Question about Mercedes-Benz 420-Series

1 Answer

Gas pedal replacement

Need to replace

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Mercedes-Benz Expert
  • 300 Answers

Fairly easy to replace,I bought mine on Ebay

Posted on Nov 29, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the accelerator pedal position sensor?


You need to replace the accelerator pedal assembly ! That's the whole gas pedal assembly , two bolts hold it fast to the fire wall . Search from over 10 Million Auto Parts P2138 APPS Accelerator Pedal Position Sensor Fix 3 5L Chevrolet Impala

Feb 27, 2015 | 2006 Chevrolet Impala

1 Answer

How do i replace a ford focus throtle cable


disconnect the throttle cable from the throttle body. follow the throttle cable around the engine and you will find it goes through the fire wall and connects to the gas pedal. disconnect the cable from the gas pedal and pull out of the cab compartment from engine side. Pay close attention to how you disconnected the cable from the gas pedal and from the throttle body because you will have to reverse this procedure when you install the replacement. You will need an assistant who is pretty flexable to connect the cable to the gas pedal. so let the assistant disconnect the old cable from the gas pedal so he or she will know how to connect the new one back to the gas pedal. It was not an easy project for me and it definitely is not as easy as it seems to be. You will need plenty of time, daylight and patience. The replacement cable may be shorter than the original and that ok. Ford has made sure it will work. Use tie-wraps or zip-ties to hold the new throttle cable back in place around the engin. Good luck.

Jun 26, 2014 | 2000 Ford Focus

1 Answer

How do you reset the gas pedal


If you are "resetting" the gas pedal because you replaced it..... you will need to return to the Honda dealer to have your computer "flashed" . The pedal MUST be replaced with a new unit, you cannot use "salvaged" parts for the gas pedal. It will not work.

May 18, 2014 | 2000 Honda Passport

1 Answer

1995 ford taurus when i press my gas pedal its not giving enough gas to the car


check fuel pressure if pressure is low replace fuel filter .check pressure again if still low replace fuel pump

Apr 06, 2014 | 1995 Ford Taurus

1 Answer

How to replace a gas pedal for a 2000 jetta vr6. its a drive by wire system. i have a new one and would like to replace it myself...please advise..thank you


There are 3 nuts that are 13mm that secure the pedal assembly to mounting studs, you'll have to remove the plastic trim below the steering wheel to gain access. Once those are removed, there is a plug connector with two tabs that must be squeezed towards the center to release the wire harness connector. Worth noting is that these pedal assemblies rarely fail, and if your gas pedal isn't doing anything, it could be frayed or shorted wires to your O2 sensor as that can cause an EPC light and non-functioning gas pedal, due the O2 sensor sharing logic with the gas pedal. If that is the case, then the remedy is to replace the ECU and repair the O2 wire harness prior to programming the ECU.

Apr 05, 2014 | Cars & Trucks

2 Answers

09 impala accelerator pedal sensor?


the pedal sensor is part of the gas peda assembly. The whole thing needs to be replaced if there is a problem with the sensor.

Feb 16, 2012 | 2009 Chevrolet Impala LT

1 Answer

Ford Taurus 2002. The excelerator cable detached at the gas pedal. The cable is not frayed, however, the small cup at the end of the cable that slides in place onto the gas pedal arm is broken. Do I need...


You probably should replace the entire cable. You may, however, get away with using a cable clamp to replace the cable fitting.

Try registering at www.autozone.com (it's free). Once registered you'll have access to some great DIY vehicle repair manuals. I'm sure you'll find something useful.

Dec 15, 2010 | 2002 Ford Taurus

1 Answer

I need to replace the Automatic Transmission Accelerator Pedal Position Sensor #53031575ah. Where is it located?


it is the actual gas pedal. if you look you will see the module attached to the pedal. so the replacement should be the whole pedal assembly

Aug 25, 2009 | 2004 Dodge Ram 2500

1 Answer

Engine drops speed when I press gas pedal


Ignition distributor caused problem. Rotor element needs replacement.

Jul 21, 2008 | 2002 Mitsubishi Lancer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...