Question about 2001 Ford Focus

Open Question

2000-2004 Ford Focus 2.0L Dohc Heater Hose Coolant Tube Ys4Z-8290-Ba

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 507 Answers

SOURCE: ford focus overheating

Water pump. No question in my mind, water pump.

Posted on Oct 19, 2008

  • 1 Answer

SOURCE: ford focus overheating

my 2001 ford focus is trying to heat overheat but without the air condition then it go's down quick but I notice that my car kind of hisatates when I had my air on then the air condition feels warm. Then the air gets cold but you can feel when its going to get warm please help I always have problems with garages that try to take advantage of people that do not know about cars.

Posted on Oct 30, 2008

  • 532 Answers

SOURCE: Where is the heater core hose in my 2000 ford expedition?

check closer to just underneath the firewall--it could be a smaller problem than a heater core--Ford 4.6--5.4 engines have a tube just underneath the intake manifold that the rubber hose goes bad and it will leak towards the back of the engine.Lets hope so-what i hear its very expensive to change a heater core in an Expedition.

Posted on May 01, 2009

MNfisherman
  • 11896 Answers

SOURCE: CANT FIND COOLANT TEMP SENSOR 2001 FOCUS 2.0 DOHC

Right on thermostat housing

Posted on Aug 19, 2009

  • 1 Answer

SOURCE: ba falcon heater

Just had the same thing happen to my BA. No hot air. I'm a bit of a handyman so I had a go myself. 8 Hours is a reasonable estimate. You have to remove the steering column and entire dashboard to get the bugger out. Not a job I would attempt again.

Posted on May 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wher is the coolant sensor fpr a 2010 focus


Clear the code and drive the vehicle. If the code comes back, then you know it's real condition and not a one time event.
Changing the temperature sensor isn't going to remedy the situation. Most likely the thermostat will need to be replaced.

Apr 26, 2014 | 2010 Ford Focus 1.6

1 Answer

How to replace a thermostat


2.0L Engine
SOHC ENGINE
(see Figure 17)
  1. Disconnect the negative battery cable.
  2. Remove the air cleaner outlet tube.

CAUTION Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Drain the cooling system until the level is below the thermostat.
  2. Unplug the coolant temperature sender and coolant temperature sensor electrical connections.
  3. Disconnect the upper radiator hose and heater coolant hose from the thermostat housing.
  4. Unfasten the thermostat housing bolts.
  5. Remove the thermostat housing and the thermostat.
  6. Clean the gasket surfaces thoroughly until all traces of the old gasket residue are removed.

Make sure the tabs on the thermostat engage properly into the slots in the housing.


zjlimited_290.jpg

Fig. 17: Remove the thermostat housing mounting bolts-2.0L SOHC engine

To install:

  1. Install the thermostat in the housing making sure the tabs engage.
  2. Install any new gasket required.
  3. Install the thermostat, housing and bolts. Tighten the bolts to 8-12 ft lbs. (10-16 Nm).
  4. Connect the upper radiator hose and heater coolant hose to the thermostat housing.
  5. Attach the coolant temperature sender and coolant temperature sensor electrical connections.
  6. Fill the cooling system.
  7. Install the air cleaner outlet tube.
  8. Connect the negative battery cable.
  9. Start the car and check for leaks.

DOHC ENGINE
(see Figures 18 and 19)
  1. Disconnect the negative battery cable.
CAUTION Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Drain the cooling system until the level is below the thermostat.
  2. Unplug the Camshaft Position (CMP) sensor electrical connection.
  3. Unfasten the water hose connection retaining bolts and move the connection aside.
  4. Remove the thermostat and seal from the housing.
zjlimited_291.jpg

Fig. 18: Location of the water hose connection mounting bolts-2.0L DOHC engine

zjlimited_292.jpg

Fig. 19: Remove the thermostat and seal. Inspect the seal for damage and replace as necessary-2.0L DOHC engine



To install:

  1. Inspect the seal and replace it if damaged.
  2. Install the thermostat and seal in the housing.
  3. Install the water hose connection and bolts. Tighten the bolts to 71-97 inch lbs. (8-11 Nm).
  4. Attach the Camshaft Position (CMP) sensor electrical connection.
  5. Fill the cooling system.
  6. Start the car and check for leaks.

Hope helps (remember to rate this answer).

Dec 21, 2010 | 1999 Ford Escort

1 Answer

2003 Focus Transaxle Coolant light comes on. Just had to have alternator replaced and now this light keeps coming on. Car jerks when the light comes on and tonight when the light came on the car stalled.


I had and identical problem on my 2002 Focus I also just had the alternator replaced I found my positive lead from the Battery to the starter bad it was melted by the terminal end I raplaced the wire loom that it was in (Ford part WC-95725,YS4Z-14301-LB) and so far that has fixed the problem (only been a week) I hope this helps

Jul 13, 2010 | 2003 Ford Focus

1 Answer

My 2003 ford focus ZTS dohc 16v leaks water (not coolant)


There are only 2 ways water can appear that I know of.
(1) Naturally occurring from combustion while you warm up the engine. It lays in the exhaust until it evaporates with heat or makes its way out little bleed holes in the mufflers.
(2) Air conditioner condensation off the evaporator which is SUPPOSED to drop thru a drain hose to the street. The hose can get plugged and it could leak out higher up maybe.
Your air conditioner works even in cooler temps to dehumidify the windshield(in DEFROST or MIX modes). This resulting water is supposed to drain thru that hose off your heater plenum.
don-ohio

Mar 05, 2017 | 2003 Ford Focus

2 Answers

2001 ford focus - plastic coolant tube cracked


it's called the degas bottle becuase it is pressurized and flows coolant through it all the time so it can purge air.

Jan 15, 2010 | 2001 Ford Focus

1 Answer

How to change a thermastat 1994 ford escort with a 1.9 engine


1.9L Engine

CAUTION Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the air intake tube, crankcase breather and PCV hose.
  4. Remove the ignition coil pack and bracket.
  5. Remove the upper radiator hose.
  6. Remove the ignition coil pack bracket.
  7. Unfasten the heater hose inlet tube bracket bolt and remove the heater hose inlet tube from the thermostat housing.
  8. Remove the three thermostat housing attaching bolts, then remove the thermostat housing and gasket.
b2d5ac4.jpg

Fig: Remove the ignition coil pack


b5ad3b2.jpg

Fig. : Detach the air intake tube, crankcase breather and PCV hose


3a3c4dd.jpg
Fig. : Disconnect the upper radiator hose from the radiator


63b3b74.jpg
Fig. : Unfasten the ignition coil pack bracket upper bolts...

076a94a.jpg

Fig. : ...and the lower bracket bolt, then remove the bracket

f656bf8.jpg

Fig. : Unfasten the heater hose inlet tube bracket bolt (arrow)

314321c.jpg

Fig: Unfasten the heater hose inlet tube-to-thermostat housing clamp


3204281.jpg
Fig.: Disconnect the hose inlet tube from the thermostat housing

5dc1ba9.jpg

Fig. : Unfasten the three thermostat housing bolts


2fb60e5.jpg

Fig. Separate the thermostat housing from the engine block


6f1527f.jpg

Fig. : Remove the thermostat from the housing


e33ea6d.jpg

Fig. : Use a scraper to clean old gasket material from the engine block's thermostat housing mating surface ...


db9a50c.jpg

Fig. : ... as well as the thermostat housing

continue...





Oct 29, 2009 | 1994 Ford Escort

1 Answer

Water leak ford focus


if that pipe is neceseria can not eliminate

Aug 11, 2009 | 2002 Ford SVT Focus

1 Answer

I have a 2000 ford focus DOHC when you stop it


I think this is all due to your vacuum leak.
Look for a hose not connected to the throttle body or the intake manifold. Use a piece of hose to find the source of the leak. Hold one end near ear and probe around the engine carefully.

May 09, 2009 | 2000 Ford Focus

2 Answers

CAR WONT STAY RUNNING


disconnect the battery cable for about an hour to restart the engine computer. It will then need to relearn your car's operating paramters again. Once the strategy is relearned, it should be ok.

Mar 03, 2009 | 2000 Ford Focus

1 Answer

2001 ford focus dohc


Easiest way to find the PCV on a 2000 ZX3 (ZTEC engine)is to stand directly in front of the engine and look at the right side of the oil filler cap. From there, approx 10 inches directly below the the right side of the cap, you will see a black rubber hose/tube (3/4 inches)inserted into a rubber grommet--the PCV valve!! If you were to follow the hose/tube back through the emission components, you would find it connects to the lower rear of the throttle body.

Oct 05, 2008 | 2001 Ford Focus

Not finding what you are looking for?
2001 Ford Focus Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...