Question about Cars & Trucks

Open Question

Bought rivet gun model 30703 did not inst manuai

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change a wheel on a piece of rollon luggage?


if you have a rivet gun you might be able to change it out (pry the old rivets out and attach the new wheel). Remember though that handyman guns are lightweight and the new rivets will probably not be as strong as the originals.

Dec 19, 2014 | Cars & Trucks

1 Answer

Windowregulator replacement


take off the door card in the door inside .may have been fitted with rivets if so you will need a rivet gun and some rivets.

Dec 11, 2013 | 2001 Cadillac DeVille

1 Answer

I need to get the front passenger side factory installed power window motor out to install a new one how do i do this. after I remove the rifts


rifts? I am assuming you mean rivets, you will need to drill them out and the either rivet the new motor in or bolt it the choice is yours, if you decide to rivet then Walmart carriers the rivet gun and rivets or any hardware/home improvement store. Good Luck Tim

May 22, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

How do i remove the power window motor on my 1992 deville?


take glass out of door there are 3 large rivets holding motor to the door they have to be drilled out to remove motor. To replace use 1/4 20 nut and bolt with lock washers. Or buy large rivet gun and rivets.

Dec 17, 2009 | 1992 Cadillac DeVille

1 Answer

How do you remove the window regulator from 1992 ford taurus? He removed the bolts, but it appears there's rivets or something still holding the regulator/motor on. Do we need a special tool or something?


Yes, four rivets hold the regulator in place. You will need large rivet gun and some long reach rivets. The rivets are available from most parts stores (NAPA).
Punch the center of the rivet out and remove the head.

Oct 18, 2009 | 1992 Ford Taurus

1 Answer

How to replace exterior door handle on the back passenger side. What tool is needed?


there are two rivets that you will have to drill out. on the inside of the door, there is a threaded clip that holds the linkage in, you will have to open it (it opens like a door, it may be a little stubborn, but it will open). then put your new handle on, and then the linkage back in, and snap the clip back in place. you will need one of the bigger pop rivet guns because the rivets are 1/4 ones. also, when you go to rivet the handle back on, tape some cardboard under the handle. that way if the rivet gun drops after it snaps off the rivet, it will not scratch the door. hope this helps you.

Oct 14, 2009 | 2000 Ford Explorer

1 Answer

HOW TO REPLACE WINDOW MOTOR ON 02 PONTIAC SUNFIRE


I replaced the window motor on the drivers door on my 02 Sunfire.
was a big pia .. you have to drill out the huge pop rivets and squeeze the motor and assembly out of the door.. The motor is then again riveted to the arm assembly. I used bolts to put the motor back on the arm, but had to buy the big pop rivets and a big pop rivet gun to put the door back together.. All in all a big PIA.. I would take it to a shop.. imo..

Jul 23, 2009 | 2002 Pontiac Sunfire

1 Answer

Plastic Guide rail on sunroof broke


I just purchased a used yukon xl. Both plastic rails are broken.
Solution: Drill out the blind rivet. Start with 1/8 drill bit and remove the head off. The plastic broken part can now be removed.
Install a blind rivet through the new plastic rail and use the rivet gun to squeeze the rivet in place. Make sure it is the right length.
get a grip gage and determine the right rivet for it.
very easy job.

Jul 01, 2009 | 2003 GMC Yukon XL

1 Answer

How to replace auto lock/unlock actuator on 5th door of 99 Chevy Tahoe. panels are off, looks riveted on.


some are bolted, but most are riveted,you need to drill them out and replace them with special rivets,5/16x7/16 all gm bodyshops have them 75cents to $1 each, but you need specail heavy duty rivet gun ,you will pay between $65-$100 for the rivet gun, if you have a friend at a local bodyshop i would borrow it with a deposit ,they get there gun back you get you cash back,hope this was helpfull

Jun 28, 2009 | 1997 Chevrolet Tahoe

1 Answer

Celica fuel doors problem !!!


first you will have to take a small punch and knock out the center and then drill the rivet out.and then you will have to put new rivents to hold the door back on. You will have to have a rivet gun and 2 rivits to fit the hole

Jan 08, 2009 | 2003 Toyota Celica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...