Question about 2000 Jeep Grand Cherokee

1 Answer

What is an error Code P1296 Jeep CHEROKEE 2000

What is an error Code P1296 Jeep 2000

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 46 Answers

It is a 'under 5 volts' error to the map sensor.

Posted on Jul 07, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 6982 Answers

SOURCE: 2000 jeep grand cherokee limited starts in 3rd gear

oil pressure problem should be checked independently of other problems...Use a good accurate mechanical gauge to check. If pressure is good (no less than 15psi at idle hot (I prefer to see at least 20) check dash grounding, block ground and if OK, change sending unit. Dash and body ground can influence operation of shift and body control modules so indirectly your problem may or may not be related, depending upon what you find while testing. And it could turn out to be a defective module! They are expensive and just plugging new ones in may work, but then again, it might not. I might be totally incorrect on this...that's the value of actually being there instead of doing this by "remote control".
If you read the numerous posts pertaining to all vehicles, you will see that you are not alone with electrical problems...As long as the engineers who design this stuff, keep using "modules" to replace ordinary simple and reliable systems, we will continue to have these problems. Do some testing and I'm sure you will find a solution! (I'm still waiting for someone to make a program for a PC that will give a complete readout of every system in a vehicle, including exact faults instead of general system "suggestions")
Good luck

Posted on Apr 07, 2009

maygemini
  • 147 Answers

SOURCE: Radiator fan will not turn off in my 2000 Jeep Grand Cherokee

usually the engine relay or cooling fan relay..!

Posted on May 08, 2009

peterrance19
  • 399 Answers

SOURCE: 1999 jeep grand cherokee, error code 1494

hi im pete ill try and help code 1494 is fuel sending unit dection fuel pump ,<ldp>. pressure switch hope this helps

Posted on Nov 19, 2009

BeninVa
  • 389 Answers

SOURCE: 2000 cherokee 6cyl 4.0 has given code p0432 and

Not necessarily, the catalyst monitor uses two oxygen sensors to monitor the operation of the converter. One or both of the sensors may need replacement. One tip, they are much easier to remove from a hot system, although the chance of a burn is greater.

Posted on Dec 31, 2009

  • 819 Answers

SOURCE: 2000 jeep grand cherokee scanner hook up

underneath the dash on the drivers side, poke your head under and look up. you will see it in that region.

Posted on Apr 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm working on the 2004 Jeep Grand Cherokee 4.7 showing error codes


lashes 52 and 54 ,you do mean flashes ? What flashes ? Check engine light doesn't flash codes .

Apr 24, 2017 | Jeep Cars & Trucks

1 Answer

Jeep grand Cherokee 2000 v8 runs 15min cuts off cools down 15 min run short time ( no errors)


probable a bad engine control computer if there is no code. could also be bad crankshaft positioning sensor, or camshaft positioning sensor.

Aug 21, 2014 | 2000 Jeep Grand Cherokee

1 Answer

What is the diagnostic code 02 for 6 cylinder 2000 jeep grand Cherokee laredo


use a real scan tool
only that works.
you need to see all jeep DTC error.s

Jul 23, 2014 | 2000 Jeep Grand Cherokee Laredo

1 Answer

Code p1296,p0108,p1494,p0500 on 2000 durango, what most likely wrong?


P1296 No 5-Volts to MAP Sensor
P0108 MAP Sensor Voltage Too High
P0500 No Vehicle Speed Signal Circuit
P1494 Leak Detection Pump Switch or Mechanical Faul
I would try MAP sensor first.

Mar 18, 2014 | Dodge Durango Cars & Trucks

1 Answer

What is an error Code P1296 Jeep CHEROKEE


The MAP sensor voltage is too low. The PCM regulates this voltage, but a short to ground or MAP sensor failure could bring this voltage down. So you need to check the wire bundle for chaving against some metal part. Known is a stud on the aft side of the head where a wire bundle passes.

Nov 17, 2013 | 2000 Jeep Grand Cherokee

1 Answer

What is an error Code P1296 JeepCHEROKEE 2000


5 volt reference voltage is missing to map sensor. broken wire, grounded wire, internal PCM fault.

Nov 17, 2013 | 2000 Jeep Grand Cherokee

2 Answers

I have a jeep grand cherokee i have a code p1296. voltage missing at throttle position sensor.explanation engine running and the ecm detected map sensor voltage less than expected. probable cause open or...


I would change the TPS throttle position sensor and the Map/MAF are you sure its not the mass air flow?. I think your computer is fine it could be have a loose ground issues but computers dont go bad.

Sep 12, 2011 | 1997 Jeep Grand Cherokee

1 Answer

What is code #code p1296


Definition of Diagnostic Trouble Code P1296 Audi: Cooling system malfunction Chrysler: No 5 volts to MAP sensor Dodge: No 5 volts to MAP sensor Ford: Injector Multiple Faults - Bank 2 Jeep: No 5 volts to MAP sensor Lincoln: Injector Multiple Faults - Bank 2 Mazda: Injector Multiple Faults - Bank 2 Mercury: Injector Multiple Faults - Bank 2 Mitsubishi: MAP Sensor 5-Volt Supply Fault Volkswagen: Cooling system malfunction

Jun 08, 2010 | Volkswagen Jetta Cars & Trucks

1 Answer

I HAVE A 2000 JEEP CHEROKEE AND THE ENGINE LIGHT CAME ON......THEN IT MADE A KNOCKING SOUND. EVERYTHING ELSE IS OK.THE OIL IS FINE THE COOLENT.....WHAT DO YOU THINK ?


Go to Checker, Autozone...or similar. Ask them to reset the check engine light and read the error code. There is no charge and its often something small. Spark plug misfire, fuel filter, PVC valve, or such.

Jan 19, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

243 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...