Question about Land Rover Discovery

Open Question

How do I disemable my 2000 range rover engine?

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 58 Answers

SOURCE: 2000 4.6 range rover suv

You require an unlock code/ security code from the dealer. This will consist of 4 numbers. You can then input this code into the door lock to clear imobiliser. You will have to do this every time until you have your remote replaced or repaired. There is a procedure for inputting the code. What the display through the window with the door closed. You need to turn key to unlock or lock (depends on model) until you see the display react to your input. Once this happens you are ready to input the code. If for example the code was 3241 and you have turned it 4 times to the unlock position (most likely) you would start by turning it 3 times to the unlock, 2 times to the lock, 4 times to the
unlock, 1 time to the lock, pause then unlock the car and start the engine. It sounds tricky but once you get the hang of it its not too bad. If when you start to input the code it starts locking and unlocking the central locking is is not accepting the code. The difficult bit is getting it to recognise you are inputting the code. The central locking will do nothing during the code entry. Best doing this when the light is fading as its easier to see the display in the dashboard. Thats it, all you've got to do now is find the code. Often on a card inside the owners service books if still around!!
Good Luck John

Posted on Dec 16, 2008

  • 5 Answers

SOURCE: online owners manual 2000 land rover range rover hse

Do a serch on Google for RAVE. This is the land rover workshop manuals. The owner manuals are included.
MickyDrew

Posted on Jul 25, 2009

clifford224
  • 1975 Answers

SOURCE: need the coil pack firing

Here's the information that you needed. i hope this helps and good luck.


clifford224_218.jpg

Posted on May 11, 2011

  • 1116 Answers

SOURCE: 03 Range rover "engine service

Try this:


Switch ignition OFF


Press and Hold left instrument panel reset button, switch ignition ON to position 1


Keep reset button pressed for approximately 5 seconds until the LCD displays "RESET SIA".


The distance to service and the service type " Inspection" will be displayed.


To reset distance the left hand button should be pressed before the 'RESET' message has

flashed 5 times. The LCD will display 'END SIA'. Switch ignition off


The timing to do this is must be about 5 seconds, if this is not working you can try again.

Posted on Jun 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I replace a water pump on a 2000 Land Rover Discovery 2 4.0 V8 engine?


How To Replace Water Pump On Discovery 2

www.roverparts.com > ENGINE > Cooling/Heating
See how you can replace the Land Rover Discovery 2 water pump on your own. ...Range Rover 4.0 or 4.6 (P38), 1995 Range Rover Classic, vehicles with 4.0 ...

Range Rover - How To Replace Water Pump P1 - YouTube

? 8:41
https://www.youtube.com/watch?v=EG1x6JZJ1cE
Jun 22, 2010 - Uploaded by RSW Solutions
How to Replace the Range Rover P38a GEMS motor water pump. ... Nathan Templeton 2 years ago ... I ..

Oct 30, 2015 | Land Rover Cars & Trucks

1 Answer

How do you enable a range rover engine when key battery is flat


There is a sequence of left and right turns of the key in the driver's door that will reset your bECM (Rovers brain) if the following have been tried.
1. Replace batteries in remote and 're-sync by depressing lock button on remote while physically turning and locking the door. Don't release button until locked and key removed. Repeat for unlock button.
2. Disconnect negative/earth cable from battery. While disconnected open driver's door, turn ignition to position 2, return to battery leaving driver's door open and reconnect the negative cable. Proceed to ignition. Turn off completely. Close all doors and hood and attempt starting.
Should both of these methods fail, run a search here on fixya for "engine disabled Range Rover P38" This will take you to step by step instructions on resetting the bECM which I opened this post with. It has been covered many times here, including by myself, no reason to post it again.
Good Luck!

Jul 14, 2014 | 2000 Land Rover Range Rover

1 Answer

Range rover wont start


Have you tried the sensor on the fly wheel that starts the fuel pump running when you turn the key,I had that problem the engine would turnover but not start ,had to put In a new sensor ,it cud red the problem but wasn't cheap!

Jun 20, 2014 | 2000 Land Rover Range Rover

1 Answer

I did a engine swap with a used engine i ve tryed everything but it wont start no spark i changed the cam and crank sensor but still nothing any ideras


Read this installation guide for carrying out any type of car engine's installation step by step with expert guidance here. The entire process is carried out in a simple and easy to follow procedure at
http://www.hiperformer.com/installation-guide.html
Here you will guidance from experts who have 37 years experience in the field.

Dec 09, 2012 | 2000 Land Rover Range Rover

1 Answer

My 2000 range rover keeps over heating


stuck thermostat low coolant bad radiator cap leaking water pump clogged radiator defective belts tension er worn out engine electric fan not working

Mar 16, 2012 | 2000 Land Rover Range Rover

1 Answer

I have a 2003 land rover range rover and the key will not turn to start the engine or to even move into nuetral, any suggestions?


sounds like your ignition lock cylinder is bad, you can try tapping on it with something for a little while and spray some WD40 in it to help loosin everything up

Feb 04, 2011 | 2000 Land Rover Range Rover

1 Answer

2000 Range Rover 4.6 serpentine belt diagram Belt slipped off, how do I fix it?


The big Belt for the AC,Cooling,Auternator etc. slept off. I stopped the car imediatly. Range Rover P38 1999. The Engine sounds still healthy. Will there be big damage after all?

Dec 13, 2010 | 2000 Land Rover Range Rover

1 Answer

How to disengage four wheel drive on 2000 range rover 4.0 SE always running on all four.


If there is no switch or lever, it is suppose to be permanent 4WD. Remove the short driveshaft connecting the front differential to the transmission/gearbox.

Phillip

Nov 20, 2009 | 2000 Land Rover Range Rover

1 Answer

2000 range rover code p1415 and p 1170


check the pins for pump of abs and make wd40

Sep 11, 2009 | 2000 Land Rover Range Rover

2 Answers

Online owners manual 2000 land rover range rover hse


Do a serch on Google for RAVE. This is the land rover workshop manuals. The owner manuals are included.
MickyDrew

Apr 07, 2009 | 2000 Land Rover Range Rover

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...