Question about Cars & Trucks
I have a 1993 isuzu spacecab with 310,000 miles runs great however of late it's having difficulty starting after the engine is warm. Restarts after it cools tempature is good idles well after start. Cleaned filter and mas airflow sensir Got codes 12. 33. 34
Crank position sensor. When car heats up the sensor gets hot and fails. You need to replace it and youre good to go.
Posted on Nov 17, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Did you sync up the engine properly when you reinstalled the timing belt/chain? It is possible to be on the marks and be 180 degrees off. Align the timing mark on the crankshaft then check the rotor position.If it doesn't point to number one wire terminal position roll the engine over until the crank lines up to the timing mark again. The distributer needs to be pointing the wire terminal that goes to number cylinder.Any other position is unacceptable and you can't simply turn the distributer to number one either You need to retime the crankshaft to the camshft making sure that the distrubitor points to number one and both valves for number one cylinder are completely closed.
Posted on Nov 30, 2008
SOURCE: colt idle problem.
Most likely you have a bad Idle motor which is a small motor mounted on the intake manifold. If the motor can run better with your foot on the gas but dies if removed then it is probably this. This motor is controlled by the OBDII computer which gets it's control signal from the temp sensor which is located either on the radiator or engine block (which could also be bad), if the electric fan (if equipped) turns on then this is not the problem part, but the idle motor is. Another possibility is that you have some bad /cracked vacuum hoses which should be checked for first, before replacing the idle motor.
Posted on Nov 30, 2008
SOURCE: Engine stalls
sounds like one of a couple things could be causing you problems first would be the fuel pump may be wearing out. these are a mechanical pump and should be producing over 35psi at the injection pump if you have a way to put a gauge on it you could check this under full throttle is when you want to watch it though. fuel gauges are quite inexpensive and are handy to have in the truck anyway. another thing i have seen cause this is the check valve on the discharge of the pump there is a spring and ball in the return line banjo fitting that holds the fuel pressure at a constant 35 psi when that gets weak it allows more fuel to return to the tank which will let it run at lower rpm's but not under full load. hope this helps
Posted on May 18, 2009
SOURCE: rough idle after warm up
I'd take a look at the temp sender...the engines computer may be
"thinking" the engine is still cold when it's not. That would cause it
run rich (and rough) after it's warmed up. Generally the sender can be
tested with an ordinary volt/ohmeter but you will need the
specifications available in most inexpensive manuals. As with any
complicated electronics system, I can only give you my best guess,
without the luxury of doing any hands-on testing myself.
Posted on May 28, 2009
Tips for a great answer:
Mar 24, 2014 | 1993 Isuzu Spacecab
Mar 25, 2011 | 1993 Isuzu Rodeo
Aug 25, 2010 | 1990 Isuzu Spacecab
Jun 01, 2010 | 1990 Isuzu Spacecab
Mar 02, 2009 | 1993 Ford Ranger SuperCab
Feb 22, 2009 | 1993 Ford F150 SuperCab
Feb 16, 2009 | 1988 Isuzu Spacecab
Oct 13, 2008 | 1993 Isuzu Spacecab
68 people viewed this question
Usually answered in minutes!