Question about 2006 Ford F-250 Super Duty

Open Question

Dtc code U2013 - 2006 Ford F-250 Super Duty

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I put another abs moule on my 2002 Cadillac and lights are still on how do I clear the lights


Have the codes checked ! Do you know what codes are ,What the light is for ? The light is to warn the driver that there is a problem in the ABS system . Have the codes checked before replacing parts ,the code will point you in the direction to go .This system can set numerous DTC'S
DTC C1211 DTC C1214 DTC C1217 DTC C1218 DTC C1221-C1235 DTC C1236 DTC C1237 DTC C1238 DTC C1242 or C1243 DTC C1248 DTC C1251 (w/F45) DTC C1254 DTC C1255 or C1256 DTC C1261-C1274 DTC C1276, P1644, or P1689 DTC C1277 or P1571 DTC C1278 DTC C1281, C1283, or C1286 DTC C1282 DTC C1284 or C1285 DTC C1287 or C1288 DTC C1291 or C1293 DTC C1294 DTC C1295 Maybe your best bet would be to take your vehicle to a ASE certified repair shop or the dealer

Jan 10, 2016 | 2002 Cadillac Deville

3 Answers

Get codes for my 1997 blazor


Code Reader or Professional Scan Tool
to retrieve codes & other data

Nov 20, 2014 | 1997 Chevrolet Blazer

1 Answer

Where is the obd2 connector location on holden ra rodeo v6


isuzimpuls.gif
Connect white (test lead) and black (ground lead) wires that are branched from harness approximately eight inches from ECM. After leads are grounded, the "Check Engine" light will flash the diagnostic trouble codes. The DTC's are indicated by the flashing CEL.
FLASH, FLASH, pause, FLASH, FLASH, FLASH = Code 23.
If only one diagnostic trouble code is stored, the DTC will repeat continuously until test leads are disconnected. If more than one diagnostic trouble code is stored, each DTC will repeat three times, starting with the lowest, then proceed to the next DTC. After all DTC's have been displayed, the pattern will repeat.I-MARK 84-85
Connect male and female test leads taped into wire harness near ECM. After leads are connected, the "Check Engine" lamp will flash the trouble codes. The DTC's are indicated by the flashing CEL.
FLASH, FLASH, pause, FLASH, FLASH, FLASH = Code 23.
If only one diagnostic trouble code is stored, the DTC will repeat continuously until test leads are disconnected. If more than one diagnostic trouble code is stored, each DTC will repeat three times, starting with the lowest, then proceed to the next DTC. After all DTC's have been displayed, the pattern will repeat.
86-87 Impulse located near the ECM connector, is used to actuate the Engine Control Module (ECM) trouble code memory within the module. Two terminals (A and C) of this connector are used to activate the diagnostic trouble code system in the ECM. With the ignition switch turned On, engine Off, connect a jumper wire between terminals A and C. The "Check Engine" lamp will begin by flashing a DTC 12. DTC 12 = flash, pause, flash, flash. There will be a longer pause and a code 12 will repeat two more times. This code indicates the self-diagnostic system is operating. The cycle will then repeat until the engine is started or the ignition is switched Off. In most cases, DTC's will be checked with the engine running since no DTC's other than DTC 12 or 51 will be present without the engine running. Remove jumper wire from ALDL connector before starting engine. Reconnect jumper wire after engine is running.

Throttle Body Fuel Injection

The ECM test connection is located under the center console.
A built-in, self diagnostic system will identify problems in the throttle body fuel injection system. When a problem is detected, the diagnostic system will illuminate the "Check Engine" light.
When the engine is started, the Check Engine light should turn off.. If the light remains lit, the self diagnostic has detected a problem. To determine where the problem exists, ground the "Test" terminal of the connector with the ignition On, engine Off and watch the check engine light. Each DTC will flash three times (lowest to highest).

Aug 21, 2014 | Holden Rodeo Cars & Trucks

1 Answer

What's the actual meaning of DTC codes 41, and 58, for this vehicle?


the meaning of codes 41 and 58 is:

DTC - 41 Ignition control error

DTC - 41 MEM- CAL error
DTC - 41 Cam sensor sinal error

DTC - 58 Trans fluid temp sensor circuit error (low voltage)
DTC - 58 VATS System error

I hope this is helpful

Feb 18, 2013 | 1992 Buick LeSabre

1 Answer

How do you reset the security light on a 2005 chevy cobalt?


There is no reset , if security light is lit there is a problem with the anti-theft system .Should have it checked for DTC'S - diagnostic trouble codes . Could have 8 different B - codes
DTC B0685 DTC B2955 DTC B2960 DTC B3031 DTC B3033 DTC P1626 DTC P1630 DTC P1631
You would need a professional type scan tool to read these type codes , not an OBD 2 code reader .

Apr 14, 2012 | Cars & Trucks

1 Answer

Ford diagnostic code u2013


according to ford specific U codes, it is to warn you about "compass module is not responding".

Nov 23, 2011 | 2008 Ford F 250 Super Duty 4WD

1 Answer

Code po120 mazda protege 1.5 L..code po110...code po115.....code po195



P0110 DTC - IAT Circuit Malfunction

P0115 DTC - Engine Coolant Temperature Circuit Malfunction

P0120 DTC - TPS A Circuit Malfunction

P0195 DTC - Engine Oil Temperature Sensor Malfunction

Hope this helps to identifiy.

Oct 04, 2011 | Cars & Trucks

1 Answer

2006 lincoln town car


Did the dealer clear the codes last time you were in. they have to be cleared

Jul 28, 2008 | 2006 Lincoln Town Car

Not finding what you are looking for?
2006 Ford F-250 Super Duty Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...