Question about Cars & Trucks

2 Answers

I have a dodge Durango and while driving it lost power and shut of, the rpm needle went back and forth before dying, tried to restart and it wouldn't, waited awhile tried again it start. This has Been going on for a couple of days and engine light on. I scanned it and i got error code p0340 which is camshaft and p0700 which is the tcm malfunction.. I changed the camshaft and replaced Battery and cleared codes but I'm still getting p0700 with engine light on and truck runs fine except it keeps shutting off while driving, could it be the input or output sensors for the transmission..?

Posted by on

Ad

2 Answers

Hi! The TCM code is the transmission control module, you would need an advanced scan tool to diagnose this problem. Changing parts can be quite expensive and also may be a wiring issue. Would be wise to put in the shop if you don't have the proper equipment. Good luck

Posted on Nov 16, 2013

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 29 Answers

Did you replace the cam position sensor?

Posted on Nov 16, 2013

  • rachael_luci Nov 16, 2013

    Yes i did...cleared the codes and engine light turned off..drive it around it ran fine but again it shut off engine light canned back on and still have a p0700 (tcm)

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

leetamara
  • 702 Answers

SOURCE: My 2002 Dodge intrepid has it engine light on

The MAP sensor and Knock Sensor are both very easily replaced. A better scanner will tell you which sensor is going bad on your transmission. An Autozone code reader will not tell you which sensor on the trans. is acting up. Most sensors on your trans. are very easity replaced as well. They just screw in and plug it. It's worth paying to get a "real" scan done. The trans. sensors are inexpensive and you can replace any other your listed sensors yourself.

Posted on Jul 11, 2008

  • 15 Answers

SOURCE: 2002 pt cruiser Camshaft Sensor

change the crankshaft positon sensor in the rear of the engine above the oilfilter. Also check the wiring to this sensor, they have a problem shorting out. You have to change the camshaft and crankshaft sensors at the same time. Make sure you give your car a major tune up. Did you check yor starter?.........runjoe

Posted on Mar 04, 2009

crayzeetrayn
  • 837 Answers

SOURCE: 2001 Jeep Grand Cherokee code P1391

I would check to be sure that the timing chain hasn't jumped at all ..

Posted on Mar 25, 2009

emissionwiz
  • 76846 Answers

SOURCE: engine code p0700 need help

I have been diving into my factory service manual, and the P0700 should have another trans trouble code stored with it, a "Generic" code reader may not be able to read the other trans code, if it after a trip to the dealer to sort out this code turns up nothing (no other stored codes) then there may be a problem in the TCM (Transmission control module) so u should get this to the dealer and have them read the codes and report them to u.

Posted on May 15, 2009

c17hydro
  • 2984 Answers

SOURCE: Camshaft Position Sensor

P0340 Camshaft Position Sensor "A" Circuit Bank 1 or Single Sensor

P0700 Transmission Control System (MIL Request)

The code P1684 is real easy. The computer is stating that the battery has been disconnected within the last 50 starts.

Posted on Jun 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Starts and shuts off when I stop at stop sign or light.


dodge dakota idling and dying - CarGurus

www.cargurus.com > Questions > Dodge > Dakota

CarGurusApr 12, 2011 - dodge dakota idling and dying - My dakota will start then idle down and die. ... I have a 1992 dodge dakota that dies on me at stop signs and when I take my foot off the gas pedal. ... Had the same problem with my 98 Dakota.

Dodge Ram 1500 Questions - 1998 1500 5.2 Shuts Off ...

www.cargurus.com > Questions > Dodge > Ram 1500

CarGurusAug 29, 2011 - 1998 1500 5.2 Shuts Off Randomly - does anyone have an answer to the mysterious shutting ... 1998 1500 5.2 that shuts off randomly and if i wait a few seconds to minutes it will start again. ... does it do it when coming to a stop or when taking off from a stop or shifting from drive to .... Used Dodge Dakota".

Truck Shuts Off - 1998 Dodge Dakota - RepairPal

repairpal.com > Questions > Dodge > Dakota > 1998 Dodge Dakota
I have a 91 dodge dakota truck with a 318 motor, 249,000 miles, it will start up thenshut right off when I take my foot off the gas pedal, I had a tune up a month ...

2000 Dodge Dakota idle then dying problem FIXED - YouTube

? 4:05
https://www.youtube.com/watch?v=XRVQEdnei34
Mar 26, 2014 - Uploaded by AoDMADPenny
It would rev up then back down to about 200 rpm then just shut off. ... My Dakota dies during idling right after i start it up and then it wont start back up again. .... 1998 Dodge Durango No Start or No Bus or Randomly Stalls ...

Jan 06, 2016 | 1998 Dodge Dakota

1 Answer

2003 dodge durango while driving lost acceleration, shut it off, restarted then drove fine for about 4 miles did the same thing but this time it didn't want to start. After a couple minutes it started


sounds like the crankshaft sensor gets warm and then opens up, once cooled off it closes again ( it is a transformer in epoxy housing ) I would replace it.

Apr 28, 2015 | 2003 Dodge Durango

1 Answer

2006 dodge durango shut off while driving, lost all power. Tried to restart, check engine light starts blinking. What could be the problem?


Go to nearest autoparts supplier and they usually will scan for codes free of charge, and point you in right direction of part(s) required to correct the problem . If your still not sure, write down the codes and get back to me/us.

Mar 02, 2014 | Dodge Cars & Trucks

1 Answer

P0123 and p0068 on a dodge durango 2007


P0068 - MAP/MAF Throttle position correlation
P0123 - Throttle positon sensor/Swtch A Circuit high input

Nov 07, 2013 | Cars & Trucks

2 Answers

I lost the remore to my Dodge Durango. The keys


Try lock the car back up, with key unlock car, try it on both sides. Some times that will disable the theft system.

Jun 04, 2010 | 1999 Dodge Durango

1 Answer

2004 Durango dies and shifts weird


I will try to help..ihave a 2000 dodge durango with the 4.7 v8..My trans started shifting funny and the rpm's would go up to 2000+rpm when i was driving, which means i was getting really crappy gas mileage at 40mph..took it to shop, engine light on,put it on machine to diagnose..got a generic p0700 code plus a couple others..code basically says tranny is fn up..
Try this a cheap fix first that worked for me..on the transmission,driver side there are two sensors..input/output transmission speed sensors..to be exact..they send info to computer to regulate shift points in trans..upshift and downshift..replace them both although one may be the culprit..cost at the dealer here in Delaware was $40.72 for one..there is one bolt(8mm)and one electrical connection to each..time to replace both about 15minutes you don't even have to jack up truck but you will have to get underneath.

Hope this helps and good luck..if you change them and find the tranny shifting properly..cycling the on and off switch will eventually turn off the engine light..just drive it normally i mean..go here shut it off..get back in start it up and go..it will go out..good luck

May 10, 2010 | 2004 Dodge Durango

1 Answer

2005 dodge durango driving down the road,


Are you actually hearing the engine speed change as well when this happens, or just seeing the tach needle make crazy readings??

If only the tach is being funky, then I would say a speed sensor on the tranny is on its way out. There is also a speed sensor on the rear axle of some Durangos that can cause this issue.

Apr 21, 2010 | 2005 Dodge Durango

1 Answer

My drivers side power seat moves slides back and


No the adjusters for power seat are made from some steel and a lot of aluminum parts. Replacing the seat tracks are your only option to be safe for they are riveted together

Apr 03, 2010 | 1999 Dodge Durango

1 Answer

2004 dodge durango engine shuts off while driving


I had this happen to me before. My battery had went out and I had put another in (didn't buy a new one-- it was holiday). It did this exact thing to me. The scary part is once, it was on the interstate going about 75 mph... didn't die but all gauges went to nothing. It turned out that the battery I was using didn't have enough cold cranking amps and was pulling down the alternator too much so the computer shut it down. The one time it didn't... it was because the RPH's were too high. Try checking the battery and alternator... make sure you have the right battery and have an alternator shop test your alternator if the battery is good.

Nov 17, 2008 | 2004 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...