Question about Chevrolet Cars & Trucks

Open Question

How to remove rear seat of a 15 passenger Chevy Van

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 508 Answers

SOURCE: rear seat removal on 1988 full size 2dr chevy blazer

The rear seat is bolted to the floor either from the inside or the outside. If attached from the undercarriage you will need to locate the rubber plugs that cover the bolt head or the hex nuts to the seat. Just remove these and the seat will come out.

Posted on Feb 07, 2009

  • 41 Answers

SOURCE: Remove seat from second row in Honda Mini Van 2007

on the passenger side feel under the seat and there is a lever that pulls toward you as you stand at the sliding door.

First, raise the armrest, then lower the back all the way forward. Then remove the headrest sit it out of the way and while pulling the lever under the seat towards you, lift up the seat from the back so it tilts forward. When it is standing on its "nose" lift first one side shifting it either forward or backwards to clear the rod on which it is hooked. Do the same with the other side of the seat and then lift it out. Installation is the reverse of removal.

The other seat is much the same, though sometimes the lever is a little different but in the same place.

Good luck,
bob

Posted on Jun 09, 2009

smartr10U
  • 1305 Answers

SOURCE: remove rear seat impala2007

To remove the rear seat, pull up on the front of the seat bottom, it should be hooked in place by spring type clips. After you get the front edge up, pull out the seat. This should expose the bolts/screws that hold the seat back in. Look below and there should be a couple of screws holding the seatback to the car body. Remove these and then you can pull the seat back out of the car.
K

Posted on Aug 29, 2009

  • 12104 Answers

SOURCE: 2004 chevy 3500 express passenger van transmission

if ur replacing it remove front grill disconnect both lines and carefully remove retaining clips from radiator if replacement is original eguipt mount & reconnect --if its a universal follow instructions usually cut off fittings and use clamps and hose to hook up

Posted on Oct 27, 2009

duane_wong
  • 6826 Answers

SOURCE: I need to remove the

REMOVAL & INSTALLATION 1983-86 Models

  1. On 4-door sedan, remove the package tray and vent duct.
  2. On hatchback, remove the speaker grilles.
  3. Disconnect the brake line from the wheel cylinder. CAUTION
    Brake fluid contains polyglycol ethers and polyglycols. Avoid contact with the eyes and wash your hands thoroughly after handling brake fluid. If you do get brake fluid in your eyes, flush your eyes with clean, running water for 15 minutes. If eye irritation persists, or if you have taken brake fluid internally, IMMEDIATELY seek medical assistance.
  4. Remove the brake line from the brake hose.
  5. Disconnect the brake hose from its bracket on the shock absorber.
  6. Loosen, but do not remove, the nut holding the suspension support to the shock absorber.
  7. Unbolt the shock absorber from the rear arm.
  8. Unbolt and extract the shock absorber from the body. To install:
  9. Attach the shock absorber to the body and tighten the 3 nuts to 17 ft. lbs. (25 Nm).
  10. Engage the shock absorber bracket with the carrier and install the hardware. Tighten the nuts to 119 ft. lbs. (162 Nm).
  11. Tighten the center suspension support nut to 36 ft. lbs. (49 Nm). There is a bearing located under the suspension support dust cover. Remove the dust cover and pack the bearing with multi-purpose grease. Once packed, reinstall the dust cover.
  12. The remainder of installation is the reverse of removal. Tighten each component to specifications.
  13. Have the rear wheel alignment checked.
1987-88 Models
  1. On wagon models, remove the toneau cover holder.
  2. Loosen the rear wheel lug nuts, raise the rear of the vehicle and support it safely. Block the front wheels.
  3. Remove the rear wheels.
  4. Using the proper size flare nut wrench, disconnect the backing plate hardware.
  5. With a flare nut and a back-up wrench, disconnect the brake tube from the brake hose and use a small plastic container to collect the brake fluid.
  6. Undo the clip and disconnect the brake hose from the shock absorber. NOTE: Before the axle bolts are removed, the axle carrier must be supported with a jack.
  7. Support the axle carrier with a floor jack and remove the mounting bolts and nut. Disconnect the axle carrier from the shock absorber.
  8. Support the shock absorber firmly by hand and remove the three mounting nuts. Remove the shock absorber from the body. To install:
  9. Position the shock absorber onto the body and support it firmly by hand. Install the three nuts and tighten them to 23 ft. lbs. (31 Nm).
  10. Attach the axle carrier to the shock absorber with the nuts and bolts. Tighten the nuts to 166 ft. lbs. (226 Nm).
  11. The remainder of installation is the reverse of removal. Tighten each component to specifications.
  12. Bleed the brake lines as described in Section 9.
  13. Have the rear wheel alignment checked.
1989-96 Models
  1. On the 4-door sedan, remove the package tray and vent duct. On 1992-96 models, it will be necessary to remove the rear seat back.
  2. On the hatchback, remove the speaker grilles.
  3. On the wagon models remove the tonnue cover and rear seat back.
  4. Loosen the rear wheel lug nuts, raise the rear of the vehicle and support it safely. Block the front wheels.
  5. Remove the rear wheels.
  6. Disconnect the brake hose and the ABS speed sensor from the shock absorber.
  7. If equipped with ABS, disconnect the Load Sensing Proportioning Valve (LSPV) spring from the lower arm.
  8. Disconnect the stabilizer bar link from the shock absorber.
  9. Support the rear axle and loosen the 2 bolts from the lower end of the shock absorber.
  10. From inside the vehicle, unbolt the upper support. Fig. 1: A rubber cap covers the rear shock absorber tower nut 89558p01.jpg
    Fig. 2: The upper shock absorber tower is retained by the center nut (circled) and three surrounding nuts 89558p02.jpg

  11. Lower the rear axle carrier and remove the two bolts.
  12. Remove the shock absorber from the vehicle. To install:
  13. Install the shock absorber assembly onto the vehicle.
  14. Connect the brake hose and the ABS speed sensor to the shock absorber.
  15. Connect the stabilizer bar link to the shock absorber.
  16. Install the wheel and tire assembly.
  17. During installation, please observe the following tighten specifications:
    1. Tighten the shock absorber-to-body bolts to 29 ft. lbs. (39 Nm).
    2. Tighten the shock absorber-to-axle carrier nuts to 166 ft. lbs. (226 Nm) on 1988-91 vehicles and 188 ft. lbs. (255 Nm) on 1992-96 vehicles.
    3. Tighten the suspension support-to-shock absorber nut to 36 ft. lbs. (49 Nm) on 1988-91 vehicles. On 1992-96 models, tighten the stabilizer bar link to shock absorber retainers to 47 ft. lbs. (64 Nm).
  18. Install the rear seat back, vent duct and the package tray as required.
prev.gif next.gif

Posted on Dec 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove bolt covers for front seats on 01 ford taurus


Identify and Remove bolt covers - Instructables

https://www.instructables.com/...remove...seats/.../Identify-and-... InstructablesNext slide both seat forward as far as they can go, and lean the back of the seat forward as well. Find the two bolt covers and remove them as well.

How To Remove Front & Rear Passenger Seats 2006-11 ...

? 15:30
www.youtube.com/watch?v=qCLx3Ak2BvY
Jul 31, 2013 - Uploaded by TheTongMan Here is a tutorial on how to remove the front passenger seat and the rear ... what pieces of equipment are you ...

Oct 21, 2015 | Ford Cars & Trucks

1 Answer

'96 chevy express van 1500...location of M A P sensor on 5.0 litre


1996 Chevrolet Truck G10 1/2 ton Van 5.0L SFI 8cyl

The MAP Sensor is located: Front seating area, center, under engine cover, rear passenger side of intake manifold, above valve cover, mounted on bracket.Here's a link to what it look's like Brad. MAP Sensor at AutoZone com Best MAP Sensor Parts for Cars Trucks SUVS

Jul 23, 2015 | Cars & Trucks

1 Answer

Exactly where under the hood of a '95 Chevy G20, van do you disconnect the rear ABS PUMP?


The ABS module is not under the hood.It is under the van floor on the passenger side at about the middle of the van.Slide under the Van at the passenger side cargo door and look up.

Feb 27, 2015 | 1995 Chevrolet G20

1 Answer

I have a 2008 Chevy Uplander... I cant seem to get power to the overhead power box in order to open the rear windows. I was told there is a power wire under the passenger seat... how would I access th


You have to take out passenger seat ! Four nuts or bolts hold it down. Push seat back all the way to get front fasteners and front to get back ones .Does vehicle have carpet ? Under seat is a connector X308 (23 cavities ) yellow wire pin K .

Nov 13, 2014 | 2008 Chevrolet Uplander

1 Answer

How do you remove the back seat from a 1994 chevy g20 van?


I believe the seats are bolted to the floor of the van. Make sure you unplug all electrical connections before removing the seats.

Feb 11, 2014 | 1994 Chevrolet G20

2 Answers

How to remove the headrests from the driver and passenger seat of a 2007 Chevy Uplander?


Remove the storage tray from the back of the driver and passenger seats. This can be a trick in itself. You have to squeeze together some body style clips with needle nose pliers going in from the bottom where the tray section meets the seat fabric. When you get the right and left hand side clips free the tray panel should just tilt out at bottom. Then just slide the whole tray panel up and then you can pull it out. Now you can get to the head rests. From the inside of the seat you can see the 2 head rest posts that connect to the cushion portion of it. Follow the 2 posts up until you see the black plastic sleeves they slide in. Take some channel locks and grab the black sleeves and turn them (they only turn one way) until the cut outs in the bottom of the sleeves are facing the front and rear of the van rather than the right and left sides. Once these are turned you can easily lift the whole head rest out.

May 26, 2011 | 2007 Chevrolet Uplander

1 Answer

I recently purchased a used 03 Chevy Venture van. The passenger sliding door doesn't open. It worked for 1 week and stopped. The driver side sliding door has a broken handle so I'm able to open that door...


Pain but fixable. Sounds like the linkage is not connected. Even a mechanic will have to remove the door panel and fight with it. If you can remove the rear seat from the drivers side side door then you might have room to remove the passenger side door panel to fix it. Usually clips are the first thing to break on door handle/latch linkages

Apr 06, 2010 | 2003 Chevrolet Venture Passanger

1 Answer

Change starter 2005 chevy van express


first disconnect batt positive. jack vehicle up on passenger side. you can see starter at rear of engine. you may have to remove plastic around bellhousing to remove starter. There are two bolts holding starter in place.usually 15 mm socket. there is a small nut holding wire. 5/16 or 11/32 socket.. remove it. large nut usually 13mm socket. once removed just reverse procedure. leave comment if successful.

Mar 21, 2010 | 1999 Chevrolet C2500

2 Answers

2004 chevy 3500 express passenger van transmission


if ur replacing it remove front grill disconnect both lines and carefully remove retaining clips from radiator if replacement is original eguipt mount & reconnect --if its a universal follow instructions usually cut off fittings and use clamps and hose to hook up

Oct 27, 2009 | 2004 Chevrolet Express

4 Answers

1976 VW Van Battery


The battery should be under the front passenger seat. Move the seat forward as far as it will go, and you'll see a metal plate (may be under the carpet), which comes off with four Phillips screws. To actually get the battery out, you will need to remove the seat.

Aug 05, 2008 | 1986 Volkswagen Wagon Camper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...