Question about Toyota Celica

Open Question

Rear brake imbalance - Celica Toyota Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 83 Bronco 351w I am doing the brakes and the passenger side rotor needs to be replaced can someone walk me through this thanks


Personally I would replace both rotors to prevent a future brake imbalance.

* chock rear wheels, raise front of vehicle and place on stands.

* remove wheels, remove brake calliper and bracket assemblies.

* remove bearing hubs from axles, via removal of bearing adjustment nut

*remove hub seals, clean and inspect bearings, repack with HT bearing grease.

* the brake rotor bolts to the rear of the hub, you will have to remove and replace rotor to hubs, make sure all bolts are thread locked with loctite 263 and tensioned to spec.

* pack hub with grease, install seals, fitt hub assembly and adjust wheel bearing preload, install new split pins.

* fitt brake calliper and brackets, fit new brake pads,

* fitt wheels lower vehicle, test brake for function

Hope this helps..

Aug 02, 2016 | Cars & Trucks

1 Answer

Front end probably


Bent wheel, defective tyre, wheels out of balance, alignment and uneven tyre wear, defective or worn shock absorbers, excessive wear or lash in the steering/suspension components, binding front brake(s), front brake discs warped or excessive axial runout...

Most commonly it is wheel imbalance that is the culprit.

Apr 11, 2016 | 2007 GMC Yukon XL

1 Answer

Rear axle offside imbalance


I change one time a metering valve on rear of engine it was y like valve dont remenber what kind of car

Apr 10, 2014 | 1998 Toyota Corolla

1 Answer

My dash lights come on when my brakes are pushed in my 93 nissan pick-up


If you mean the brake warning light on the dash is coming on, it is telling you that you have a problem with your hydraulic system, There is a switch that senses an imbalance between the front and the rear brakes. First check your brake fluid, if it's low than you have a external leak. If it's not low, the master cylinder has failed internally.Lokk for brake fluid leaks behind each wheel and at the back of the master cylinder. If you can find a leak or it's not low on fluid you had a bad master cylinder.

Jan 22, 2011 | Nissan Pickup Cars & Trucks

1 Answer

How do you reset the brake warning light on a 1993 Mercury Cougar xr7?


you will likely have to bleed the brakes, as it is most likely an imbalance between the two sides of the system. if you have fixed the problem, bleeding usually will fix it, otherwise look for a button on the proportioning valve. also look at the ABS system.

Sep 02, 2010 | 1993 Mercury Cougar

2 Answers

Bad virbration


You may have rotated imbalanced wheels from the rear to the front .Its possible not to feel the imbalance from the rear as it is far less sensitive and not transmitting through the steering wheel. Check tire balance or move the tire back to their original position which might help veify the source of your imbalance.

Aug 23, 2009 | 2004 Jeep Wrangler

2 Answers

1994 saturn sl


What about rear brakes, have those been checked out? sometimes even a drum can warp, it could also be an imbalaced tire, maybe even an untrue rim. normally bouncing comes from an imbalance somewhere.

Jun 01, 2009 | 1994 Saturn Sl

2 Answers

Brake light on


There is a brake system balance valve that has a wire going to it. Typically near the mater cylinder where you put the fluid in. Remove this wire from the valve. ( You will also see 4 brake lines going in to this valve) If the light goes out, there was an imbalance in the front to rear brake system that tripped the light. You need to find the cause of this. This happens most often when someone replaces the front or rear brakes, and is pumping the brake pedal to get the pads or shoes seated onto the rotors or drums.

Getting the light to go out is a matter of bleeding the brakes, during this process you will cause an imbalance in the opposite way that caused the light problem to start with.

You need to find the cause of this light going on. Have the brakes inspected by a qualified garage telling them what happened

Good Luck!

Feb 09, 2009 | 1996 Chevrolet Blazer

2 Answers

1991 honda civic brake light stays on need to push brake pedal to


Sounds like you might have a caliper that is stuck and is not fully disengaging. If it is in the rear then you may have a bad rear caliper. Twoo things you can try. One is to crawl under the ca and adjust the tension two nuts on the emergency brake line. If that does not resolve the problem then remove the back tire and try to spin the drum or rotor whichever you may have. If it does not spin then try adjusting the e brake cable more if it still does not respond then you need to do a brake rebuild. Also does it pull while it is dragging? If it is then you will need to rebuild the brakes no matter what.

Feb 06, 2009 | 1993 Honda Civic 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...