Question about 2006 Hummer H3

Open Question

2006 hummer turn signal bulb replacement - 2006 Hummer H3

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 2006 hummer h3 replace burnt out left trun signal

if it's the rear light, open the back door all the way and look where it hinges. There are two phillps screws in there that you remove and then go out side the door and gently pull streight back on the light assy to remove it

Posted on Dec 04, 2010

  • 1 Answer

SOURCE: 2006 H3 Hummer rear passenger turn signal non-op.

I have the same problem.help please

Posted on Sep 14, 2011

  • 344 Answers

SOURCE: 2008 Hummer H3 passenger side tail lamp out.

There could be loose wire at the bulb socket ,A break in a wire, Or a bad ground, Or a short, Best way to have it solve is to take it into a auto eletric shop to be check out,

Posted on Nov 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

06 H3 Hummer right turn signal goes on by itself can't turn off


Turn Signal Lamps
The FRT/TRN/HAZ/CRTSY/MIRR and REAR/TRN/HAZ fuses in the underhood fuse block supplies battery positive voltage to the body control module (BCM). When the turn signal switch is placed in either the left or right position, a signal is sent to the BCM to illuminate the desired turn signal lamps. The BCM has an internal flasher that sends an ON-OFF voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, a separate ground signal is sent to the BCM to activate and flash all turn signal lamps including both IPC turn indicators. The front and rear turn signals are grounded at G105, G350 and G340. The sound for the turn signal indicators is produced by the IPC.

DTC B0525 Left Turn Signal Circuit
• DTC B0527 Right Turn Signal Circuit Low
• DTC B0528 Right Turn Signal Circuit High
• DTC B0529 Right Turn Signal Circuit Open
DTC B0530 Right Turn Signal Circuit
• DTC B0532 Left Turn Signal Circuit Low
• DTC B0533 Left Turn Signal Circuit High
• DTC B0534 Left Turn Signal Circuit Open
Could be a switch problem , short to ground on the signal circuit to the BCM , BCM seeing a input that shouldn't be there etc....
I would have it checked for DTC'S diagnostic trouble codes .

Jun 10, 2017 | 2006 Hummer H3

1 Answer

I have a 2006 h3 hummer with no brake lights or turn signals. I have replaced the turn signal switch. Can anyone help me with this


Check switch on the brake pedal,check globes in the rear of car have power going to them,you will need a test light to test them.

Mar 29, 2017 | 2006 Hummer H3

1 Answer

2006 Hummer H2 left rear bumper turn signal / brake light does not work. Bulb is good, same light works as tail light, but doesn not work as brake light or turn signal. Problem is also present in trailer...


if someone added an aftermarket item to your lights, they may not work correctly, have it looked at by a professional who does that type of thing for a living.

Oct 15, 2013 | 2006 Hummer H2

1 Answer

2008 Hummer H3 passenger side tail lamp out.


There could be loose wire at the bulb socket ,A break in a wire, Or a bad ground, Or a short, Best way to have it solve is to take it into a auto eletric shop to be check out,

Nov 28, 2012 | 2008 Hummer H3

1 Answer

Install front turn signal on h3


You need to remove the front wheel hose panel to gain access to the turn signal bulbs.Hope this helps.Good luck.

Feb 25, 2012 | 2006 Hummer H3

2 Answers

2006 H3 Hummer rear passenger turn signal non-op. Replaced bulb -same also checked fuse - same. need another avenue to check.


Did you check hazard operation, what is the turn signal on dash blink rate(faster than other side)? Make sure socket is clean of corrosion and terminal pins not burnt.

May 11, 2011 | 2006 Hummer H3

1 Answer

Change out a taillight


You want to change the tail light bulb?

The process for replacing tail light bulbs is the same in all models. If you have a burnt-out tail light bulb, you may need to replace the brake light, the reverse light or the turn signal. The procedure to replace each of the bulbs is the same.



    Instructions

    1. Open the Hummer's rear swing gate. This will expose the edge of the vehicle's tail light assembly. You'll see two small Phillips head screws that hold the tail light assembly in place. Put on your gloves.

    2. Remove the two screws from the tail light assembly. Pull the tail light out and inspect the back for two bulbs. The top bulb is the brake light and turn signal. The bottom bulb is the reverse bulb. Determine which bulb you need to replace.

    3Rotate the bulb's socket counterclockwise to disconnect it. Unplug the bulb from its socket.

    4Push the replacement bulb into its socket firmly. Insert the socket back into the tail light. Turn it clockwise to secure it in place.

    5Place the tail light into its cradle. Hold it with one hand and replace the Phillips head screws with the other.

Dec 03, 2010 | 2008 Hummer H3

1 Answer

2006 hummer h3 replace burnt out left trun signal bulb


if it's the rear light, open the back door all the way and look where it hinges. There are two phillps screws in there that you remove and then go out side the door and gently pull streight back on the light assy to remove it

Nov 20, 2010 | 2006 Hummer H3

3 Answers

My h3 hummer has some kind of problem with the signal rear lights and the break rear light i check the fuse and that not the problem whatg to do now???


my h3 hummer runing light on trailer do not work i have no power at the plug the turn & stop lights work

Apr 23, 2010 | 2006 Hummer H3

1 Answer

Cant figure out how to replace front blinker bulb


You need to remove the front grill to get at the front turn signals (and bulbs). A lot of work for what should be much easier.

hope it works

Jan 09, 2010 | 2006 Hummer H3

Not finding what you are looking for?
2006 Hummer H3 Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hummer Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Hummer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...