day it went to limp mode after short drive now...


use a fault scanner to reset the CPU program If everything is good it should work . if not the fault codes will reappear and you will know what to fix.

Dec 25, 2014 | AC Cars & Trucks

1 Answer

1993 Isuzu NPR when taking off transmission shifts good but after bout 1/4 mile downshifts out of overdrive and will not shift into of again until it sits and cools for a little while


Many of todays cars have a mode called Limp Mode. The Motor and Computer talk to each other and if faults are found? The Limp Mode (( Short for Limp on home mode )) will be set in the Computer. Go to your local Auto Zone and ask them to Scan the OBD 2 fault codes with their reader. Or pay the dealer. It may be something really simple. My Check Engine light was on the other day because the Gas Cap was loose. This Scanner told us the problem and we tightened the Gas Cap. After 3 times driving the car with it tight .... The Check Engine light went off.

Aug 17, 2014 | Cars & Trucks

1 Answer

Oil light is on and engine in limp mode


check the oil level in the sump, coolant level, coolant temperature (overheating), transmission oil level if auto. The limp mode is energised by any number of sensors that register a fault that is detrimental to the engine/ gear box. Run the fault codes and repair any faulty units . Reset the CPU with a scanner .

Jul 02, 2014 | 2005 Holden Rodeo

1 Answer

2007 Mitsubishi Glxr Triton running on limp mode after sucking in smoke


P0191 fuel rail pressure sensor circit
p0652 sensor1 low supply voltage
there first one is possibly a loose connection.
The second is the code for bad gas pedal sensor
replace sensor for gas pedal /check connector at the fuel pressure regulator

Feb 01, 2014 | Cars & Trucks

1 Answer

My 2006 Toyota Tundra's check engine light came on, the engine code gave me p2440. The truck had to power on the highway, reseting the computer fixed the problem temporarily, what should I do?


run the fault codes to find why the engine went into limp mode . to reset the light is not the answer as it may be over heating or low oil pressure all of which is bad news for the engine.

Oct 08, 2013 | Toyota Cars & Trucks

1 Answer

I have a 2000 S Type with 100,000 miles that I bought about 4 months ago. Within 2 weeks of purchase, the Failsafe engine light kicked in and went straigh into "limp home mode" I did some...


the best thing to do is to have the car scaned with the diagnostic computer to see what fault codes are stored.
acording to the fault code you'll be able to work out what's wrong with it.
I'm sorry i ca't be anymore helpfull.

Jul 25, 2011 | 2000 Jaguar S-Type

1 Answer

Electronic throttle control symbol illuminated this morning and the engine went to a limp-home, what does it mean, and is it costly? Driving to the train station in Atlanta this morning the symbol came on...


I would not recommend any trip until the car is repaired. The symbol in the dash means the car was in limp mode. It could be caused by the T/P sensor, this is the most likelt problem.

Oct 23, 2009 | 2004 Lincoln LS

2 Answers

1995 Chevy k1500 Transmission Problems


If check engine light is on ,remove battery cable, you have an electrical problem, maybe fuse?

Mar 16, 2009 | 1995 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...