Question about 2004 Chevrolet Malibu

Open Question

Where is the map sensor located on a 2004 chevy malibu 2.2

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: 1998 chevy suburban map sensor

Hi, The Map sensor on a Suburban is located.
Beside of the ignition coil. on the intake.
Is a litle sensor with a connector of 3 wires.

I hope this work for you. OK

Posted on Jul 03, 2008

Ad
lasvegasrich
  • 65 Answers

SOURCE: replacing spark plugs on a 2004 chevy malibu

2.2L Engine

  1. Observe the following service precautions:

    Allow the engine to cool before removing the spark plugs. Attempting to remove spark plugs from a hot engine can cause the spark plugs to seize. This can damage the cylinder head threads. Clean the spark plug recess area before removing the spark plug. Failure to do so can result in engine damage due to dirt or foreign material entering the cylinder head, or in contamination of the cylinder head threads. Contaminated threads may prevent proper seating of the new spark plug. Use only the spark plugs specified for use in the vehicle. Do not install spark plugs that are either hotter or colder than those specified for the vehicle. Installing spark plugs of another type can severely damage the engine.
  2. Turn the ignition OFF .
  3. Disconnect the Electronic Ignition (EI) module harness connector.
  4. Remove the spark plugs using a 5 / 8 inch spark plug socket.

To install:

WARNING Do not coat spark plug threads with anti-seize compound. If anti-seize compound is used and spark plugs are over-torqued, damage to the cylinder head threads may result.
  1. Inspect the gap on the new spark plugs, re-gap the plugs as required. The spark plug gap specification is 42 inch. (1.0 mm).
  2. Install the spark plugs and tighten to 15 ft. lbs. (20 Nm).
  3. Apply dielectric compound to the spark plug boots and make sure no corrosion is present.
  4. Install the ignition coil housing to cam cover and attachment bolts.
  5. Tighten the ignition coil housing bolts to 89 inch. lbs. (10 Nm).
  6. Connect the EI module harness connector. Push in until a click is heard and pull back to confirm a positive engagement.

Posted on Oct 07, 2009

Testimonial: "Thanks for the help, it was easy to change out the plugs with your info."

dttech
  • 4803 Answers

SOURCE: where is the bank 2 sensor 1 located.

Oxygen sensors are always numbered like this:

Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2

some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.

Sensor 1 is always the upstream sensor (The one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.

Most GM engines have #1 cylinder located on the left bank, (or Driver's Side) of the engine,

So, the answer to your question would be that you are looking for the sensor located before the catalytic converter on the right (or Passenger Side) of the truck.

Posted on Oct 17, 2009

  • 462 Answers

SOURCE: oil filter location 2004 Chevrolet Malibu Classic

Standing at the front of the car looking at the intake manifold, its on the right hand side of the manifold about 6 inches down from the valve cover under a black cap with a 32mm top on it.

Posted on Jan 04, 2010

  • 212 Answers

SOURCE: where is knock sensor located on 2004 chevy 2500Hd

Under intake manifold on top of block,you need to remove intake to access sensors there are two of them you can't miss them when intake is off. After replacing sensors you need a new intake gasket.

Posted on Apr 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of MAP sensor on 2002 Alero GX 2.2?


Oldsmobile Alero MAP Sensor - PartsGeek.com

www.partsgeek.com > ... > Oldsmobile MAP Sensor > Alero Parts
Oct 29, 2008 - 04 2004 Oldsmobile Alero GL MAP Sensor 3.4L V6 VIN: E Delphi · Click to Enlarge ... Vehicle, Engine. • 2002 (02) Oldsmobile Alero, 3.4L V6. 04 2004 Oldsmobile Alero MAP Sensor 2.2L 4 Cyl Standard Motor Products.

Part 1 -How to Test the MAP Sensor (GM 2.4L Quad 4)

troubleshootmyvehicle.com > GM > 2.4L
Jun 7, 2011 - GM 2.4L MAP Sensor Test with a Multimeter. ... 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002. Malibu 2.4L. 1997, 1998 ... Alero 2.4L. 1999 .

Nov 08, 2015 | Cars & Trucks

1 Answer

Where is the MAP sensor located on a 2004 Chevy Cavalier 2.2 ecotec dohc?


On your intake manifold, #3 in diagram. My info showed two wires, one is gray, the other is orange with black tracer.

Nov 11, 2014 | 2004 Chevrolet Cavalier

1 Answer

What does p0430 code mean in a chevy malibu?


it is the o2 sensor next to the catalytic converter which is the bank 2 sensor

Oct 30, 2012 | 2004 Chevrolet Malibu

1 Answer

Where is the map sensor on a 2010 chevy malibu 2.5 engine located


aThis forum has a picture of the MAP sensor labeled in the engine compartment, about 1/2 way down the page.

Oct 03, 2012 | Chevrolet Cars & Trucks

1 Answer

Where is maf sensor located on a 2004 chevy trailblazer


There is no MAF sensor. The MAP sensor is on the drivers rear of the intake plenum on top. Its the only sensor on top of the plenum. Speed density, not sure what you are talking about? Lmk

Mar 04, 2012 | Cars & Trucks

1 Answer

Map sensor replacement


On top of the intake near the fire wall

Mar 05, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

Runs rough at idle and low rpm. misfires. gets better @ high rpm


sounds to me you have a emissions problem check your EGR valve and MAP senser

Dec 28, 2008 | 2004 Chevrolet Malibu

1 Answer

2.2 engine


Hello I have been trying to locate the map sensor on my 2005 chevy malibu with a 2.2 v4 engine and i can ot locate it. please help me

Oct 05, 2008 | 2005 Chevrolet Malibu

Not finding what you are looking for?
2004 Chevrolet Malibu Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...