Question about Cars & Trucks

Open Question

Fx35 torque spec

I would like to know the torque spec on the bottom oil pan bolts on an infinity fx35

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

Ad
  • 158 Answers

SOURCE: 2000 sebring transmission pan torque spec

10 ft lbs no real patterm needed

Posted on Apr 03, 2009

moparownr
  • 667 Answers

SOURCE: Need torque specs for oil pan bolts

torque specs for these bolts can be found in a Haynes or Chilton manual availiable from your local parts store, or maybe at your local library, however these bolts are usually no more than 14 ft pounds, unlike cylinder head bolts, the bolts do not need to have any stretch factor to hold the oil pan gasket in place or sealed.

Posted on May 22, 2009

  • 743 Answers

SOURCE: oil and transmission pan bolt torque specs

124 inch lbs on oil pan...Transmission pan 13 ft lbs.

Posted on Oct 12, 2009

  • 106 Answers

SOURCE: i need bolt torque specs for a 2006 chevy cobalt

if you just go to a mecanic and ask what are the specks on that they should know but i think if you just tighten them down with an impact wrench till it is really tight after ou start the car it will run like **** then it will work its self out

Posted on Nov 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

98 jeep wrangler tj 4.0 oil pan bolt pattern or layout. An torch specs


Bobby, oil pan bolt torques for 4.0 Wrangler. Oil Pan Bolts 1/4 84 in-lbs Oil Pan Bolts 5/16 132 in-lbs As far as sequence, see last link, start in center, criss cross pattern tighten snug all, then repeat to torque spec.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Oil Pan Gasket leaking
http://jeephorizons.com/tech/99_40l_torque_specs.html
98 jeep 4 0 oil pan bolt torque sequence specs Google Search

May 21, 2016 | Jeep Cars & Trucks

1 Answer

How to remove oil pan


jack it up, drain oil from drain plug on oil pan when drained remove and replace oil filter also. remove the pan bolts pull off pan and gasket.put new oil pan gasket on if needed.when oil pan bolts are back in, screw them in hand tight, then torque them down to specs and alter nate the tightening so it wont damage pan seal. any auto parts store can tell you the torque on the bolts for your car. good day!

Mar 31, 2014 | 1999 Chevrolet Venture

2 Answers

Crank sensor - infiniti fx35


Look at the rear of the oil pan on the left side. You should see the sensor with one (1) bolt retaining the sensor in it's place. (see illustration on right).
j22100g7.jpg


7678cd23-7a05-46f6-830b-df8cafde13ff.jpg

Jul 04, 2013 | Infiniti Cars & Trucks

1 Answer

Need torque specs for 96 yukon 5.7 liter


Here's a link to the oil pan removal guide with pan bolt torque specs.

Jan 13, 2013 | 1996 GMC Yukon

1 Answer

I need to know he torque spects for the oil filter container the bolts on to the moter on a 94 BMW 318i...there are 6 bolts...I also need to know the torque spects on the alternator mounting bracket...


OIL PAN OR TRANSMISSION PAN BOLTS TORQUE ABOUT 7 FT LBS. CAN GET SPECS ON BOLTS SIZES. IF BOLTS SIZES IS 13M I4M 15 M TORQUE BOLTS ABOUT 55 TO 80 FT LBS

Nov 11, 2010 | 1994 BMW 3 Series

1 Answer

What is the oil pan bolts torque spec for a 2002 jaguar X-type V-6


Fig. Oil pan bolt torque sequence-X-Type

b8259f9.jpg



  1. Use a new oil pan gasket. Tighten the bolts, in the sequence shown, to 18 ft. lbs. (25 Nm).
  2. Tighten the pan-to-transmission bolts to 33 ft. lbs. (45 Nm).
  3. Tighten the access cover bolt to 89 inch lbs. (10 Nm).
  4. Tighten the compressor bolts to 18 ft. lbs. (25 Nm).
  5. Refill the engine with oil.
  6. Install the transfer case.
Hope this helped (rememer comment and rated this).

Apr 14, 2010 | 2002 Jaguar X-Type

1 Answer

Need torque specs for oil pan bolts


torque specs for these bolts can be found in a Haynes or Chilton manual availiable from your local parts store, or maybe at your local library, however these bolts are usually no more than 14 ft pounds, unlike cylinder head bolts, the bolts do not need to have any stretch factor to hold the oil pan gasket in place or sealed.

May 17, 2009 | 1997 Ford Ranger SuperCab

1 Answer

Oil and transmission pan bolt torque specs


124 inch lbs on oil pan...Transmission pan 13 ft lbs.

May 06, 2009 | 1991 Buick Park Avenue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...