Question about 1993 Toyota Tercel

Open Question

Where do I check and add automatic transmission fluid? And what type transmission fluid?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
shaggyrat
  • 1224 Answers

SOURCE: Adding Transmission Fluid

there are 2 colored dip sticks one black (oil) one red (trans)
he means the one far in the back of the engine which is usually red

Posted on May 20, 2008

Ad
raycrazek
  • 106 Answers

SOURCE: landcruiser auto transmission,,how to check fluid level

when you open your hood look in the back of the motor on the left side.. you should see a stick with a circle on the end of it for your finger have you vehicle running warmed up that means let it run for 10 or 15 min. and then pull the stick out.. wipe it off real good. stick it back in all the way.. pull it back out and hold it horizontally and check it.. it's sometimes hard to read because it has bubbles on it.. try it a couple of times to get an accurate reading good-luck ray

Posted on Jan 16, 2009

ourhowse
  • 2007 Answers

SOURCE: NEED TO ADD TRANSMISSION FLUID BUT CANT FIND A SPOT TO ADD

Into the dipstick tube.

Posted on May 21, 2009

emissionwiz
  • 76848 Answers

SOURCE: 96 Toyota Corolla

the fill pluig is on the side of the transmission case, to access this you must jack the car up and crawl under it to see the plug

Posted on Jun 29, 2009

agent91
  • 2100 Answers

SOURCE: Automatic Transmission Fluid Level

Some cars, and some Toyotas don't have dipsticks, they have plugs on the right side of the tranny, the lower one is the level, some get checked while running, some don't. If the fluid seeps out, it is full, if it doesn't, you take off the top plug and fill till the fluid comes out the bottom hole. If you can't find it in your manual, check out Toyota.com, or Toyotanation, they have forums for your vehicle. Toyota is pretty good about their trannys, they don't even recommend changing the fluid, and the gears are tumbled for de-burring when new, no filings in the fluid. check it out.

Posted on May 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Transmission whines when cold and shifts on the edge


Sounds like it maybe slipping, try checking the transmission fluid level and add as necessary to full mark of near full mark, which is in the operating range, could do what I did with my windstar minivan, add in the Lucas Transmission Fix, for your Ford Taurus you'll need Mercon ATF ( Automatic Transmission Fluid ) unless its a manual transmission or differently specified which then will need different fluid, check the owners manual, repair manual or phone Ford and ask them for transmission fluid type. Keep in mind that the wrong fluid type in transmission and or wrong amounts ( overfilled ) or ( underfilled ) can affect the transmission's proper operation.


Also check your coolant, when coolant level is low the light will come on the dash cluster and add as needed, Fords usually use the green coolant,green colored coolant or could use the universal type coolant. Check the owners manual, look in a repair manual or ask Ford technician for the coolant type.

Jan 24, 2014 | 1999 Ford Taurus

1 Answer

How many qts of oil do i need


Depends on your engine.

1980 JEEP CJ-7 2.5L 4-cyl Engine Code [B]
CAPACITIES
Engine, GM without filter..........2.4 quarts[1]
Wix Filter ........ 51040
Cooling System, Initial Fill..........8.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....25 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 4.2L 6-cyl Engine Code [C]
CAPACITIES
Engine, without filter..........5.0 quarts[1]
Wix Filter..... 51522
Cooling System, Initial Fill..........11.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....30 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 5.0L 8-cyl Engine Code [H]
CAPACITIES

Engine, without filter..........4.0 quarts[1]
Wix Filter..... 51258
Cooling System, Initial Fill..........13.0 quarts
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A904, 30RH..........7.0 quarts
3 speed A999, 32RH..........8.4 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

Oilman

Feb 02, 2013 | 1984 Jeep CJ7

1 Answer

How much transmission fliud to use in my 02 intrepid


CAPACITIES
Automatic transmission, 42LE Initial Fill..........4.6 quarts [1]

automatic transmission, Total Fill
4 speed 42LE..........9.3 quarts
Differential, Front..........1.5 pints [2]

1. With ENG at operating temperature, shift through all gears. Check fluid level in PARK and add fluid as needed.

2. 42LE transaxles built after 7-26-99 fill to 3/8" (9mm) below fill hole.

Hope This Helps.

********Make sure that you use the recommended type flluid ATF+4, as there are several types available. Using the wrong type of fluid will damage your transmission********

Feb 26, 2011 | 2002 Dodge Intrepid

2 Answers

What type of trans. fluid does it take and how do i know when its full


Transmission Fluid Fluid Level Checking & Filling To Check:
  1. Connect a scan tool to the vehicle to read ATF temperature. ATF checking temperature should be 95° - 113°F (35° - 45°C).
  2. Start the engine.
  3. Raise and safely support the vehicle.
  4. Place a drain pan under the transmission.
  5. Allow the ATF temperature to reach 95° - 113°F (35° - 45°C). Automatic transmission fluid inspection plug vw-07-00-7273.gif

  6. Remove the inspection plug from the transmission housing. Fluid is pipe will run out. If fluid continues to drip out, no additional fluid is needed. If only the fluid in the overflow pipe runs out, additional fluid is needed.
To Fill:
Automatic transmission fluid filler pipe vw-07-00-7274.gif

  1. Pry the cap from the filler pipe. The cap locking device will be destroyed during removal.
  2. Pull the plug from the filler pipe.
  3. Add fluid slowly with VAG 1924 or equivalent until fluid runs out of the inspection hole. Install the inspection hole plug.
  4. Install the plug in the filler pipe and secure with a new cap.

Jan 28, 2011 | 2000 Volkswagen Jetta TDI

1 Answer

2001 Passport with automatic has no dipstick for transmission, how do I check level and where do I add fluid


If you are looking to check the fluid levels and add transmission fluid you will need to first purchase a fluid pump at your local car repair store. Most run between $10 and 25$. For best results, run your car for a few minutes to bring the fluids to operating temperatures before attempting to add fluid. Be careful of hot surfaces and liquids.
It is difficult to check the level of fluid in the 2001 Honda passport because it lacks a dipstick. Instead, you will have to get underneath the car and check it at the Automatic Transmission fluid pan. This is located approximately below the center of the rear passengers seat on the underside of the car.
To check the fluid, remove the top most bolt on the automatic transmission fluid pan (most use a 3/4 inch socket). Use your finger or other object to see if the fluid level is at the same level as the drain plug. This can be difficult to do therefore it may be easier to add fluid until it is full to verify that you are at the correct levels.
To add fluid, remove the top most bolt on the automatic transmission fluid pan (most use a 3/4 inch socket). Using the fluid pump, slowly add transmission fluid until it starts to drip out. Replace the bolt. Take care not to over tighten the bolt.

If you want to be thorough, start your car and while your foot is on the brake, run your transmission through the gears slowly. Turn off your car. Remove the fill bolt and check the fluid level again. If it is not full see the previous steps. If your levels are OK, replace the bolt and you are good to go.

Jan 20, 2010 | 2001 Honda Passport

2 Answers

How do i add fluid too the automatic transmission


Use a funnel and you add the fluid right thru the dipstick tube. Try not to overfill if you can this can cause the transmission to slip.

Nov 20, 2009 | 1990 Ford Probe

2 Answers

Wheni drive Geo Metro 1997 over 1 hour the transmission does not work.


Does your car have an automatic transmission? If so start by checking the fluid level. There will be a dipstick in engine compartment that is for the transmission. This you will have to do by having the engine running and transmission in park. Pull dipstick out and check were the reading is on the dipstick. If it is low add transmission fluid. Note: Check owners manual for the correct type of fluid that should be used for your cars transmission. I have included a link that will help you with doing this procedure. http://www.ehow.com/video_104_check-automatic-transmission.html
If this doesn't help there are bigger problems going on inside the transmission. And if your car is using transmission oil you should get the leak checked out. I hope hope that this is helpful.

Oct 30, 2009 | 1997 Geo Metro

2 Answers

I have a leak in my 97 automatic subaru legacy and need to add some fluid to my transmission just to get it to a shop. It doesn't say in the manual or on any site I've been to where to add it or what kind...


The type best used is "Genuine Subaru Automatic Transmission Fluid Type-HP or IDEMITSU ATF HP. you add it through the dip stick hole. You may also wish to add a transmission leak oil to swell the gaskets and stop the leak add it the same way if you choose to use it. both of these should be available at your local auto parts store like NAPA. Raz,...

Aug 21, 2009 | 1997 Subaru Legacy

3 Answers

Where do you fill the automatic transmission?


If you have a tranny dipstick, then you would need a long tranny type funnel and fill there.
If you do not have a dip stick, then you would have to raise the vehicle, and look at the tranny. There will be a higher and a lower plug on it. Remove the higher plug and stick your finger in the hole. If you feel fluid, then it is full.

Aug 02, 2009 | 2007 Chevrolet Cobalt Coupe

2 Answers

Where is the filler cap for the transmission on a suzuki vitara v6 automatic ?


You add A/T transmission fluid at the same place you check it. 
Same place you check the A/T fluid level. You add fluid at the same location.

Mar 06, 2009 | 2002 Suzuki XL-7

Not finding what you are looking for?
1993 Toyota Tercel Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...