Question about Cars & Trucks

Open Question

Slave cylinder diagram

1991 Toyota Previa. Slave cylinder for clutch will not bleed. Replace it?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1056 Answers

SOURCE: replaced clutch slave cylinder blew

Could be a couple of different things.
1) your clutch master has a plugged pressure bypass, and it is sending excessive pressure to the slave and blowing it out.
2) The clutch throw out arm is bound, and will not allow the slave to compress it.
3) The replacement slave was defective.

What was the reason for replacing the slave in the first place?

Posted on Jul 31, 2008

Ad
  • 275 Answers

SOURCE: Bleeding clutch slave cylinder

if you loosten the slave bleeder screw and push in the clutch pedal fluid should come out if not make sure someone holds down the pedal and tighten the screw then pump the clutch a few times and hold the pedal and open the screw if no fluid repeat a couple of times if still no fluid you need either a new master cylinder or just rebuild it( normally cheaper) and if you rebuild it make sure you flush all the lines of debris

Posted on Nov 12, 2008

autodr
  • 260 Answers

SOURCE: Bleeding clutch slave cylinder

i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Posted on Nov 15, 2008

  • 2187 Answers

SOURCE: Bleeding Clutch Cylinder with no bleeder screw

I have not tried myself but see if the link below will work for your case. It is not the same model as you have but most vehicles have the same components for the non electronic parts. http://www.2carpros.com/forum/1988-dodge-dakota--bleding-air-out-of-clutch-master-cylinder-vt248517.html

Posted on Jun 04, 2009

  • 1 Answer

SOURCE: 1999 pontiac sunfire bleeding clutch

my 1999 pontiac sunfire drivers door latch is broke can not close the door. i have it pulled shut? how much will a used latch cost, or even 3 bolts for it? all the auto stores/ jumk yards are closed for me to call

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to bleed the air out of the clutch line on a Toyota Previa... Where is the bleed


One is on the slave and one is on the clutch master cylinder.
Do the master first-at the bleeder or at the line 3 times.
Then go to the slave cylinder.
Do not pump the pedal-just old it down to bleed.
the slave may not have a bleeder screw- just crack the feed line to bleed it.

Mar 02, 2013 | Toyota Previa Cars & Trucks

1 Answer

My 1993 Toyota 1/2 ton pick up has had a clutch issue recently. When the vehicle is on and running, the clutch will sink to the floor and it cannot even be forced into gear. When the vehicle is off, the...


Check the condition and operation of the slave cylinder. If the reservoir is low on fluid and the slave cylinder is leaking at the rod, replace it and bleed it at the slave. This is a common problem with a Toyota where the slave cylinder creates a leak. If the slave was fine, then the clutch needs replacement. have a good day !!

May 31, 2011 | 1991 Toyota Pickup

2 Answers

My clutch doesn't always disengage when the peddle is on the floor and when starting out in first bolts ahead as though the clutch was already part way out. I took it to a shop and they said my clutch...


your clutch master cylinder is right beside your brake master cylinder. I would advise you to replace the master cylinder and the slave cylinder together. The slave cylinder is on the side of the transmission. The slave cylinder does have a bleeder screw on it after the parts are bolted in place fill with dot 3 brake fluid and open the bleeder on the slave cylinder until fluid starts dripping out. Then tighten bleeder then open bleeder and have someone push down on clutch pedal while the pedal is pushed down tighten the bleeder the release pedal. Repeat this procedure until you get no air and the pedal feels normal and you should be good to go. Good luck!

Apr 14, 2011 | 1991 Toyota Celica

2 Answers

Replaced whole clutch and slave cylinder on 1996 Toyota T100 2wd 2mos. ago. Today while driving the clutch hit the floor. I did'nt see any fluid leakage. Any ideas.


Sounds like you need to bleed the system again, or you have an air leak. try bleeding again and just check your fittings for tightness.

Jan 20, 2011 | Toyota T100 Cars & Trucks

1 Answer

Clutch has to be pushed to the floor before you can shift without grinding gears.1991 Toyota 4x4 truck


Check your hydraulic clutch slave cylinder on the transmission for leakage and check the reservoir fluid level. If the reservoir has run low, you may have air in the lines. If the slave is leaking, replace the slave and bleed the system. Let me know if you need instructions or have more questions.

Sep 28, 2010 | 1991 Toyota Pickup

1 Answer

Replaced master and slave clutch cylinders but


if you replace and shure to make a good bleed on clutch fluid, then replace clutch disc

Jul 27, 2010 | 1991 Toyota 4Runner

1 Answer

Changed clutch but unable to bleed the slave cylinder. Does that mean clutch master cylinder is bad? Got one from parts store but can't figure out how to take the clutch safty switch off to change it. Any...


Probably not. Bleeding clutch slave cylinders is tricky because you cant "pump it up". The master cylinder has no static valve so the best way to bleed the slave cyl. is to use gravity. Fill the master cylinder reservoir and open the bleed valve on the slave cyl. Allow fluid to drip into an open can until there's no trace of air. Close bleed valve and try clutch. If still no pedal, repeat the process. This is quite an acceptable procedure.

Mar 22, 2010 | 1991 Chevrolet S-10

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

1 Answer

Replace slave cylinder on 89 toy.corolla sr5


If it was selecting gears ok before the clutch was replaced then the slave cylinder should be ok, it may just need bleeding. If it was playing up before, you can get them rebuilt by a brake specialist or a wrecker would be a cheaper option. They are very easy to replace, hardest part is bleeding them which is what I suspect is wrong with yours.

Mar 25, 2009 | 1989 Toyota Corolla 2 Door

2 Answers

2000 honda accord clutch problems


There is air in the system. The slave cylinder does provide pressure to return the pedal. Check to be sure that you have plenty of fluid in the master cylinder (clutch). Slowly work the pedal back and forth to try and remove air. (This usually works unless you have really lost all fluid. Once the air is remove depress the clutch while in gear. If it does not keep the car from moving then replace the slave and master cylinder. The parts are a little over $100. Hope this helps. I have one in the shop right now as a matter of fact...

Jul 01, 2008 | 1991 Toyota Previa

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...