Question about Cars & Trucks

Open Question

I have a BFP- 703CH since 2009. Yerterday I try to

I have a BFP- 703CH since 2009. Yerterday I try to blend fruts and a noice come on. I took the back cover out and found that the fan or something like that is loose. I can't find any other part that maintain in place the fan. Apparently that part is missing. What can I do.

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What causes my 3 door pajero 2.5 tha fter 5 mins after start something there is knocking noice as if something is touching the timing belt cover

could possible be just that remove the timing belt cover and turn the engine over by hand as it may be the timing belt coming apart.

Mar 29, 2015 | Mitsubishi Pajero Cars & Trucks

2 Answers

Blows cold air with heater on

It's most likely the "blend door", which moves back and forth between the a/c or vent position, and the heater position. There is an electric motor that moves plastic gears back and forth to adjust the temperature, and it is common for the largest gear to crack. When this gear breaks, or something else causes the mechanism to disengage from the blend door, it tends to fall to the full cold position. If you want to try to fix it yourself, you can get to it by removing the four screws holding the change drawer/ashtray. The mechanism is towards the right side, behind the glove compartment. It has a knob in the middle of it that you should see move (use a flashlight) when you adjust the temperature. You may be able to twist it by hand if it's broke, and if the fan is on full blast, the air will hold it in this position until you turn it off and it falls back to the cold position. Here's a link I found that is more in depth:
Thread No heat in your Roadie Read on

Jan 08, 2014 | 1992 Buick Roadmaster

1 Answer

There is this bang noice that comes from theroof top of the center pillar point whenever the car make a sharp turn

Has the car got a sunroof? If so, it sounds like something is a bit loose and sliding sideways when you turn the corner..

Oct 10, 2013 | 2009 Mercedes-Benz E-Class

1 Answer

My 2000 Grand cherokee only blows warm air from defrost or any vent, 105 to 110 on a 32 degree morning with high fan, about 10 degrees warmer on low fan. It gets warmer when it warms up outside.Engine...

This is a common problem with WJ Grand Cherokees, it's called a "Blend Door".

In the heating and cooling system you have doors that open and close to give you warm and cold air and a mix of both.

What you have is an arm that pulls a door with peg on top, the peg tends to snap off. As you said your dealer replaced the blend door or doors I would take it back as is has blend door all over it.

Yahoo and youtube "jeep grand cherokee blend door repair"

I had a 02 limited blend doors issues (note the issueS) and was lucky to have it still covered.

I do hope this helped.


Nov 24, 2010 | 2000 Jeep Grand Cherokee

1 Answer

The lower glove box on my 2009 Rav4 won't close. It feels like something has fallen behind it. How do I remove the glove box door?

I had the same problem with my 2009 RAV4 lower glove box. I removed the box by popping the top front right post and then the top left front post from theside housings by prying them free with my fingers. They pop out easily. I then let the box fall open and while holding it level to the floor, pulled forward, released the piston from the post on the right, and the glove compartment came out without tools. There was a plastic electrical box cover, which came loose behind the glove box, blocking it from closing. I snapped the cover plate back in place and then reversed the glove box removal process. It took a few minutes and I needed no tools.

Nov 05, 2010 | 2009 Toyota RAV4

1 Answer

Subaru forester heater

take back to the dealer,hopefully the will find that the blend door cable is off or not adjusted properly

Jun 11, 2009 | 2009 Subaru Forester

1 Answer

A/c motor problem

One of the blend door motors on the A/C Heater assembly may be stuck or defective or one of the linkage arms may have fallen off.Slide under the dash a bit and slide the temperature button.
You may have to take a panel or two off above the passenger/drivers feet area.
Can you see any movement on any linkage or locate the noise at one of the blend door motors?
You might just see a linkage arm off and you may be able to reattach it.

May 12, 2017 | 1994 Nissan Altima

2 Answers

No heat on our 2006 sierra pick up

does the temperature guage go up to normal if so probably either a bad blend door motor or broken blend door or heater core cloged you can check the lines if one is cooler than the other then it is most likely the cause

Dec 31, 2008 | 1999 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides