Question about 2003 Volkswagen Jetta TDI

1 Answer

No power to wheels after instalation of new clutch and transmission

Put new clutch and transmission in car but no power to wheels. checked clutch and transmission, both working properly. could it be the cv shafts.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 34 Answers

Could be input shaft or tail shaft of transmission broke.

Posted on Nov 18, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 14 Answers

SOURCE: cant get my 95 cabrio's transmission out

Turn the transmission clock wise to posiotion the disfferencial at 10 o'clock. Pull it away from the engine as you lift the tail. You could take it out on your own, but need the help of another to put it on if you are not in a shop with all the tool. Hope this helps.

Posted on Dec 16, 2008

  • 61 Answers

SOURCE: 1995 VW Cabrio Speedometer not working

Speed sensor should be in the front driver's side wheel well. My guess is it was disconnected while you were working.

Posted on Apr 17, 2009

  • 1206 Answers

SOURCE: 2002 jetta tdi with manual transmission, front end shakes

check for bent axle or missing vibration rubber damper that is usually on the axle.

Posted on Feb 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Firebird clutch periodically goes bang when engaging


If you have a cable operated clutch then check the engine mounts especially the rear mount or reaction rod on a transverse transmission.. If you had a clutch problem it would be there all the time and the indications are that it would be slipping , shuddering , grabbing and generally be a pain in traffic. I would be looking for a reason to allow the engine /transmission to get out of alignment and cause binding of the drive shafts . If front wheel drive check cv joints and suspension points . If rear wheel drive check for problems in the slip joint or "u" joints.

May 14, 2014 | 2002 Pontiac Firebird

1 Answer

Transmission removal


You must remove completely the clutch lever at the transmission pressure plate bearing to disangage, to install you need a new bearing (when you install it, it came in 2 part when install it snap togetter) can not go down put it beside on the frame

Apr 10, 2014 | 2006 Hyundai Elantra

1 Answer

DYI Clutch change, now transmission won't fit with the new clutch kit??


While its seams you don't see where you have to make caution,
So Now !Put back fry-wheel back on crankshaft then just check two thinks ......Check 1: see clutch plate there is center gropes on it so Mach on gear shaft center gropes.(I mean just put clutch plate in to transmission shaft & check if it`s center gropes are same match) If yes then pull back clutch plat & then refit under pressure plate on fly-wheel. Now come to Check 2 ! Mow when you fit it you must do centering of clutch plat to fix on gear shaft, So How you can do ?
There is two ways 1 is you have same shaft designed road or wood piece which help to center it!
While 2 ways is take big screw driver & put in the hole & do centering by looking it where center come just tight pressure plat bolts to hold the center .
So when you did like this you ll fix transmission (gear box) easily in a mints ....Just simple like this.
So best of luck & if you have any problem just mail me tallnsmartman@yahoo.com......

Nov 25, 2013 | Cars & Trucks

2 Answers

DOES THE 5 SPEED TRANS NEED TO COME OUT ALL THE WAY WHEN PUTTING IN A NEW CLUTCH 22R TWO WHEEL DRIVE


yes because the cluch and pressure plate need to come off around the gear that fits into the transmission.

Feb 02, 2011 | 1991 Toyota Pickup

2 Answers

Shifter works when car is off, start car and then shifter won't go in gear. if i start vehicle in first with clutch pedal to floor, car starts going forward. mazda miata mx-5 just put new slave cylinder in...


The one item I would suspect is the through-out-bearing not completely disengaging the pressure plate from the fly wheel. If the vehicle is in neutral and you slowly depress the clutch and release it do hear a singing or whining sound? Since you cannot adjust the clutch any more the through-out-bearing is the component which moves the pressure plate from the fly wheel to stop the power from the engine to the transmission. It is difficult to shift when the engine is on because the fly wheel is still engaged and powering your transmission.

Aug 06, 2010 | 1997 Mazda MX-5 Miata

1 Answer

Replacing the clutch on a 1998 Saturn SL1 we encountered a problem after installation, The clutch would not disengage. The hydraulic clutch system and slave cylinder seemed to be working fine, we even...


It is very difficult for you to disengage the clutch by hand or with any leverage you can get outside the transmission. There is over 200 lbs of force clamping on the clutch disc.

If you replaced the clutch and took the slave cylinder out of the transmission without putting a brick under the clutch pedal or disconnecting the pivot arm from the pedal then you ruined the hydraulics. Buy a new PRE-BLED system from a local auto store. Generally this is the problem.

Either that or the clutch fork is bent or you installed the throwout bearing backwards (or simply fell off the fork which is not all that uncommon).

May 22, 2010 | 1998 Saturn SL

3 Answers

Cltuch 97 excel


dont listen to them, easiest way is: remove air intake box(3 nuts)
remove nuts surrounding the outer gearbox(about 6) and then remove the gearbox mounts
lower the gearbox and move slightly to the drivers-side. best to put a block or jack under it. then take the fly-wheel off(marking where it sits against the clutch kit)
and then pull the clutch plate off, making sure all fingers are not bent. i picked up a full clutch kit 2nd hand for 25$

Nov 14, 2009 | 1990 Hyundai Excel

3 Answers

When i put in gear then let out on clutch the car


sounds like u have a worn out clutch or a faulty pressure plate

Jul 08, 2009 | 1995 Ford Probe

2 Answers

Fly wheel ring gear replacement


You need to pull the tranny out.
Then the flywheel needs to be unbolted from the engine.
if it's an automatic, purchase a new flywheel, if its a clutch, you can have a new ring gear pressed on to the flywheel...

May 28, 2009 | 1984 Ford Bronco II

1 Answer

Clutch will not disengage


Check the reservoir on the firewall near the master cylinder. If the reservoir is empty fill it with brake fluid and pump the clutch and bleed the air out on the side of the transmission.

Apr 23, 2009 | 1984 Ford F 150

Not finding what you are looking for?
2003 Volkswagen Jetta TDI Logo

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...