Question about Cars & Trucks

Open Question

Uplander sliding door

What should I use to clean the sensors and contacts on the side rear power doors on my 08 chevy uplander

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
micromaster
  • 3614 Answers

SOURCE: My 1999 pontiac montana rear sliding power door will not work

hi there,

this can be stuck contacts on the door. better to check the sliding contact point for any dirt debris on the slide or it may need some lubricant for easily sliding.

Posted on Apr 18, 2009

Ad
michigan man
  • 3533 Answers

SOURCE: how do you reset power sliding door on 2000 chevy venture

there should be information in your owner manual telling you how to do it if you have miss place your owner manual try this website to see if you can down load one for your car its www.edmunds.com and i hope i was able to help you Michigan Man

Posted on May 12, 2009

  • 82 Answers

SOURCE: 2006 Chevy Uplander. The power sliding doors won't shut

2 possible solutions. First clean the door pin contacts(multiple spring loaded pins on door side and matching plate on body) with a scotch pad until shiny gold color again. Second the rear edge of the door should be 1mm inside the body opening when closed. If those are correct it is going to take a software download from a dealer to the door control module to fix this. Otherwise you will have to pull the psd fuse and breaker from the right side dash fuse box.

Posted on Jun 23, 2009

iambanshee74
  • 3489 Answers

SOURCE: 08 avalanche pass side power door lock not working

if you have any knowledge of automotivce electrical, (and that you need to use a "circuit tester" and not a test light) test for power when someone presses the button. it wouldnt be uncommon for most vehicles for the lock actuator/solenoid/duty actuator to wear out, get weak and fail. this is most probable. given that this is an 08, have you checked withe dealer to see if its still under warranty. if we are only talking a few miles and they wont do anything, look in your owners handbook and get the 1 800 number and get GM's customer service involved. cheers.

Posted on Dec 02, 2009

  • 3 Answers

SOURCE: chevy uplander sliding door sensor will not stop

Remove the PSD fuse, its on the inside fuse panel

Posted on Jan 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the rear heater motor located on 2008 uplander


If the van has E59 on the RPO sticker you have to remove the left rear lower trim panel to access the motor. If it does not have E59 just remove the left rear compartment lid and compartment to access the motor. RPO E59 is a power left sliding door.

Sep 24, 2014 | 2008 Chevrolet Uplander

2 Answers

Door chime on 2007 chevy uplander will not stop even when the door is closed properly. Is there anyway to disable it


unfortunately the fuse that runs the chime also runs other items on that circuit so pulling the fuse isn't an option, basically what you need to do is check each door switch , one is shorted, and is in the open position,, they are located at the side rails of each door, remove the deco rubber trim, and you will see that a screw holds them on, they pop right out, with a meter, check each switch for continuity with the switch in the OUT position, when the switch is depressed, you should get no reading, since that closes the circuit, you can either replace the bad switch, ( sometimes they just get stuck,m so move them around and spray some electrical contact cleaner on each one) BY the way,, on this model of vehicle, there have been a number of issues with the sliding door latch ,, here are some of the issues ,, http://www.lemonlawclaims.com/Chevrolet_uplander_sliding_door.htm

Sep 10, 2011 | 2007 Chevrolet Uplander LT Minivan

1 Answer

Have to replace a chevy uplander 2008 left rear (passenger side) tail light assembly -- how to?


open rear hatch and will see the access screws un screw careful not to drop and pull away like opening a door and assembly is free from van

Jun 10, 2010 | 2008 Chevrolet Uplander

2 Answers

Door chime on 2007 chevy uplander will not stop even when the door is closed properly. Is there anyway to disable it without disabling radio


Had this problem for some time. I have had the dealer replace motor etc. Problem still returns. Noticed that the foam seal around the right side door has started flatening out over time and was beginning to spill into the lipped plate that the door sensor buttons possibly could be prevented from making proper contact. Trimmed approx. 3/8 of an inch off the foam in the area of the plate, and the problem seems to have gone away. Hope this helps.

Apr 25, 2010 | 2007 Chevrolet Uplander LT Minivan

1 Answer

I have an 05 uplander and i hear a chiming noise while driving and after i park it and take the keys out i dont know what it is,does anyone know?


there are little copper looking contacts on the rear sliding doors check to make sure they are clean you can use a little sand paper to clean them. the noise is because the car thinks one of the doors are open and it might not show on the dash.

Mar 23, 2010 | 1998 Ford Explorer

3 Answers

Power sliding door will not stay closed. once activated the door goes to the closed position then opens back up. how can this be corrected.


Option 1: where the metal contacts on the door meet the metal contacts on the panel, take a high-grit sandpaper and sand those contacts.
Option 2: ensure that there isn't any debris in the tracks that the doors slide on, both on top and the bottom. The vehicle is equipped with a safety sensor that won't allow it to close if something is in its path.
Also check the weather seals around the door for damage.

Jan 02, 2010 | 2006 Chevrolet Uplander

2 Answers

Chevy uplander sliding door sensor will not stop


Remove the PSD fuse, its on the inside fuse panel

Sep 17, 2009 | 2002 Chevrolet Uplander

5 Answers

2006 Chevy Uplander. The power sliding doors won't shut


2 possible solutions. First clean the door pin contacts(multiple spring loaded pins on door side and matching plate on body) with a scotch pad until shiny gold color again. Second the rear edge of the door should be 1mm inside the body opening when closed. If those are correct it is going to take a software download from a dealer to the door control module to fix this. Otherwise you will have to pull the psd fuse and breaker from the right side dash fuse box.

Jun 23, 2009 | 2005 Chevrolet Uplander

1 Answer

Key fob needs programming


call 509-456-7890 they maybe able to help!!!

Jun 22, 2009 | 2005 Chevrolet Uplander

1 Answer

Passenger sliding door


clean the contacts on the door jam and the door itself

Robert

Feb 01, 2009 | 2006 Chevrolet Uplander

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...