Question about Cars & Trucks

Open Question

Mazda 5 clock adjust - Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change clock in 2007 Mazda r


Hold Clock to get it in the set 12/24, tap Set to move to 12hr, tap clock to move to the hour, tap set to get to the right hour, tap clock to move to the minute, tap set to get it to the right minute, tap clock to back out of it.

Mar 09, 2015 | Mazda Cars & Trucks

1 Answer

Clock radio reset


Push clock button in and hold until it blinks.
button #5 is hour adjust.
button #6 is the minute adjust.
button #4 is set.

Jan 25, 2012 | 1996 Suzuki X-90

1 Answer

Firing order mazda 626 2000


you didn't specify which motor you have,, here are the normal Mazda firing orders The firing order fot the 1.6 four cylinder is 1-3-4-2. The direction of rotation is counter clock-wise. Hope this helps. For the v6 its 1-2-3-4-5-6, also counter clock-wise. Easy enough.


Sep 15, 2011 | Mazda 626 Cars & Trucks

1 Answer

I own a 1990 Mazda MX5 and the headlights need adjusting - how do you adjust them please. The housing is flush with the bonnet so no need to adjust this just the aim.


After taking off the covers which suround the head lamps. There are two screws 1 in the 6 0`clock position to adjust the up and down position and one in the 9 0`clock position to adjust side to side position

Feb 14, 2011 | 1990 Mazda MX-5

1 Answer

Setting clock on 2006 Pt crusier


Clock Setting Procedure (digital clock page 242 of your owners manual)
1. Press and hold the time button until the hours blink.
2. Adjust the hours by turning the right side Tune/
Audio control.
3. After the hours are adjusted, press the right side
Tune/Audio control to set the minutes. The minutes will
begin to blink.
4. Adjust the minutes using the right side Tune/Audio
control.
5. To exit, press any button/knob or wait 5 seconds.

SETTING THE ANALOG CLOCK (page 238 of your owners manual)
To set the analog clock at the top center of the instrument
panel, press and hold the button until the setting is
correct. The clock will adjust slowly at first and then
quicker the longer the button is held.

Jan 26, 2011 | Chrysler PT Cruiser Cars & Trucks

1 Answer

How do I set clock on a 2006 Pt Cruiser. I hold the time button down and can set hour but can't set minutes.


Clock Setting Procedure (digital clock page 242 of your owners manual)
1. Press and hold the time button until the hours blink.
2. Adjust the hours by turning the right side Tune/
Audio control.
3. After the hours are adjusted, press the right side
Tune/Audio control to set the minutes. The minutes will
begin to blink.
4. Adjust the minutes using the right side Tune/Audio
control.
5. To exit, press any button/knob or wait 5 seconds.

SETTING THE ANALOG CLOCK (page 238 of your owners manual)
To set the analog clock at the top center of the instrument
panel, press and hold the button until the setting is
correct. The clock will adjust slowly at first and then
quicker the longer the button is held.

Jan 26, 2011 | Chrysler PT Cruiser Cars & Trucks

1 Answer

Looking to find the correct specs to adjust a TPS for a 1994 Mazda 929. Using a multi-purpose voltmeter.


YOU NEED 2 VOLT METERS.FIRST OF ALL START ENGINE.LET IT GET OPERATING TEMPERATURE THEN TURN OFF ENGINE.THEN YOU CONNECT TWO VOLT METERS TO THE TEST CONNECTOR.TURN IGNITION ON AND CHECK THAT CURRENT FLOWS TO ONLY ONE VOLT METER.IF BOTH VOLT METERS SHOW CURRENT FLOW REMOVE THE CAP AND TURN THE ADJUSTING SCREW COUNTERCLOCKWISE UNTIL ONE VOLT METER SHOWS CURRENT.IF NO CURRENT IS REGISTERED BY EITHER VOLTMETER TURN THE ADJUSTING SCREW CLOCK WISE UNTIL ONLY ONE VOLT METER SHOWS CURRENT.INSTALL THE CAP ON THE ADJUSTING SCREW AND DISCONNECT THE THROTTLE SENSOR CONNECTOR.CONNECT AN OHM METER TO THE THROTTLE SENSOR TERMINALS.OPEN THE THROTTLE VALVE AND CHECK THE RESISTANCE READING FROM THE THROTTLE SENSOR.AT IDLE THE THROTTLE SENSOR SHOULD SHOW ABOUT ONE KILO OHM RESISTANCE.AT WIDE OPEN THROTTLE THE SENSOR SHOULD SHOW ABOUT 5 KILO OHMS RESISTANCE.ANY RESULTS OTHER THAN THESE.REPLACE THE THROTTLE SENSOR AND RETEST.

Aug 26, 2009 | 1994 Mazda 929

1 Answer

How to replace the serpentine belt of protege 5 2002, also need the routing diagram


Posted by Asker under 1997 Mazda Protege for their 2002 Mazda Protege 5.
Both are included Below

Click on the following free direct Link. It has the Belt Diagrams for the 1997 Mazda Protege with either the 1.5L DOHC In-Line 4-Cylinder or 1.8L DOHC In-Line 4-Cylinder Engines; along with various engine options (AC/No AC, etc.). Included are Instrucional Diagrams for loosening (for removal) and tightening (for replacement) using the Adjustment and Locking Bolts/Nuts.
http://www.2carpros.com/car_repair_information/year/1997/make/mazda/model/protege/1997_mazda_protege_drive_belt_routing_diagram.htm

Click on the following free direct Link. It has the Belt Diagrams for your 2002 Mazda Protege 5 2.0L DOHC In-Line 4-Cylinder Engine; along with various engine options (AC/No AC, etc.). Included are Instructional Diagrams for loosening (for removal) and tightening (for replacement) using the Adjustment and Locking Bolts/Nuts.
http://www.2carpros.com/car_repair_information/year/2002/make/mazda/model/protege5/2002_mazda_protege5_drive_belt_routing_diagram.htm

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Apr 13, 2009 | 1997 Mazda Protege

2 Answers

Change the time on a Mazda MPV 1999


you cant, the clock runs off the sat nav system. so it will only show the correct time of the country the sat nav is set up for.
cheers
mikey

Jun 23, 2008 | 1999 Mazda MPV

2 Answers

Mazda 5


You might see if there is a camber caster shim pack that can be added.

May 14, 2008 | 2007 Mazda MX-5 Miata Touring Convertible

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...