Question about Jeep Grand Cherokee

1 Answer

1991 jeep grand cherokee steering column removal

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

The whole thing, ? end to end?>
or just need to drop it a tad?. why not post the job. and why.
context matters, (need ign. switch out?>, what?)
why not read the FSM ?
chapter 19, id bet this answers all questions, same answer all cars made. read the FSM first then ask questions no clear there.


http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

posted 100 times, or more here.
searches do work.

Posted on Dec 22, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
polarcycle
  • 1392 Answers

SOURCE: 2005 Jeep Grand Cherokee rear seat removal

For the seat bottom, you just need to pull it up. The seat backs would have to be unbolted.

Posted on Mar 06, 2009

  • 1 Answer

SOURCE: window motor replace 2001 jeep grand cherokee

You need to remove all the skrews from the door. Normaly there is one in the handle of the door, one behind the in door lach handel and one under the bump out for the arm rest on the door. Than you need to take a flat head skrew driver slowly priying the panel off. There are plastic clips on the backside of the panel it is ok if you brake a few.

Posted on May 01, 2009

  • 90 Answers

SOURCE: HOW TO REMOVE HEADLIGHT ASSEMBLY 2006 JEEP GRAND CHEROKEE

remove the 7mm bolt in the centre top of lamp unit then with a big screwdriver just behind headlamp prise outwards quite firmly

Posted on Jul 03, 2009

  • 30 Answers

SOURCE: 99 Jeep grand cherokee steering column makes a clunking

power steering pump might need more oil (whining noise). generally power steer pumps take automatic transmission fluid. there should be a reservoir above the pump only fill this a little bit then start the car and turn left to right and recheck level. fluid should only be low if there is a leak at power steer pump/lines or steering rack,

Posted on Jul 29, 2009

CMV9
  • 594 Answers

SOURCE: How do I remove the ignition lock cylinder from

here are the instruction the first set are the instruction on how to remove the turn signal switch as you will need them to remove the ignition

Removal & Installataion of turn signal switch

  1. Disconnect the negative battery cable.
  2. Remove the steering wheel.
  3. Loosen the anti-theft cover retaining screws on 1976 models and lift the cover from the steering column. It is not necessary to completely remove these screws.
  4. Depress the lockplate and pry the round wire snapring from the steering shaft groove. A lockplate compressor tool is available for compressing the lockplate.
  5. Remove the lockplate, directional signal canceling cam, upper bearing preload spring, and thrust washer from the steering shaft.
  6. Move the directional signal actuating lever to the right turn position and remove the lever.
  7. Depress the hazard warning light switch and remove the button by turning it counterclockwise.
  8. Remove the directional signal wiring harness connector block from its mounting bracket on the right side of the lower column.
  9. On vehicles equipped with an automatic transmission, use a stiff wire, such as a paper clip, to depress the lock tab which retains the shift quadrant light wire in the connector block.
  10. Remove the directional signal switch retaining screws and pull the switch and wiring harness from the steering column.
  11. Guide the wiring harness of the new switch into position and carefully align the switch assembly. make sure that the actuating lever pivot is correctly aligned and seated in the upper housing pivot boss prior to installing the retaining screws.
  12. Install the directional signal lever and actuate the directional signal switch to assure correct operation.
  13. Place the thrust washer, spring, and directional signal canceling cam on the upper end of the steering shaft.
  14. Align the lockplate splines with the steering shaft splines and place the lockplate in position with the directional signal canceling cam shaft protruding through the dogleg opening in the lockplate.
  15. Install the snapring.
  16. Install the anti-theft cover.
  17. Install the steering wheel and connect the negative battery cable.
  18. Check the operation of the turn signal switch.

Removal & Installation of ignition lock switch
  1. Disconnect the battery ground cable.
  2. Remove the turn signal switch as described earlier in this section. You don't have to remove the switch completely, just set it aside.
  3. Insert the key. Position the key as follows.
    • 1976-83: With manual transmission, put it in the ON position; with automatic, put it in OFF/LOCK.
    • 1984-86: Two detent positions, clockwise, beyond OFF/LOCK.
  1. Working through the slot next to the turn signal switch mounting boss, use a thin screwdriver to release the lock cylinder.
  2. To install, insert the key in the new lock cylinder. Hold the sleeve and turn the key clockwise until it stops. Align the cylinder retaining tab with the housing slot and insert the cylinder. Push the cylinder in, rotate to engage, then push in until the retaining tab engages the housing groove.
  3. Complete the procedure in the reverse of removal.

Posted on Aug 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I know if my ignition switch is bad on my 1995 jeep grand cherokee lerado 5.2 liter


The ignition switch does not usually go bad on Grand Cherokees but the ignition key cylinder does and it usually just stop turning, stuck in place. Key cylinder can be removed by taking the steering wheel off to access the little clip that's holding the key cylinder in place, inside the steering column.

Jul 27, 2011 | 1995 Jeep Grand Cherokee

1 Answer

My brake lights are out in my 2004 grand cherokee, already check bulbs, fuses and pedal switch.....seems ok to me


Your turn signalswitch is most likely the culprit. You have to remove the steering wheel to replace it. Just don't turn the wheels to tightly when you remove the steering wheel. or you could damage the clock spring inside the steering column.

Dec 10, 2010 | 2004 Jeep Grand Cherokee

1 Answer

How to install a brake light switch on a Grand Jeep Cherokee


Dont do it... It will take you bout 30 minutes to remove and replace it on the steering column

Dec 04, 2009 | 2001 Jeep Grand Cherokee

1 Answer

Steering column has a 1 inch wobble to it


I'm sure there are bolts holding the steering column. This
can be found under the dashboard. Just tighten it up to
correct the problem.

Nov 11, 2009 | 1991 Jeep Cherokee Limited

1 Answer

How do you remove/replace wiper switch on 1995 jeep grand charokee


Disconnect and Isolate Negative Barrety cable. Remove screw in bottom of steering column shroud cover. ( bottom side of steering column between wiper switch and turn signal switch) Unsnap shroud halves and remove from column. Disconnect wireing harness connector from multi function switch. Remove 2 screws securing switch to mounting housing. Install in reverse order.

Oct 25, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Air bag light keeps coming on my 1999 jeep grand cherokee


Jeeps did have a problem with the clock spring in the steering column. This clock spring is a part that connects the lower harness with the switches on the steering wheel. To replace the clock spring it will have to be done by a qualified tech since the airbag itself has to be removed. Have the car checked for codes first before making any repairs.

Mar 05, 2009 | 1999 Jeep Grand Cherokee

1 Answer

1995 jeep grand cherokee


Steering wheel has to come off and airbag disconnected (by a qualified tech or it can blow open in your face) speacial tool needed for steering column clip removal and install, should I go on?

Dec 29, 2008 | 1995 Jeep Cherokee

1 Answer

Turn Signals Won't Work 2003 Jeep Grand Cherokee


hi roberto
its probably the small copper contacts in the plastic unit that encompasses the steering column this can be purchased and refitted quite easily by removing the steering wheel,removing the securing screws unplugging the electrical loom plug and slipping over the steering column. replace new unit in reverse . probably caused by over-exadurated movement of the signalling lever

Oct 24, 2008 | 2003 Jeep Grand Cherokee

1 Answer

2002 jeep grand cherokee


Basicly you have to take apart the steering column cover and the switch is held in place with screws.
If you have to take the steering wheel off, it is best done by a qualified tech. There is an airbag in the steering wheel that has to be disconnected. THIS AIRBAG CAN GO OFF, PLEASE DO NOT TRY THIS YOURSELF!!!!!!!

Sep 16, 2008 | 2002 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...