Question about Cars & Trucks

1 Answer

Abs light goes on and then off once it goes off and I step on the brake it pulls to the right check gor codes and nothing ccoms up

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 5 achievements.


    An expert who has answered 20 or more questions within one hour.


    An expert who has answered 20 questions.

  • Contributor
  • 34 Answers

Not sure what the vehicle is but could be a brake BRAIN problem.

Posted on Nov 18, 2013


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 599 Answers

SOURCE: abs , brake, traction control light on in 04 lesabre

check to make sure that all the the bulbs in the rear are working,even the third light

Posted on Apr 08, 2009

  • 1902 Answers

SOURCE: Brake/ABS brake issue on 2001 Sport Trac?

Check for air in the system, Also check your brake calipers to make sure that the Pistons are not freezing or just locked up

Posted on Apr 13, 2009

  • 201 Answers

SOURCE: 1993 toyota landcruiser brake problem

sounds like vacuum brake booster diaphram has failed. its behind master cylinder and probably needs replacing.

Posted on May 08, 2009

  • 6 Answers

SOURCE: brake pedal being soft on 02 town and country

Add brake fluid and bleed the air out of the brake lines.

Posted on Jun 06, 2009

  • 1486 Answers

SOURCE: abs and vtm-4 dash lights on. When driving under

Your wheel bearing is the fault.Get it changed ASAP.Good luck hope that was helpfull.

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Why is the abs light in my 1994 camero stuck on is it serious


Feb 22, 2015 | Cars & Trucks

1 Answer

My ABS light is on and my brakes work fine. every once in a while the light goes off and the brakes act like the anti-brake system should. What seems to be the problem?

The warning light is telling the driver the system is disabled. The hydraulic brake system works independently from the ABS altho the ABS does use some hydraulic components.
You would need to have the ABS checked for trouble codes to proceed.

Aug 09, 2013 | 2002 Buick Rendezvous

1 Answer


gm had a problem with the abs systems on their 1999 trucks and cars the sensor seat would corrode and move slightly enough to set off the low speed sensor of the abs usually goes off at 5mph and less and doesnt set off the abs trouble code need to remove the front wheels and brake assembly to access the hub and abs sensor also check hub to make sure its ok- in the mean time pull the fuse on the abs ur brakes will go to a normal brake without the abs meaning if u step on brake hard[panic brake] u can lock up tires

Apr 09, 2013 | 1999 Buick Century

1 Answer

How do you clear stabillity controll light and abs light

Most likely yu cause a problem with the abs system since the stability control uses this system it will also illuminate when there is an ABS issue. If there where not a problem the light would have gone out. Since the light remains on we now something is wrong. Doyle check your work making sure you didn't accidentally unplug, break, or pull the wires out of a sensor. If nothing looks wrong than your next step is to check for ABS codes with a scan tool.

I’m happy to assist further over the phone at

Aug 11, 2012 | 1999 Cadillac DeVille

1 Answer

I have a 99 chevy my abs light on dash is on once that happens the break ligjt comes on speed gage stops wooking then transmission does not want to go shoft onothing ive checked fuses replaced te speed...

ok first lets address the abs light. Have you tried to have the codes read?usually an abs light is due to a faulty wheel speed sensor. once that happens with the brake light and speedometer quites working, it sounds like the truck goes into shutdown mode as to not damage the truck any more. The first step is to find out what codes are thrown and address the problems then go on to the next problem.

May 28, 2012 | 1999 Chevrolet Silverado 1500

1 Answer

1993 Lincoln Town car 3 years ago on a very HOT day my right front brake started violently grabbing, even without touching the brake. The ABS light comes on intermittently, it usually goes off after...

I had a very similar problem in my 93 town car. I ended up changing the Calipers, rotors, and pads. This stopped the grabbing, but still every once and a while the ABS light would come on and grip the brakes on me. I ended up pulling the ABS relay from under the hood.and the problem has stayed away. The only thing is that now i dont ABS brakes. Its a heavy car tho and i havent had an issue yet. Also, if you decide to do this, the relay way mis marked in my car, when i pulled the ABS relay, the Air shocks went out instead. Had to pull one at a time until the anti lock light came on, then i knew i had it.

Jul 13, 2011 | 1993 Lincoln Town Car

1 Answer

Hi, how are you? when the engine starts and after removing parking the ABS light sensor and the BAS light sensor goes on.. what does it mean ?

Hi there,

ABS: this is your Anti-lock Braking System.
BAS: this is your Brake Assist System.

The first thing I would suggest you check - press the brake pedal and confirm if your brake lights work. If not, then you have a faulty brake switch (on the brake pedal).

If lights DO work, then the next step is to have your Fault Codes read from your vehicle's computer - this step will identify which circuit/component has triggered these warning lights.

Note: It will take your local Dealership approx. 15mins to check these codes, so shouldn't cost much.


Jun 07, 2011 | Mercedes-Benz C-Class Cars & Trucks

1 Answer

Abs light stays on I have put new brake line on new calipers because they were sticking causing brakes to get hot, thats all fixed but light still stays on.

the ABS light is on because there has been a fault detected by the ABS module. It has nothing to do with the actual braking system.

The ABS module does a self check every time you start the vehicle. If it detects a problem during that self check the ABS light will stay illuminated and a code or codes for the fault will be stored in the ABS module. Scanning the module will allow you to pull the codes and proceed with diagnosing why the fault is occurring.

The most common source of ABS problems is bad wheel speed sensors or broken wires to the wheel speed sensors. Again pulling the codes from the ABS module will narrow down the possibilities.

Once you now what codes are present post them and we will be happy to assist you further.

I’m happy to assist further over the phone at

Apr 21, 2011 | 1998 Chevrolet S-10 Pickup

2 Answers

I Have a 2002 Dodge Ram 2500.Both the ABS and Brake Lights are on


Did you have the ABS sensors checked ?? The brake fluid level when low also activates the Brake and ABS lights?? Drive truck to an AutoZone store and ask to have computer codes scanned. This is a free service for all customers. This will help you to pinpoint the problem.

Good Luck!!

Don't forget to rate this post.

Jun 04, 2010 | 2001 Dodge Ram 2500 Truck

1 Answer

The abs light is off 50% of the time and on 50% of the time. when it's on it blinks. how do i fix it? brake pads and disks have been replaced.

First thing ABS is the Anti Locking Brake system, this has nothing to do with pads or rotors.

The ABS consists of a control module, pump & sensors.
Without having a scan tool to check to see which code is set you can't fix it.
Anytime one of the components listed above fails or is having a problem that will send a signal to the EBTCM (Electronic Brake Control Module) which cause the ABS light to come on.
You can spend thousands of dollars replacing parts before you get it right, and the light would still be on because you need the scan tool to clear the light once the problem is fixed.
It would be best to find a trusted mechanic to scan the codes & diagnose the problem.

Oct 13, 2009 | 2002 GMC Savana

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15427 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides