Question about 2009 Ford Escape Hybrid

Open Question

Code p1a10 starting 30 sencon

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine start but off in 30 seconds


Have the fault codes read. Replace faulty items. Use only genuine items as non-genuine replacement are not always compatible with the OEM fitted CPU units .check for cam or crank shaft position sensor or idler sensor problems

Jun 24, 2013 | Cars & Trucks

1 Answer

Car wont go 30 mph


could be catalytic con. plug up.

Jun 03, 2013 | Hyundai Cars & Trucks

1 Answer

2003 yukon starts with the remote, runs about 30 seconds then shuts off, then restarts for 30 seconds and shuts off, over and over


remote start might need reprogrammed check for codes in system security code may have set

Jul 02, 2012 | 2003 GMC Yukon

1 Answer

My car shuts off while driving. I'm not low on gas, or oil. It was not over heating. If i let the car sit for about 30 minutes, it will start back up again and drive for about 30 minutes before it


The engine in this car is electronically controlled and a problem like this would leave a fault code in the memory of the computer control module, to retrieve this code or codes you need the system scanned with a special tool, this is called an "OBD 2" fault code test.

May 01, 2012 | Hyundai Motor 1998 Accent

1 Answer

Just replaced steering coluim in a 2002 chevy cavalier and the car won't start how do i get the theftlock code


Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself.

Nov 22, 2009 | 2002 Chevrolet Cavalier Coupe

2 Answers

1990 dodge caravan starts then dies after 30 seconds.


cycle key, on,off,on,off,on & leave it on (not start) & count flashes from check engine light to see if getting any trouble codes. example: 2 flashes, pause, 2 more, is code 22. 3 flashes,pause & 3 more, is code 33, etc.. let us know what you get, if any. P.S. Code 55 - 5 flashes,pause 5 more, is end of message.

Jun 04, 2009 | 1990 Dodge Caravan

1 Answer

2000 VW Beetle dies occasionally and won't start for a while


run a scan tool on it and make sure there are no codes, if there is codes address those problems first, if no codes.. next time it won't start check for fuel preasure. it is probably a fuel pump getting ready to go out or they may be a large amount of something other than gas clogging the pick-up sock at bottom of fuel pump.

Mar 07, 2009 | 2001 Volkswagen Beetle

Not finding what you are looking for?
2009 Ford Escape Hybrid Logo

Related Topics:

200 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...