Question about Nissan Prairie

Open Question

Remove starter motor nissan prairie 1997 - Prairie Nissan Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

mrgreenz
  • 962 Answers

SOURCE: starter motor

  • If your testing indicates that the starter must be removed, the first step is to disconnect the negative cable at the battery.
  • It may be necessary to place the vehicle on a lift to gain access to the starter. Before lifting the vehicle, disconnect all wires, fasteners, and so on that can be reached from under the hood.
  • Disconnect the wires leading to the solenoid terminals.
  • To avoid confusion when reinstalling the starter, it is wise to mark the wires so they can be reinstalled on their correct terminals.
  • On some vehicles you may need to disconnect the exhaust system to be able to remove the starter.
  • Loosen the starter mounting bolts and remove all but one.
  • Support the starter while removing the remaining bolt.
  • Then pull the starter out and away from the flywheel.
  • Once the starter is free, remove the last bolt and the starter.
  • Once the starter is out, inspect the starter drive pinion gear and the flywheel ring gear.

Posted on Nov 07, 2008

  • 2 Answers

SOURCE: Starter motor and ignition switch and O2 sensor and pipe 1997 Nissan Maxima

You need to remove all of the air intake and other things behind the battery. The start motor is held in with two bolts. You might need a breaker bar to break loose the one bold as I did. Once you remove all of the air intake equipment. This will help you gain access to the starter motor. You might not need to remove all the air intake equipment I know it made it alot easier for me to remove the starter and I took it to the auto store and had it tested.

Posted on Apr 07, 2009

  • 171 Answers

SOURCE: My Nissan Prairie wont start it only goes click

Did you try jupp starting the car?
Sounds like you have a low battery?

Posted on Mar 02, 2010

  • 360 Answers

SOURCE: Dumb question... According to AllData, this is the

Perhaps you're reading more into this than is really there.

The AllData advise sounds accurate, and I'm confident the spirit of the instruction is to perform these initial steps from under the hood (on the top side of the engine). Having completed the initial steps, go under the car and actually physically remove the starter from underneath.

Did you purchase a single vehicle subscription to AllData from AutoZone? The basic subscription is for only one year. For about the same amount of money you can purchase a vehicle specific repair manual and use it until you wear the ink from the pages. I'll take hardcopy over internet any day!

Posted on Feb 08, 2011

  • 2430 Answers

SOURCE: I have a nissan prairie

Check circut from ign.switch to starter motor with key on start, if voltage there starter motor at fault

Posted on May 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My nissan prairie van won't start not even turning over just get a clicking sound would that indicate solenoid or starter motor


low cranks amps/voltage out of battery
loose battery terminals (earth or positive )
wire cable to starter solenoid faulty
poor connection at terminals and starter
starter relay
starter solenoid
starter motor itself

26222517-1rqsdozfiipimhxac415ohhu-2-0.jpg

26222517-1rqsdozfiipimhxac415ohhu-2-1.jpg

Jun 21, 2016 | Nissan Cars & Trucks

1 Answer

Starter


For step by step starter removal on your vehicle, with diagrams,Click the link below:----

Nissan Maxima Starter removal

http://technoanswers.blogspot.com/2012/11/nissan-maxima-starter-removal.html

==========
These will help.
Thanks.

Nov 28, 2012 | 1997 Nissan Maxima

1 Answer

How to remove starter


Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the or disconnect the following:

    Negative battery cable Engine under cover Starter harness connectors Starter motor

To install:
  1. Install or connect the following:

    Starter motor. Tighten the bolts to 22-27 ft. lbs. (30-36 Nm) on the 3.3L engine; to 37-45 ft. lbs. (61-69 Nm) on the 3.5L engine or to 33 ft. lbs. (45 Nm) on the 4.0L engine. Starter harness connectors Engine under cover Negative battery cable

Hope helps (remember rated this).

Aug 17, 2010 | 1997 Nissan Pickup

1 Answer

My Nissan Prairie wont start it only goes click


Did you try jupp starting the car?
Sounds like you have a low battery?

Mar 02, 2010 | 1990 Nissan Minivan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...