Question about Mercury Milan

Open Question

How to replace valve cover gasket on 2008 Mercury Milan 2.3

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: 1997 Camry Valve Cover Gasket Replacement

Removal of the plenum is pretty straight forward. You will need to replace the plenum gasket after you remove it; the gasket is not reusable. Personally, if I was going to take the trouble to remove the plenum, I would replace the plugs and wires back there, also.
I know, I have a 93 Camry V6, and it is a real pain to do the plugs and wires with the plenum on. There are no secrets or great tips on the plenum removal, just take your time. Remember that there are different size bolts, and where they go. Please get back to me if you need any more info...Hope this helps, and thanks for choosing FixYa to resolve your issue.
The graciousness of a FixYa rating for my assistance would be greatly appreciated.

Posted on Dec 15, 2008

Ad
leetamara
  • 702 Answers

SOURCE: valve cover gasket leaking

When you buy the valve cover set, it will include the spark plug well "O" rings. Simply remove the valve cover and on the underside of the valve cover, you'll see the "O" rings that need replaced and you'll see exactly how the valve cover gasket itself fits.

Posted on Feb 12, 2009

  • 1 Answer

SOURCE: replace valve cover gasket

I have the same problem on a 2003 Town & Country. The cover for the front 3 cylinders is quite straight forward, but in order to do the rear cylinders I believe you are going to have to remove the cowling below the windshield. You will need a gear puller to remover the windshield wipers first, then remove the cowling. Than should give you more room to work. It's still not going to be easy, but it sure beats paying hundreds of $$$$ in labor charges.

Posted on May 04, 2009

  • 61 Answers

SOURCE: how to replace valve cover gasket 1998 chevy malibu

The first step is to remove all the parts that are in the way of you being able to remove the valve covers. (Ex.: air intake, loose wires etc.) Then you will need to remove your valve covers (using basic tools) and be very careful to not let anything get on your lifters, which your valve covers protect. Once you have the valve covers off compare the new gaskets to make sure they are the right size. Then remove the old gasket and replace with the new one using a high temp gasket sealant (available at any auto parts store) to attach the gasket to the valve covers. Then tighten down snug and check for leaks after replaced. 

Posted on May 06, 2009

Biggdex35
  • 333 Answers

SOURCE: how to replace a valve cover gasket 2003 hyundai santa fe

Just take a picture of it with digital camera or phone. And start removing wires and hoses until they are all out of way of cover. Then remove the bolts all way around cover and pull straight up and it will come right off. If not use a flat head screw driver to prise it off. Clean old gasket off of valvecover and engine. then put it bak together. Tighten bolts slowly, start with ones in center ov it and work your way out. Just finger tight. Then snug, then torque em down. Not too tight as if tostrip the bolt or break it off. Cause it be very expensive. also write down everywhere each wire go's unless you can remember

Posted on May 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a mercury 2008 milan and my rear passenger brake just locked up, what can i do to fix problem


Pull the wheel off and inspect the brake, it could have a defective caliper piston, the other issue can be a defective Antilock brake system hydraulic control valve.

Sep 19, 2016 | 2008 Mercury Milan

1 Answer

How to bleed the brakes on a 2008 mercury milan with ABS


Two people start at the front brakes and finish on the rear,pump the pedal up then open the bleeder ,hold pedal down while locking off the bleeder ,do the same on all brakes,check the ABS unit it could have bleeder valve ,s on it as well,keep the master cyl .full while bleeding to stop air entering .

Apr 15, 2016 | 2008 Mercury Milan

1 Answer

2008 mercury milan won't shift into gear is this due to the sensor on the brake pedal arm


what sensor??did you do something and now it wont shift??there is an interlock on the shifter that goes bad

Jun 20, 2015 | 2008 Mercury Milan

1 Answer

2008 mercury Milan premier-po356-missing # 6 cylinder no voltage to spark plug coil what controls voltage to coil


Unless yours is different from most, there is an ignition module which can fail in several ways, and is a common failed item. Failed wiring to coil also possible.

Apr 29, 2015 | 2008 Mercury Milan Premier

1 Answer

Where can i get the wiring diagram for 2008 mercury milan


http://www.fordfusionclub.com/showthread.php?t=386456

Jul 22, 2014 | 2008 Mercury Milan

1 Answer

Why does 2008 Mercury Milan die at idle ?


Dirty IAC valve, sticking EGR, bad O2 sensor, bad coolant temp sensor, tune up items.

Jul 22, 2014 | 2008 Mercury Milan

1 Answer

Replace pads and rotor on 2008 milan


jack car, block wheels and use jack support.
remove tire
unbolt tire
remove caliper
use a C clamp to compress caliper and make room for new pads
remove old rotor and install new one
install new pads in caliper
install caliper
install tire

Nov 11, 2013 | 2008 Mercury Milan

1 Answer

I have 56000 on a 2008 Mercury Milan and my check engine light is on. Coil #4 has been replaced and still having problems.


What problems-cylinder misfires

Just because #4 coil was replaced,
does not mean you got all the bad
ones or that #4 was bad

Apr 02, 2013 | 2008 Mercury Milan

1 Answer

Where is PCV valve located on 2008 Mercury Milan 2.3 L I4 cylinder? Do you have a diagram you could send?


On valve cover on almost all vehicles

YOU NEVER NEED TO REPLACE A PCV VALVE

EVER


They have NO EFFECT ON YOUR ENGINES PERFORMANCE

They regulate crankcase vacuum only SO FORGET IT

Aug 06, 2011 | 2008 Mercury Milan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...