Question about Toyota Cars & Trucks

1 Answer

Light's on reminder

2007 Camry stopped dinging when the lights are left on by accident. What are some possible solutions to enable the chime again.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,889 Answers

Replace the blown fuse in the fuse box labeled "chime"

Posted on Nov 18, 2013

  • Jay Lee
    Jay Lee Nov 19, 2013

    I couldn't find the "chime" fuse anywhere. I checked all fuses with an ohm meter and all checked good.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: 91 toyota camry door ajar light stays on along with the chime

Probably a faulty door switch. Are you familiar with what I'm talking about. Little push like switches that the doors push on as they close, usually on door post by latch end, or sometimes in jamb of door at hinge end.

Posted on Jan 25, 2009

  • 512 Answers

SOURCE: 2007 Jeep Wrangler airbag light and chime

there is no other option...as long as the light is on there is a chance the airbag will either not work in an accident or it may deploy without warning. how many miles do you have on the vehicle??? there is a chance if you contact chrysler customer relations they may assist in the repairs.

Posted on Jan 25, 2009

  • 16 Answers

SOURCE: Chime always "dings"

take fuse out

Posted on Mar 12, 2009

  • 1 Answer

SOURCE: Maintanance light on a 2007 Toyota Camry LE

Push and hold trip button on dash with key off, turn key on but don't start, odometer will clock down, when it is finished, lite will go off

Posted on Apr 08, 2009

  • 1 Answer

SOURCE: my 1999 buick lesabre has a dinging noise when a brake sensor

This means your master cylender is low on brake fluid , top it off with brake fluid and that should solve your problem . You should find out where the brak fluid is going .

Posted on Sep 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 ford focus air bag sensor light stays on, also seat belt light with chime on also


Your airbag system is screwed up. Get to a shop immediately because its trying to tell you that your airbags won't work if you get in an accident.

Apr 11, 2013 | Cars & Trucks

1 Answer

Warning Chime dings when neither key in the ignition and headlights are off


close the doors make sure they r all closed r turn your dome light off my toyota camry does it all the time

Sep 30, 2012 | 1999 Ford Explorer

1 Answer

When driving our 06 mustang we hear a series of 4 dings, pause, then the dings again and no light flashes on the dash. It sort of dings like the sound when your seatbelt is not fastened, when it is. It...


30 minutes or seconds? does the dome lamp come on, like one of the doors not closed all the way? A good repair shop or the Ford dealer can get a scanner and watch for the belts, doors, lights, ect ( I think thats the only thing that will ring a chime) as you drive and see whats making it go on.

Nov 19, 2010 | 2006 Ford Mustang

1 Answer

I own a 2007 montana and had it for 1 month now ..It keeps making a ding ding ding chime while driving ..The passengers rear door is automatic and when I press the button it makes the same noise but when...


1. Turn off the overhead over-ride switch. Drive again. Do the chimes stop? If yes, the door is not closing properly due to the door contacts. Clean them yourself or have them serviced.
2. If the chimes did not stop in step 1. above, it's not likely the door but rather something else.
3. Chimes occur for many reasons. Suggest checking - a. are the rear back-up warning sensors blocked/dirty? b. any other lights on the dash like oil, abs, airbag, etc? c. passenger side airbag disabled - something heavy placed in passenger seat?

In my experience, it's the automatic door contacts. We have a long history of problems with these auto doors, that are still not resolved. problems all throughout the warranty period, and now into the extended warranty period. We must unite and get GM to resolve the quality of these doors. My next step (next incident) is going to be to have the dealership inspect the entire wiring system.

Oct 14, 2010 | 2007 Pontiac Montana

2 Answers

While I start driving, the Chime box goes off! Ding Ding Ding Ding...etc..over and over again. How Can I disable the chime box on my 93 Buick Park Avenue?


Is this the warninng that you are not wearing your seat belt? The way to make it stop is to wear your seat belt.

Mar 10, 2010 | 1993 Buick Park Avenue

1 Answer

I have a 1999 Olds Intrigue, headlight left on alarm is stuck


The Body Control Module (BCM) controls the audible warnings. Refer to Body Control System Description in Body Control System for more information regarding the BCM.
The body control module (BCM) controls these reminders:
• Key in ignition reminder: An audible warning intended to remind the driver that the key has been left in the ignition cylinder. The BCM sounds the chime for this reminder at a rate of 150 chimes per minute.
• Fasten seat belt reminder: An audible warning intended to remind the driver at the beginning of the driving cycle that the driver's seat belt is unfastened. The BCM sounds the chime for this reminder at a rate of 50 chimes per minute.
• Fasten belts indicator control: A visual warning intended to remind the driver that the driver's seat belt is unfastened.
• Parking brake reminder: An audible warning intended to remind the driver that the parking brake has been left applied with the transaxle shifted out of PARK. The BCM sounds the chime for his reminder at a rate of 200 chimes per minute.
• Turn signal reminder:
An audible warning intended to remind the driver that the turn signal has been left on while the vehicle has traveled over 1.2 km (¾ mile). The BCM sounds the chime for this reminder at a variable rate (in unison with the turn lamps on) of 90 chimes per minute.
• Headlamps ON reminder: An audible waring intended to remind the driver that the headlamps have been left on. The BCM sounds the chime for this reminder at a rate of 200 chimes per minute.
• Last door closed locking confirmation: An audible warning intended to provide the driver feedback that the last door closed locking feature is active. The BCM sounds the chime for this remainder at a rate of 200 chimes per minute.
• Feature customization and diagnostics feedback: An audible feedback used when changing feature customization modes. Also used by service technicians during the BCM diagnostics. The BCM sounds the chime during the feature customization, and also during diagnostics. Refer to Body Control Module (BCM) for additional information.

Step
Action
Value(s)
Yes
No
1
Was the BCM diagnostic system check performed?
--
YES - Go to Step 2
NO - Go to Diagnostic System Check - Body Control System in Body Control System
2
Check for Powertrain Control Module (PCM) Diagnostic Trouble Codes (DTCs). Refer to Powertrain On Board Diagnostic (OBD) System Check (LX5) or Powertrain On Board Diagnostic (OBD) System Check (L36) in Engine Controls for more information.
Are there any PCM DTCs present?
--
Go to Appropriate DTC Table in Engine Controls
Go to Step 3
3
Connect a scan tool to the Data Link Connector (DLC).
Using scan tool, select BCM data display inputs and monitor the park brake switch input.
While observing the scan tool, apply and then release the park brake.
Does the scan tool indicate that the park brake input is off while the park brake is released?
--
Go to Step 7
Go to Step 4
4
Turn the ignition switch off.
Disconnect the scan tool from the DLC.
Disconnect the BCM connector C1.
Release the park brake.
Using a test light, connect between B+ and the BCM connector C1 terminal D5.
Is the test light off?
--
Go to Step 7
Go to Step 5

Your best bet ,take it to a qualified repair shop

Aug 01, 2017 | 1998 Chevrolet S-10 Pickup

1 Answer

Engine light comes on, stays on, doesn't blink,


The last chime is most likely an audible reminder that the check engine light is on. It would be advisable to get the car scanned to see why the light is on. Even if the car seems to be running ok, your fuel economy or emissions could be worse than they should be.

Jul 28, 2009 | 2005 Chrysler PT Cruiser

2 Answers

Oil change reminder light phenomenon


No it is not possible. The manufacturer has engineered the vehicle so I suppose they know when the maintainence should be performed. Do you need assistance with resetting the oil=life monitor?

Apr 25, 2009 | 2009 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...