Question about 2006 Ford F 350 Super Duty

Open Question

Code b1352

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 lincoln town car light control module wiring diagrams


You don't need a wiring diagram ,what you need is a scan tool that will pull codes from the LCM , an LCM Parameter Identification (PID) Index ! Checking codes first !
LCM Diagnostic Trouble Code (DTC) Index DTC Description DTC Caused By Action B1312 Lamp Headlamp Input-Short to B+ LCM REFER to Section 417-01 . B1334 Decklid Ajar-Short to Gnd LCM REFER to Section 501-14B . B1340 ESC Tone Input Request Short to Ground LCM REFER to Section 501-14B . B1342 ECU-Defective LCM REPLACE the LCM. REFER to Section 419-10 . TEST the system for normal operation. B1352 Ignition Key-In-Ckt Failure LCM GO to Pinpoint Test C . B1359 Ignition Run/Acc Circuit Failure LCM REFER to Section 211-05 . B1462 Seat Belt SW_Ckt Failure LCM GO to Pinpoint Test B . B1485 Brake Pedal Input Circuit Short to Batt. LCM REFER to Section 417-01 . B1555 Ignition Run/Start Circuit Failure LCM REFER to Section 211-05 . B1569 High-Beam-Short to B+ LCM REFER to Section 417-01 . B1577 Park Lamp Input-Short to B+ LCM REFER to Section 417-01 . B1581 Panel Dim Increase Input Circuit Short to B+ LCM REFER to Section 413-00 . B1585 Dim Panel Decrease Input Circuit Short to B+ LCM REFER to Section 413-00 . B1676 Battery Voltage Out of Range LCM REFER to Section 414-00 . B1687 Dome Lamp Input Short to B+ LCM GO to Pinpoint Test D . B1689 Autolamp Delay Input Circuit Failure LCM REFER to Section 417-01 . B1691 Autolamp Delay Input Circuit Short to B+ LCM REFER to Section 417-01 . B1695 Autolamp ON/OFF Short to B+ LCM REFER to Section 417-01 . B1873 Turn Signal/Hazard Power Feed Short to Ground LCM REFER to Section 417-01 .

Aug 12, 2016 | 2000 Lincoln Town Car

1 Answer

Where is chime module located on 2005 ford taurus


There is no chime module ,there is a speaker inside the instrument cluster.
Door Ajar Chime
The door ajar chime feature is controlled by the smart junction box (SJB). The driver and passenger door ajar switches, and the liftgate are hardwired to the SJB. If any door or liftgate is sensed as being open, and the ignition switch is in RUN/START position, the SJB will process the input and sends a chime request to the instrument cluster over the controller area network (CAN).
Safety Belt Warning Chime
The safety belt chime feature is controlled by the restraints control module (RCM). The driver safety belt switch is hardwired to the RCM. The RCM communicates with the instrument cluster over a hardwire connection. If at any time during the first 6 seconds after the ignition switch is placed in RUN the driver safety belt is sensed as being unfastened, the RCM will process the input, and in turn, sends a chime request to the instrument cluster.
Have the vehicle checked for DTC'S - diagnostic trouble codes ,not OBD 2 codes , the check engine light has nothing to do with this .
Instrument Cluster Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 Instrument Cluster is Defective Instrument Cluster INSTALL a new instrument cluster. REFER to Section 413-01 . B1352 Ignition Key-In Circuit Failure Instrument Cluster Go To Pinpoint Test B . B2477 Module Configuration Failure Instrument Cluster REFER to Section 413-01 .
For a complete list of instrument cluster DTCs, refer to Section 419-10 .


Smart Junction Box (SJB) Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 SJB is Defective SJB INSTALL a new SJB. REFER to Section 419-10 . B1352 Ignition Key-In Circuit Failure SJB Go To Pinpoint Test B . B1577 Lamp Park Input Circuit Short to Battery SJB Go To Pinpoint Test E . C1167 Park Brake Actuator Assembly Switch Released Circuit Short to Ground SJB Go To Pinpoint Test F . Your best bet is to have a qualified repair shop diagnose this problem ,what ever it is .
Have the vehicle

May 28, 2016 | Ford Cars & Trucks

1 Answer

The truck release does not respond to the key fob or the door release. Driver door lock does not respond to the fob or the number pad on the door.


The best place to start is take it an have it checked for DTC'S -diagnostic trouble codes ! Not with a code reader ,as these just read OBD2 codes .Not Body control module codes >
DDM Diagnostic Trouble Code (DTC) Index
DDM Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1322 Driver Door Ajar Circuit Short to Ground DDM Go To Pinpoint Test N . B1352 Ignition Key in Circuit Failure DDM Go To Pinpoint Test H . B1396 Power Door Lock Circuit Short to Battery DDM Go To Pinpoint Test A . B1397 Power Door Unlock Circuit Short to Battery DDM Go To Pinpoint Test A . B1526 Keyless Entry Circuit Short to Ground DDM Go To Pinpoint Test E . B1553 Decklid Release Circuit Short to Battery DDM Go To Pinpoint Test B . B1751 Park/Neutral Switch Circuit Short to Battery DDM Go To Pinpoint Test K . B2425 Remote Keyless Entry Out of Synchronization DDM Go To Pinpoint Test L . LCM Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1300 Power Door Lock Circuit Failure LCM Go To Pinpoint Test M . B1310 Power Door Unlock Circuit Failure LCM Go To Pinpoint Test M . B1319 Driver Door Ajar Circuit Failure LCM Go To Pinpoint Test N . B1322 Driver Door Ajar Circuit Short to Ground LCM Go To Pinpoint Test N . B1396 Power Door Lock Circuit Short to Battery LCM Go To Pinpoint Test M . B1397 Power Door Unlock Circuit Short to Battery LCM Go To Pinpoint Test M . B1677 Alarm Panic Input Circuit Failure LCM Go To Pinpoint Test O . B1679 Alarm Panic Input Circuit Short to Battery LCM Go To Pinpoint Test O . Visual Inspection Chart Mechanical Electrical
  • Binding latches
  • Battery junction box (BJB) fuses:
    • circuit breaker 7 (20A)
  • Central junction box (CJB)
    • 4 (10A)
    • 6 (15A)
    • 8 (25A)
    • 13 (5A)
  • Keyless entry keypad switch
  • Power door lock actuator
  • Luggage compartment release switch
  • Luggage compartment release solenoid
  • Connectors or connections
  • Wiring harness

Dec 30, 2015 | 2001 Ford Crown Victoria

3 Answers

No give fire heve new coil and fuel pump


This code is for ABS and will have nothing to do with a no start condition. What size motor is in the vehicle? I need to know in order to offer assistance

Jul 14, 2015 | 2002 Mercury Cougar

1 Answer

Ranger won't crank.


accessory relay delay Coil Circuit Failure.There is a delay relay that is under the dash in the fuse panel.

Dec 03, 2013 | 1998 Ford Ranger SuperCab

1 Answer

B1352


Here's a link to your code.

Mar 11, 2013 | 1997 Lincoln Town Car

1 Answer

B1352


The following are the general instructions on the start of diagnosing any electronically controlled engine or transmission problem.

The engine and the automatic transmission (transmission control is only for automatics, engine is still computer controlled no matter the transmission type) in this vehicle are computer controlled and in most cases when a fault occurs a fault code is stored in the memory of the computer control module. There are exception to this, such as the Mass Airflow Meter and fuel pressure problems. What must be done is to have all the basic testing done such as a scan of the system for fault codes as well as a check with a live data scanner tool for engine functions that are not within range of normal, a trained technician is required to know what is correct and what isn't, then based on careful diagnostics done from a factory repair manual the correct part is replaced or the wiring repaired or the computer replaced (known as the PCM or ECM,ECU), which is very rarely the problem. Other basic checks must be done as well such as mechanical problems with the engine as well as engine state of tune and mileage on the engine. The transmission can have mechanical issues as well such as no gear engagement at all or a failed pump or other pressure related problems. Also engine mechanical problems can and do cause many drive-ability related problem such as rough idle and other symptoms.

Nov 01, 2012 | 2001 Ford Escape

1 Answer

Ford Explorer wipers, power windows, doom lights won't work


Are u assuming the GEM module is at fault ? Did you or your local auto electrician check for DTC'S - diagnostic trouble codes?
GEM/CTM Wiggle Test Diagnostic Trouble Code (DTC) Index DTC Description DTC Caused By B1317 Battery Voltage HIGH GEM/CTM B1318 Battery Voltage Low GEM/CTM B1322 Driver Door Ajar Circuit Short to Ground GEM/CTM B1330 Passenger Door Ajar Short to Ground GEM/CTM B1352 Ignition Key-In Circuit Failure GEM/CTM B1410 Driver Power Window Motor Circuit Failure GEM B1438 Wiper Mode Select Switch Circuit Failure GEM/CTM B1441 Wiper Mode Select Switch Short to Ground GEM/CTM B1446 Wiper Park Sense Circuit Failure GEM/CTM B1450 Wiper/Wash Interval Delay Switch Input Circuit Failure GEM/CTM B1453 Wiper/Wash Interval Delay Switch Input Short to Ground GEM/CTM B1462 Seat Belt Switch Circuit Failure GEM/CTM B1577 Park Lamp Input Circuit Short to Battery GEM/CTM B1610 Illuminated Entry Input (From RAP Module) Circuit Short to Ground GEM/CTM
Did you an your auto electrican check power an grounds for the GEM ? Voltage drop testing ? . Did you check power an ground circuits for the affected systems . Working when they want sounds more like a loose connection somewhere .
ECM Inputs and Outputs Diagnosis
Symptom Chart
Symptom Chart Condition Possible Sources Action
  • The Wipers Are Inoperative
  • CJB Fuse 16 (30A).
  • Circuitry.
  • GEM/CTM.
  • Multi-function switch (13K359).
  • Wiper run/park relay.
  • Wiper HI/LO relay.
  • Wiper motor.
  • DTC B1431.
  • DTC B1432.
  • DTC B1438.
  • DTC B1450.
  • DTC B1840.
  • GO to Pinpoint Test A .

Plus looking at GEM scan data on a factory scan tool .Too many people miss diagnose these system's because they don't have a clue .

Jul 03, 2017 | 1999 Ford Explorer

2 Answers

Cyliner 1 misfire, codespo301, po316, po301b, b1352


A misfire can be cause by several factors. here are a list of things to check check spark plug on that cylinder and check coil and wiring for coil. check cylinder compression on all cylinders if one cylinder is less than 10 psi different from the others that can cause a miss, last but not least check injector pulse using a noid light for injector pulse if pulse is good then injector is bad replace and that should solve your problem. Good luck and contact if you need more help. Thanks for using FIX YA

May 12, 2009 | 2006 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...