Question about 2007 Honda Odyssey

Open Question

Serpentine belt tensioner replacement odyssey

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: how does one remove the belt tensioner off a 2001 honda passport?

14 or 15mm socket to release tension. Use socket with leverage bar push/pull towards driver side. Will notice tension releasing, pull belt. Use 5/16 allen wrench for bolt in center, 12 mm socket for mounting bolt. Remove bolts, remove tensioner.

Posted on Jul 06, 2009

Ad
philschneide
  • 448 Answers

SOURCE: How do I loosen the tensioner to replace the

First, note how the drive belt is routed, then use a wrench on the tensioner pulley center bolt and turn the tensioner clockwise (four cylinder engine) or counterclockwise (six cylinder engine) to release the drive belt tension. Remove the drive belt from the tensioner and relax the tensioner. Fit the new belt on the other pulleys, then turn the tensioner again and fit the new belt over the tensioner.

The picture is from a different model, but it is similar to what you are working with.

ba64f9c.jpg
Hope this is helpful to you.

Posted on Dec 19, 2009

  • 3741 Answers

SOURCE: need to replace Serpentine belt and p/s belt on my

the procedure is as follows:-- You have to do it from underneath the vehicle. Take off the rivets to the two plastic covers, and then you will be able to see the tensioner for the belt. Use a 3/4 inch wrench on the tensioner (don't put it on the bolt that holds the tensioner on), and pull it toward the vehicle. The belt will loosen, and you can take it off. As a car owner, you know how important the belt tensioner is for your 2002 Honda Odyssey. However, internal parts wear and damage will loosen or seize the tensioner wheel, causing the belt to slip and make noise. Eventually, the belt may break, shut down the engine and lead you into a serious traffic accident. Before that happens, replace the tensioner on your Honda model and save yourself a lot of problems:---- Remove the Drive Belt:-- 1)Look for the drive belt routing diagram on your vehicle's engine compartment. This is a black and white label, about 4 by 6 inches, usually attached to the radiator shroud or near the strut towers inside the engine compartment. This diagram will be your guide when reinstalling the drive belt. If cannot find one, make a simple sketch on a piece of paper. 2) Insert a belt-tension release tool, or similar tool, into the auto-tensioner arm. 3)Rotate the auto-tensioner arm counterclockwise and slip the belt off the tensioner pulley. 4) Release the auto-tensioner but do not let it snap back in place. 5) Remove the drive belt from the engine compartment. Replace the Belt Tensioner 1) Unscrew the two auto-tensioner mounting bolts using a ratchet, ratchet extension and socket. Note the location of each bolt because they are of different size. 2) Remove the old auto-tensioner from the engine compartment. 3) Set the new auto-tensioner in place and start the two mounting bolts by hand. Make sure you install the bolts in their original place. 4) Start tightening the bolts until they hit the stop using the ratchet, ratchet extension and socket. 5) Torque the two bolts using a torque wrench. Torque the small bolt to 16-foot pounds [22 Nm] and the large bolt to 47-foot pounds [64 Nm]. This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

Posted on Mar 01, 2010

  • 94 Answers

SOURCE: How do I replace the timing belt on a 2007 Odyssey?

it is quite tough job for beginner but if you properly marked the position of the top dead centre, position of the pulley etc, it should be ok. remember any slight movement of the pulley will cause the engine to run erractically or cannot start at all.

Yes it is recommended to change the water pump, pully etc. as you mentioned

Posted on Apr 14, 2010

  • 1340 Answers

SOURCE: how can I replace the serpentine belt?

Tension pulleys are self adjusting.For a belt routing diagram,some local libraries have haynes repair manuals you can look at.A Honda dealer may give you a diagram free or low cost too.Good luck!

Posted on Jul 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2096 Honda Odyssey battery light flashes on (then goes off) when decelerating. Long story short, in the past month, to fix this issue, I have had the alternator replaced (twice), the serpentine belt...


the cowboys at the dealership worked on power stearing when they should have tightened the alternator belt cowboys honestly what people will do for money

Sep 02, 2012 | Cars & Trucks

1 Answer

Replacing serpentine belt on odyssey


I wouldn't disconect the batry just make sure the key is out of the vehicle so it can't be started by accident when you are working on it. Hint: Draw a diagram of the belt routing prior to removeing the belt.

Jun 28, 2012 | 2007 Honda Odyssey

1 Answer

Serpentine belt


Application:
With A/C


2.image

Kia_Sedona_2002-2006
Accessory Drive Belts

Print


Accessory Belt Routing



0996b43f802319a9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory serpentine belt routing-3.5L engine


0996b43f802319a9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory serpentine belt routing-3.5L engine


0996b43f8020700d.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory serpentine belt (A) routing-3.8L engine


Inspection

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.


Removal & Installation

  1. Disconnect the negative battery cable.
  2. Rotate the auto tensioner clockwise to release tension, then remove the drive belt.

To install:
  1. Install drive belt (A). Route the belt over the components in the following order: Crankshaft pulley - A/C pulley - idler pulley - generator pulley - water pump pulley - P/S pump pulley - tensioner pulley.
  2. Rotate auto tensioner arm in the counter-clockwise moving auto tensioner pulley bolt with wrench.
  3. After putting belt on auto tensioner pulley, release the auto tensioner pulley slowly.

    0996b43f802319a9.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Accessory serpentine belt routing-3.5L engine


    0996b43f8020700d.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Accessory serpentine belt (A) routing-3.8L engine


May 09, 2012 | 2006 Kia Sedona 3.8

2 Answers

Change serpentine belt on 06 sienna


  1. 1 Check to ensure the Sienna's engine is cold, then make sure the Sienna is in park, the ignition is in the off position and the key is removed from the ignition to prevent any possibility of the engine engaging during the serpentine belt replacement.
  2. 2 Open the hood and locate the serpentine belt routing diagram sticker on the side of the engine casing. Study it for a moment before removing the existing belt. It is essential the new belt be installed exactly as the diagram indicates.
  3. 3 Find the tensioner pulley, the main pulley that controls the serpentine belt, and fit a 1/2-inch socket wrench over the self-tensioner on the outside of the pulley.
  4. 4 Pull the wrench to the left to move the pulley forward, which loosens the belt, then remove the belt.
  5. 5 Compare the old serpentine belt with the new, replacement belt for length, width and number of grooves on the belt's underside. Be certain the replacement belt is the right part.
  6. 6 Fit the new belt on to each pulley according to the serpentine belt routing diagram on the manufacturer's sticker, or according to the drawing made prior to removing the old belt. Fit the new belt on to the tensioner pulley last, again applying pressure on the pulley's self-tensioner with the half-inch socket wrench to loosen the pulley.
  7. 7 Release the pressure on the self tensioner and allow the tensioner pulley to ease back into place, thereby tightening the new serpentine belt with the appropriate tension.
  8. 8 Remove the wrench and close the hood.
Thank you and good luck,
Lee

Aug 26, 2010 | 2006 Toyota Sienna

1 Answer

How do i release the tension belt ... cant seem to find bolt being referred to in other docs


Here's the procedure on how to release and replace the tension belt of your car.

Step 1
  • Open the hood on the Volvo S-60 and find the serpentine-belt routing diagram. The diagram should be attached to the top of the fan shroud that covers the radiator. If not, draw out the exact routing method of the serpentine belt around each pulley with a pen and a piece of paper.
  • Step 2 Locate the serpentine-belt tensioner that is in the very center of the engine. The tensioner will have a square bolt head in the center of the tensioner pulley.
  • Step 3 Slide the open end of the 5/8-wrench onto the square bolt head in the center of the belt-tensioner pulley. Turn the tensioner pulley counterclockwise and slide the serpentine belt off of the tensioner pulley.
  • Step 4 Remove the serpentine belt from the other pulleys and pull the belt out of the engine compartment.
  • Step 5 Slide the new serpentine belt into the engine compartment and around the crankshaft pulley.
  • Step 6 Route the new serpentine belt around each pulley. Turn the belt-tensioner pulley counterclockwise again and slide the serpentine belt around the tensioner pulley. Release the tensioner and it will tighten the belt around the pulleys. Look over the belt to ensure that it is inside of each pulley.
  • Step 7 Crank the S-60 and look over the serpentine belt with the motor running. Let the engine run for about one minute and shut the engine off. Close the hood.
  • Aug 12, 2010 | 2001 Volvo S60

    1 Answer

    Replacing serpentine belt


    Click on the following direct Link. It has the Serpentine Belt Diagram that you will need depending on your engine size (2.0L or 3.0L) and your options (AC/No AC ect.).
    http://www.2carpros.com/car_repair_information/year/2001/make/mazda/model/tribute/2001_mazda_tribute_drive_belt_routing_diagram.htm

    Standard Rules to Removal the Serpentine Belt with a Tensioner:
    1. Find the Tensioner(s). (See Diagrams on Link)
    2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
    3. Remove the loosened belt off one of the other more easily accessed Pulleys.
    4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.


    Standard Rules for Installing the Serpentine Belt with Tensioners:
    a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
    b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
    c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
    d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
    e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

    Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

    Mar 23, 2010 | 2001 Mazda Tribute

    1 Answer

    Need to replace Serpentine belt and p/s belt on my 2002 honda odyssey is this complicated?


    the procedure is as follows:-- You have to do it from underneath the vehicle. Take off the rivets to the two plastic covers, and then you will be able to see the tensioner for the belt. Use a 3/4 inch wrench on the tensioner (don't put it on the bolt that holds the tensioner on), and pull it toward the vehicle. The belt will loosen, and you can take it off. As a car owner, you know how important the belt tensioner is for your 2002 Honda Odyssey. However, internal parts wear and damage will loosen or seize the tensioner wheel, causing the belt to slip and make noise. Eventually, the belt may break, shut down the engine and lead you into a serious traffic accident. Before that happens, replace the tensioner on your Honda model and save yourself a lot of problems:---- Remove the Drive Belt:-- 1)Look for the drive belt routing diagram on your vehicle's engine compartment. This is a black and white label, about 4 by 6 inches, usually attached to the radiator shroud or near the strut towers inside the engine compartment. This diagram will be your guide when reinstalling the drive belt. If cannot find one, make a simple sketch on a piece of paper. 2) Insert a belt-tension release tool, or similar tool, into the auto-tensioner arm. 3)Rotate the auto-tensioner arm counterclockwise and slip the belt off the tensioner pulley. 4) Release the auto-tensioner but do not let it snap back in place. 5) Remove the drive belt from the engine compartment. Replace the Belt Tensioner 1) Unscrew the two auto-tensioner mounting bolts using a ratchet, ratchet extension and socket. Note the location of each bolt because they are of different size. 2) Remove the old auto-tensioner from the engine compartment. 3) Set the new auto-tensioner in place and start the two mounting bolts by hand. Make sure you install the bolts in their original place. 4) Start tightening the bolts until they hit the stop using the ratchet, ratchet extension and socket. 5) Torque the two bolts using a torque wrench. Torque the small bolt to 16-foot pounds [22 Nm] and the large bolt to 47-foot pounds [64 Nm]. This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

    Mar 01, 2010 | 2002 Honda Odyssey

    1 Answer

    Removing old serpentine belt


    Hi alin,

    No prybar necessary.
    • Get a 14mm or 9/16" socket and a long handled ratchet or breaker bar.
    • Get the belt around all the pulleys except the A/C compressor or Alternator.
    • The tensioner pulley is on a spring loaded arm. Get your socket on the center nut of this pulley.
    • Slowly pull the ratchet toward the center of the engine. The pulley will pivot on the arm allowing you to get the belt on the final pulley.
    • Slowly release the tension.
    • You're done
    Mike

    Nov 17, 2008 | 2002 Honda Odyssey

    5 Answers

    Serpentine belt replacement


    2.0L Engines
    See Figures 11, 12 and 13
    The accessory drive belt for 2.0L engines has no provision for manual belt adjustment, since these engines use an automatic belt tensioner. Drive belt slack is taken up by the automatic tensioner.
    Movement of the automatic tensioner assembly during engine operation is not a sign of a malfunctioning tensioner. This movement is the tensioner self-adjusting and is required to maintain constant belt tension.
    The belt tensioner has a belt length indicator. If the indicator marks are not between the MIN and MAX marks, the belt must be replaced.
    0900c1528008d836.jpgFig. 11: Drive belt routing-2.0L SOHC engine with A/C 0900c1528008d837.jpgFig. 12: Drive belt routing-2.0L SOHC engine without A/C 0900c1528008d838.jpgFig. 13: Drive belt routing-2.0L DOHC engine

    Jul 24, 2008 | 1999 Ford Escort

    Not finding what you are looking for?
    2007 Honda Odyssey Logo

    Related Topics:

    71 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    yadayada
    yadayada

    Level 3 Expert

    77202 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22265 Answers

    Kevin Daniels

    Level 3 Expert

    1455 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...