Question about 2004 Chevrolet Impala

Open Question

Inner tie rod 2004 impala - 2004 Chevrolet Impala

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 9 Answers

SOURCE: chev avalanche 2004 inner tie rods

I was able to fix the inner tie rod problem with a little of patients and 90 bucks for the parts. When I took it in for the front end to be aligned the drivers side was only off by 1/4 on an inch.

Posted on Nov 08, 2008

Ad
  • 141 Answers

SOURCE: inner tie rods

if it is a rak and pionin sterring yes

Posted on Jan 13, 2009

Molson02536
  • 3854 Answers

SOURCE: how difficult to replace inner tie rod end on 06 silverado 2wd?

Not that hard, just spray the tie rod sleeve with WD40 night before and let it soak in. Remove the collier pin and and nut and hammer the old inner tie rod end out of the Track rod with a 5 pound sledge hammer. Remove the inner tie rod end from the sleeve and don't forget to mark the distance so you can place the new tie rod end at the same length. Reinstall the inner tie rod end to the Track rod and tighten the nut and replace the collier pin with a new one. Grease the fitting and go for a test drive, if the truck does not wonder then your good to go with out a alignment. Good luck and hope this helps, Note, make sure you have to right inner tie rod ends. Each side has different thread rotations.

Posted on Jun 03, 2009

  • 2309 Answers

SOURCE: idler arm LF,idler bracket LF,pitman arm LF,tie

you will need a pitman arm puller, tie rod separator and a good set sockets(6 point preffered)and some penetrating oil, measure all distances between points before removal,and get the vehicle aligned

Posted on Dec 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Inner tie rod removal with tool


One end of the tie rod is a left hand thread
make sure that you are turning it the right way

Apr 12, 2015 | 2005 Hyundai Tucson GLS

1 Answer

I have a 2006 impala LT & I don't know how to get


Disconnect the tie rod and it should come off. Is this the type which has a metal band clamp holding it in place? Cut the band. New part should come with new clamp band which (wait for it...) requires a special tool to install, but can often be fitted by careful use of dull side cutters or bull nose cutters.

Oct 13, 2014 | 2006 Chevrolet Impala

1 Answer

Replacing left side inner tie rod end


just unbolt it count rounds of taking the end off and screw new one on same amount will get you close on alignment

Apr 02, 2014 | 2004 Chevrolet Malibu Maxx

1 Answer

Inner tie rod boot and socket removal


get the right bits first,and buy a tie rod end removal tool,not too expensive..mark how many threads left before unwinding tie rod end off,so you can put it back same position

Jun 29, 2010 | 2004 Ford Freestar

1 Answer

How to install inner and outer tie rods on a 2004 Chrysler Pacifica - I waqs told buy a trusted local mechanic that I need to replace 3 of the 4 tie rods. Might as as well replace all 4, but how hard is it...


You will need to rent or borrow in inner tie rod tool but here are the directions.
1. Break the jam nut on inner tie rod to outer loose.
2. Remove nut from outer tie rod attaching it to steering knuckle.
3. Use hammer to get tie rod out of knuckle.
4. Unscrew outer tie rod then jam nut
5. Remove clamp from boot and slide off inner tie rod.
6. Using side cutter or hammer and chisel break off metal clamp on the inside of inner tie rod boot.
7. Using inner tie rod tool, unscrew inner tie rod from rack and pinion
8. Reinstall parts and have it aligned

May 06, 2010 | 2004 Chrysler Pacifica

1 Answer

How to replace inner tie rod dodge ram 1500 2004


Your going to need some pullers and some other tools your probably dont have just get it done professionally

Nov 21, 2009 | 2004 Dodge Ram

1 Answer

Can u tell me how to replace the outer tie rod on a 2004 pontiac grand am


Loosen the pinch bolt attaching it to the inner tie rod. Remove nut at the strut that attaches outer tie rod end to the strut.measure or count threads or turns it takes to spin out the outer tie rod end, reverse proceedure to install.

Sep 16, 2009 | 2004 Oldsmobile Alero

1 Answer

Cannot get the inner tie rod off


well you can take off the wheel and remove the outter tie rod end but there is a special tool like a long tube that you need to reach in the rack & pinion to loosen the inner tie rod end they can be bought at auzone i belive

Mar 26, 2009 | 2004 Mitsubishi Lancer

1 Answer

Chev avalanche 2004 inner tie rods


I was able to fix the inner tie rod problem with a little of patients and 90 bucks for the parts. When I took it in for the front end to be aligned the drivers side was only off by 1/4 on an inch.

Nov 07, 2008 | 2004 Chevrolet Avalanche

1 Answer

Inner tie rods


if it is a rak and pionin sterring yes

Jul 07, 2008 | 2004 Chevrolet Silverado

Not finding what you are looking for?
2004 Chevrolet Impala Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...