Question about Toyota HiAce

Open Question

Hardly to engage reverse gear - HiAce Toyota Cars & Trucks

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75822 Answers

SOURCE: Reverse engages HARD!!!

Check for trans codes then I would suggest a fluid change if there are no trouble codes, many times these kinds of problems are caused by a little piece of dirt causing a shift solenoid to stick.

Posted on Aug 25, 2008

  • 176 Answers

SOURCE: My 2004 ford ranger xlt 4x4 won't go into any

Sounds like the forward clutches and/or low-reverse one-way clutch. Either way it sounds like it's time for an overhaul

Posted on Jul 09, 2009

consaka
  • 661 Answers

SOURCE: I cannot engage the 1st and 2nd gear while i can

Ok I see a manual transmission with a hydraulic clutch.
Get some fluid in that reservoir before you burn up the synchronizers.
Basically your clutch isnt disengaging because you are out of fluid. Next you need to find where the fluid is going. Likely the clutch slave cylinder is leaking and needs replaced. Pretty easy actually if you are handy with a wrench.

Posted on Mar 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hard reverse engaugment


have you checked the hydraulic fluid chamber on the firewall close to the brake fluid area? If it is low the clutch plate may not be engaging for reverse gear.

Jun 09, 2014 | 2007 Mazda B4000

1 Answer

C3 picasso can jump out of reverse if not rammed in hard


Transmission problem. I suggest getting it serviced or put a new transmission in it

Mar 18, 2013 | Cars & Trucks

2 Answers

Car goes into reverce but does not engage completely works fine in forward, when in reverce it seems lik it wants to ingage but does not. it makes a chattering sound and feeling. what electric part puts...


Hello. As you know, the transmission is one of the more sophisticated components in any auto. It takes the most transmission pressure to engage reverse, third, and fourth gear in an auto tranny. In an auto tranny, the shifter is connected to a linkage that manually shifts between the different gears in the transmission. When you shift into reverse, all transmission pressure is concentrated to engage reverse. When you shift to drive the transmission will operate normally, building pressure until it can shift into the next gear. With third, second, or first gear selected it will lock out all higher gears (Unless the TCU detects overrevving of the engine, in which case it will override gear selection and upshift to avoid engine damage). All the TCU does in a modern auto tranny is control shift points. Years and years ago, shifting was controlled by a spring attached to the gas pedal. When the gas pedal was depressed, the spring would expand. As tranny pressure grew, the spring would become compressed until it was fully compressed, engaging the next gear. The harder you stepped on the gas, the longer you went until the tranny shifted. In modern transmissions the TCU dictates shift points, and not much else. The TCU will also control when the torque converter will lock, but that's where it's duties end. The problem with engaging reverse is either a linkage issue, or a problem with the pump not building enough pressure to fully engage reverse.

Try putting the shifter in reverse, holding the brakes firmly, and giving the car gas. If the car reaches a higher RPM and suddenly slams into reverse it is the pump. The pump will only build enough pressure to engage reverse with higher RPM's. If the pump is severly damaged it won't engage at all, but if this is the case it probably won't engage third or fourth gear either at that point. If the problem is with the linkage, reverse just won't engage whatsoever, despite RPM's. I'd say start with the shift linkage. If it's bent or misadjusted it could cause reverse to not be fully engaged. The TCU doesn't control reverse at all, since there are no shift points and no need for the torque converter to lock.

Nov 20, 2009 | 2007 Saturn Aura XR Sedan

2 Answers

Hard to get into reverse


try shifting in to first and then reverse. reverse might be worn out. you can have that gear replaced without replacing the whole transmission.

Jun 19, 2009 | 1998 Jeep Wrangler

1 Answer

My Ford Escort van W reg. which I have just purc hased has problems with stiff gears particularly into reverse.


One of the most common causes of hard shift is the clutch no fully disengaging, also do you put it in 2nd before you try 1st or reverse, it helps stop gear motion in the trans which eases the effort to engage the non-synchro gears, which first and reverse are most likely.

Sep 11, 2008 | Ford Escort Cars & Trucks

1 Answer

Reverse engages HARD!!!


Check for trans codes then I would suggest a fluid change if there are no trouble codes, many times these kinds of problems are caused by a little piece of dirt causing a shift solenoid to stick.

Jul 15, 2008 | 1995 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...