Question about 2000 Suzuki Esteem

1 Answer

Front rotor

Remove

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 14,204 Answers

Here's a link on your rotor.

Posted on Nov 17, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove the front rotor


Take the brake caliper bolt and try tightening it against the rotor and then back it off. Turn the rotor, tighten, then back it off and repeat this until the rotor pops loose.

Nov 01, 2012 | Cars & Trucks

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

1 Answer

Can'tremove the rotors on my mitsubishi 2008 Eclipse Spyder GT. What am I missing


Brake Rotor Removal & Installation Front Front brake caliper & rotor removal/installation mitsubishi-09-00-7842.gif

Rear Rear brake caliper & rotor removal/installation mitsubishi-09-00-7843.gif

prev.gif next.gif

Jul 31, 2010 | Mitsubishi Spyder Cars & Trucks

1 Answer

How do you remove front brake rotors


remove tire. remove caliper bolts, hang caliper out of the way. Remove caliper support bracket. cut or pry off rotor securing ring from one wheel stud. wiggle off rotor...rubber mallet may be needed if rust is present.

May 20, 2010 | 2004 Toyota Corolla

2 Answers

How to remove the rotor on a navigator?


front or rear brake rotor? b sure to shut off the air ride system! the switch is located in the rear kick panel! lift and support front remove tires !the caliper has two mounting bolts remove those and hang caliper to the side using a metal coat hanger! now look at the bracket that was connected to the caliper remove those two bolts !the rotor should come off

Mar 16, 2010 | 2001 Lincoln Navigator

1 Answer

How to replace 99 gmc 3/4 tom brake rotors


Removal & Installation
  1. Remove 2/3of the brake fluid from the master cylinder.
  2. Raise and support the vehicle.
  3. Remove the tire and wheel assembly.
  4. Remove the front wheel hub extension (dual wheel vehicles only).
    • Insert a drift or large screwdriver through the brake caliper into one of the brake rotor vanes in order to prevent the rotor from turning.
    • Mark the relationship of the front wheel hub extension to the hub
    • Remove the front wheel hub extension bolts
    • Remove the front wheel hub extension from the vehicle. It may be necessary to tap around the perimeter of the hub extension with a rubber mallet to loosen it from the hub
  5. Mark the relationship of the rotor to the hub.
  6. Remove the caliper and mounting bracket as an assembly.
  7. Hang the caliper and the mounting bracket assembly from the suspension using mechanics wire.
  8. Remove the rotor.
  9. If the rotor is difficult to remove due to corrosion in the hub area use the following procedure to remove the rotor (25 series only).
    • Clean all the surface areas and the threaded holes of contamination
    • Generously apply penetrating oil or the equivalent to the hub/rotor area
    • Insert (2) M10 x 1.5 bolts (jack screws) into the threaded holes of the rotor
    • Tighten both bolts evenly to force the rotor from the hub.
c3692a2.gif
To install:
  1. Clean all rust and contaminants from the both side of the rotor and the hub flange.
    NOTE If the rotor was removed using the jack screw method you must ensure that the hub flange is free of nicks or marks caused by this procedure. Remove all raised nicks or marks before installing the rotor.

  2. Install the rotor.
  3. Install the caliper and the mounting bracket as an assembly.
  4. Install the tire and wheel assembly.
  5. Remove the safety stands.
  6. Lower the vehicle.

Oct 25, 2009 | 1999 GMC Sierra

1 Answer

I need to know the procedure for r and r on a front rotor if this is something that can be done at home with limited tools?


1999 Taurus/Sable Section 06-03: Brakes, Front Disc 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Disc Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Be careful to avoid damage or interference with caliper bleeder screw fitting and front disc brake rotor shield (2K004).
  1. ani_caut.gif CAUTION: Handle front disc brake rotor (1125) and disc brake caliper (2B120) assembly in such a way as to prevent deformation of front disc brake rotor , and nicking, scratching or contamination of brake linings/rotor surfaces.
    NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .


    Remove caliper anchor plate bolts and discard. Position disc brake caliper out of the way. Prevent separation of caliper housing from anchor bracket because contamination of guide pin journals can occur.
  1. NOTE: If excessive force must be used during front disc brake rotor removal, the front disc brake rotor should be checked for runout prior to installation.


    If additional force is required to remove front disc brake rotor , apply Rust Penetrant and Inhibitor F2AZ-19A501-A or equivalent meeting Ford specification ESR-M99C56-A on front and rear rotor/hub mating surfaces. First, strike front disc brake rotor between lug bolts (1107) with a plastic hammer. If this does not work, attach 2-3 Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor . Remove front disc brake rotor from wheel hub (1104) assembly by pulling it off the lug bolts.
Installation
  1. If original front disc brake rotor is being installed, make sure rotor braking and mounting surfaces are clean.
  1. ani_caut.gif CAUTION: Failure to clean rust and foreign material from rotor and hub mounting faces when installing new or old front disc brake rotors will result in high rotor runout, which will speed up the development of brake roughness shudder vibration.
    Apply a small amount of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A to pilot diameter of front disc brake rotor.
  1. Install front disc brake rotor on wheel hub assembly.
  1. Install disc brake caliper and new caliper anchor bracket bolts on front disc brake rotor . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: Failure to tighten lug nuts (1012) in a star pattern may result in high rotor runout, which will speed up the development of brake roughness, shudder and vibration.
    Install wheel and tire assembly on vehicle. Tighten lug nuts to 115-142 Nm (85-104 lb-ft) using Rotunda Accutorq® Lug Nut Socket 164-R0303 or equivalent on a 1/2 inch air impact wrench, or use a torque wrench.
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.
  1. Road test vehicle.









May 25, 2009 | 1999 Mercury Sable

3 Answers

2006 subaru legacy remove front brake rotor


Hello, hope this info helps...(subytech1)...



REMOVAL
15-INCH TYPE

  1. Lift-up the vehicle, and remove the front wheels.
120334720


  1. Remove the caliper body and the support from housing, and suspend it from strut using a wire.
120334721


  1. Remove the disc rotor. NOTE: If the disc rotor seizes up within hub, drive the disc rotor out by pushing with an 8 mm bolt in holes B on the rotor.
  2. Clean mud and foreign particles from the caliper body assembly and the support. 16-INCH TYPE Refer to 15-inch type. 17-INCH TYPE Refer to 15-inch type.
INSTALLATION

  1. Install the disc rotor.
  2. Install the caliper body and the support to housing. Tightening torque: 80 Nm (8.2 kgf-m, 59 ft. lbs.)
  3. Install the front wheels.

Mar 27, 2009 | 2006 Subaru Impreza

1 Answer

1998 honda civic front rotor replacement


Varvah, front rotor: Jack up the car, put on safety stands, remove wheel, remove caliper mounting bolts (2), hang caliper in place w/ bungy cord, rope, etc. so you don't stress the brake line, remove caliper mounting bracket bolts, remove bracket from rotor, remove retaining screws on the front of the rotor, remove rotor. If it's stuck, get 2 - 8x 1.25 mm screws (longer version of what u removed), tighten them in the rotor, they will push it off easily. Reverse to install, tighten bracket to 80 ft lbs, caliper to 20 ft lbs. Let me know if u need more info. Countrycurt0

Oct 09, 2008 | 1998 Honda Civic

Not finding what you are looking for?
2000 Suzuki Esteem Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...