Question about Cars & Trucks

1 Answer

95 ford f 250 4x4 7.3l powerstoke diesel with direct injection replace fuel pump, filter canister, high pressure unit it starts and runs but all of a sudden it will just die with the top off the canister at the bottom of the canister fuel that comes mechanical pump has air bubbles coming out

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 42,131 Answers

Are you saying that the fuel filter is pressurising and blowing the filter apart. Please be more specific in what is happening and where are the air bubbles coming out of.

Posted on Nov 17, 2013

Testimonial: "The air bubbles are coming from the bottom of the canister. It has duel tanks .Im i having problems with the selector or the lines"

  • 1 more comment 
  • ropes mora Nov 19, 2013

    the air bubbles are coming from the bottom of the canister. it has duel tanks, am i having problems with my selector. or with my line's

  • Bill Boyd Nov 20, 2013

    remove the selector and connect directly to that tank check for air bubbles. If some then check that the pick-up in the tank is not cracked by filling right up and seeing if the bubbles are still there. Check all hoses are good and tight.If all ok then repeat the procedure for tha second tank. IF that is ok then the problem may be in the selector as that is the common unit that you removed.

  • Bill Boyd Nov 20, 2013

    If you have a hand promer on the filter it may be that is the problem as well

×

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: p1209,p1212,p0340,p0470,p1211

you should probably check your fuel pressure between the pump and the fuel bowl. my bet is that is is dropping pressure to zero causeing it to shut off just after it gets running. and there are several things that could cause that but the first to check is a return line valve on the side of the fuel bowl. that when pressure builds up it releases back into the tank and if it gets stuck open you will not have enough fuel pressure to run your truck. mine just did the same thing.

Posted on Oct 08, 2009

rickyrt441
  • 4399 Answers

SOURCE: I started it up one morning, it was running fine 4

Have you checked the fuel pressure on it? Fuse? Pressure to the engine?

Posted on Feb 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHY DOES MY ISUZU 4HL1 ENGINE HAVE A HARD START ALWAYS?


no car stated, huge NPR truck no less.
no year stated
so no free book information on that engine,.
big diesel. 4HL1, no dash letter?
compression at spec.?
glow plugs work.,
filters clean. water in fuel,
does test fuel (spray'd) help? ???
injection problems
lack of startup air.(filter)


The 4HL1 is a common rail direct injection OHC 16V high-pressure fuel injection system diesel engine of 4.777 L capacity with electronic control system. Peak torque is 333 Nm, peak power is 140 PS (103 kW) at 3,000 rpm. Maximum torque is (34.0 kg m)'/1,500 rpm. Bore is 115 mm, stroke is 115 mm.
The 4HL1-N is a common rail direct injection OHC 16V high-pressure fuel injection system diesel engine of 4.777 L capacity with electronic control system. Peak torque is 333 Nm, peak power is 131 PS (96 kW) at 3,000 rpm. Maximum Torque is (34.0 kg m)'/1,500 rpm. Bore is 115 mm, stroke is 115 mm.
The 4HL1-TC is a common rail direct injection OHC 16 V turbocharged and intercooled high-pressure fuel injection system engine of 4.777 L capacity with electronic control system. Peak torque is 425 Nm, peak power is 160 PS (118 kW) at 2,700 rpm. Maximum torque is (43.3 kg m)'/1,500 rpm. Bore is 115 mm, stroke is 115 mm.
The 4HL1-TCS is a common rail direct injection OHC 16 V turbocharged and intercooled high-pressure fuel injection system diesel engine of 4.777 L capacity with electronic control system. Peak torque is 500 Nm, peak power is 179 PS (132 kW) at 2,700 rpm. Maximum torque is (51.0 kg m)'/1,500 rpm. Bore is 115 mm, stroke is 115 mm.

May 31, 2016 | Isuzu Cars & Trucks

1 Answer

How do you bleed a diesel pump jeep Cherokee turbo diesel 3.1 5 cylinder 2001


we dont have this engine here, USA.
but i have the WG jeep book,
starting page 12 , chapter 14


FUEL INJECTION PUMP BLEEDING
(1) If the fuel injection pump has been replaced,
air should be bled at the overflow valve before
attempting to start engine.
(a) Loosen the overflow valve (Fig. 18) at the
rear of the injection pump.
(b) Place a towel below the valve.
WARNING: WHEN CRANKING THE ENGINE TO
BLEED AIR FROM THE INJECTION PUMP, THE
ENGINE MAY START. PLACE THE TRANSMISSION
IN NEUTRAL OR PARK AND SET PARKING BRAKE
BEFORE ENGAGING THE STARTER MOTOR.
CAUTION: Do not engage the starter motor for
more than 30 seconds at a time. Allow 2 minutes
between cranking intervals.
(2) Crank the engine for 30 seconds at a time to
allow air trapped in the injection pump to vent out
the fuel injector drain tubes. Continue this procedure
until the engine starts. Observe the previous WARNING
and CAUTION.
(3) Tighten overflow valve.
HIGH-PRESSURE FUEL LINE BLEEDING
WARNING: THE INJECTION PUMP SUPPLIES HIGH-
-PRESSURE FUEL OF APPROXIMATELY 45,000 KPA
(6,526 PSI) TO EACH INDIVIDUAL INJECTOR
THROUGH THE HIGH-PRESSURE LINES. FUEL
UNDER THIS AMOUNT OF PRESSURE CAN PENETRATE
THE SKIN AND CAUSE PERSONAL INJURY.
WEAR SAFETY GOGGLES AND ADEQUATE PROTECTIVE
CLOTHING AND AVOID CONTACT WITH
FUEL SPRAY WHEN BLEEDING HIGH-PRESSURE
FUEL LINES.
WARNING: DO NOT BLEED AIR FROM THE FUEL
SYSTEM OF A HOT ENGINE. DO NOT ALLOW FUEL
TO SPRAY ONTO THE EXHAUST MANIFOLD WHEN
BLEEDING AIR FROM THE FUEL SYSTEM.
Bleed air from one injector at time.
(1) Loosen the high-pressure fuel line fitting at
the injector (Fig. 19).
(2) Crank the engine until all air has been bled
from the line. Do not operate the starter motor
for longer than 30 seconds. Wait 2 minutes
between cranking intervals.
(3) Start the engine and bleed one injector at a
time until the engine runs smoothly.

end quote.
pump timing is on next page
or tank filter line priming before. above.

Mar 22, 2016 | Jeep Cars & Trucks

1 Answer

Ford F250 2002 7.3 Diesel won't start


check engine immobiliser and crank position sensor . Run fault codes and replace faulty units.

Apr 04, 2013 | Ford Cars & Trucks

1 Answer

SYSTEM WONT BLEED


diesel engines high pressure pumps not suppose run dry.diesel fuel keep high pressure pump cool and lubricated.problem could be fuel pressure regulator in the fuel filter water separator housing.replace fuel filter see if it helps problem could be fuel pressure regulator in fuel filter housing, the fuel pressure regulator has a air bleed orifice that allows vent to the fuel tank.make sure fuel pump fuse okay pump getting power. i would let garage or dealership check it out if all fails because your diesel engine fuel timing is pcm controlled if let fuel system go dry you probably have to have fuel injection timing reset or could have damage high pressure pump letting it run dry i hope thats not the case because high pressure pump not cheap part i hope it not that.

Sep 17, 2012 | 2008 Ford F-350 Super Duty

2 Answers

2006 ford f350 deisel turns over wont start unless i use starting fluid it then runs great. changed fuel filter oil filter and oil, wrench symbol came on went into engine fail safe mode, said something...


the diesel engine is a 6.0L or a 6.4L? because the 6.0L don't use electronic throttle control. they control the demand of diesel threw the high pressure oil system they have a sensor call injector pressure regulator. this sensor is responsible of maintain the proper pressure in the high pressure oil system so that the engine could start . i also suggest you to check if it is any leak on the high pressure oil system or if the low pressure system is delivering the pressure required for the high pressure system to work properly. to do that you most have a scan tool. also you can check the pressure of the diesel pump that its in the chassis to eliminate the high pressure oil system as the cause of your concern. if u don't have the proper gauges to check the pressure of the diesel pump you could remove the cap of the small fuel filter that is next to the oil filter remove the filter and put the ignition switch in the on position and see in the container if you have a fast or slow filling. if you encounter that the filling is too slow then your problem is with the fuel diesel pump that is on the chassis this pump is called HFCM, Horizontal Fuel Control Module

Jan 30, 2011 | 2006 Ford F 350 Super Duty

2 Answers

Need to know if ford has an in-line filter between fuel pump and filter mounted ontop of motor on f350 7.3 turbo diesel


yes, on engine.base part #9155, Item #40, big round thing in picture

SECTION 303-04C: Fuel Charging and Controls — 7.3L Diesel 2000 F-Super Duty/Excursion/Motorhome Chassis Workshop Manual
DESCRIPTION AND OPERATION Fuel Charging And Controls Fuel System
The fuel system used on the 7.3L direct injection (DI) turbo diesel engine is controlled by the powertrain control module (PCM) (12A650).
The fuel system components consist of:
  • electric inline fuel pump (9350).
  • high-pressure oil pump.
  • fuel filter (9155).
  • oil pressure regulator.
  • oil pressure sensor.
  • fuel pressure regulator (9C968).
  • high-pressure oil pump reservoir.
  • water in fuel switch/fuel heater thermostat.
Fuel System Components

5398a63.gif

Nov 03, 2009 | 2000 Ford F350 Super Duty Super Cab

1 Answer

2001 f350 diesel craks but wont start


SOUND LIKE THE ELECTRIC LOW PRESSURE FUEL PUMP CHECK FUSE TO SEE IF PUMP GETTING POWER. IF NOT REPLACE FUSE AND CHECK THE WIRE TO PUMP.IF PUMP IS GETTING POWER..REPLACE FUEL FILTER FIRST.IF IT DONT HELP.COULD BE THE ELECTRIC LOW PRESSURE PUMP. FAULTY. IT PUMPS DIESEL FUEL IT INTO INJECTION PUMP TO BE PRESSURIZED TIMED AND INJECT.SEE IF LOW PRESSURE PUMP DONT WORK THE WHOLE ENGINE WONT RUN.THE INJECTION PUMP NEED FUEL FROM LOW PRESSURE ELECTRIC PUMP TO RUN ENGINE.

Aug 11, 2009 | 2001 Ford F350 Super Duty SuperCab

2 Answers

2001 F350 7.3L Diesel won't start


I take it you have a crank no start issue, the fuel is injected by high pressure oil, no oil pressure no start, there are 2 oil pumps, low lube pressure and high injection control pressure (ICP) the injection system is hydraulic controls electric actuated fuel injection, if when you crank the engine over and the oil pressure guage goes up base pressure is ok, then its high pressure or the best thing I can say is pull codes and that can give me a good direction to send you in, there are many things that can cause that problem, if the fuel heater shorts out, the pcm and it are on the same 30amp circuit causin the same problem and still you would have proper fuel pressure readings.

Jul 13, 2009 | 2001 Ford F350 Super Duty SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...