Question about 2001 Toyota Echo

Open Question

Oil drain plug torque - 2001 Toyota Echo

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the right oil and filter to use on the range2007 hse?


How To Change Oil and Oil Filter on Range Rover Sport or Land Rover LR3

  • Place an oil drain pan below the oil filter and drain plug and unscrew the oil filter.
  • Lubricate the rubber seal with clean oil and install the new filter. Tighten to 13 foot-pound torque.
  • Remove drain plug in the oil pan and drain the oil. Catch the oil in the drain pan. After draining the oil install and tighten the drain plug to 18 foot-pound torque.
  • Fill engine with 5W-30 weight oil. The 4.4 V8 takes 8 quarts; the 4.0 V6 takes 6 quarts. Start engine and check for leaks.
  • Recheck level and top up as necessary.
  • Reinstall the under engine shields / skid plates.

Apr 12, 2015 | Land Rover Range Rover Cars & Trucks

1 Answer

Is it possible for me to change the engine oil as im a new timer on these situations thank you.


"anything is possible"



depending on your vehicle's year make model and engine size, the drain plug and oil filter may or may not be hard to get to



today's era of youtube videos and car owners forums makes it easier than before



look it up to see if it's easy to get your oil filter and drain plug for your car/ truck



SAFETY first! use JACK STANDS & don't rely on the jacks by themselves to hold your vehicle up ~ i've known a neighbor and a co-worker who almost got crushed to death



have backup tools to remove your oil filter in case the previous person didn't lube the o-ring and/or over tighten the filter. i have a strap wrench or correct end-cap oil wrench for my vehicles



depending on how the oil filter is mounted, i usually add some oil right into the filter to get it pre-charged while i also lube that rubber seal/o-ring on the filter....



some say to use NEW oil drain plug gaskets before you torque it down (to specs) each plug has a torque spec; but i got away with re-using it a few times before i replace the gasket.



I spin the drain plug on by hand first to avoid cross-threading ~ then use torque wrench. you don't want this plug to loosen while you're driving on the highway or you don't want to overtighten it and have the threads on the oil pan to strip on you...



do not overfill your vehicle's oil capacity ~ the crankshaft will whip it up to foam, causing your engine bearings to starve for oil



so look up the torque spec for your drain plug, and oil capacity

Apr 09, 2015 | Cars & Trucks

1 Answer

How to change a fuel filter on a polo vivo 2010


Engine oil: Drain or extract and replenish; renew oil filter Engine oil: Drain or extract engine oil ? Chapter. Renewing oil filter ? Chapter. Replenishing engine oil ? Chapter. Draining or extracting engine oil Special tools and workshop equipment required t Used oil collection and extraction unit -V.A.G 1782- t Oil spill cloth -VAS 6204/1- Draining or extracting engine oil Carry out the following procedure: > Note
t For engines with standing oil filter the oil filter must be renewed before changing the engine oil. When removing the filter element a valve is opened, the oil in the filter housing automatically flows into crankcase. t If the engine oil is drained and not extracted with an oil extractor, replace drain plug. This prevents leaks. t Observe disposal regulations! - Extract engine oil using used oil collection and extraction unit -V.A.G 1782-. or - Remove oil drain plug. - Let engine oil drain. > Note
t The oil drain plug is fitted with a secure seal, therefore the oil drain plug must always be renewed. t Observe disposal regulations! - Screw in new oil drain plug with seal hand-tight. - Replenish engine oil, specification ? Chapter. Engine oil capacity: "Power unit" ? Power unit; Rep. Gr.17"Lubrication; oil capacities" or ? Maintenance table. Specified torques for oil drain plug: t Petrol and diesel engines 30 Nm > WARNING
t Torque specifications must not be exceeded. t Excess torque can cause leaks in the area of the oil drain plug or even damage. Renewing oil filter Renewing oil filter, 1.4 l and 1.6 l injection engines > Note
t Prevent engine oil from dripping onto components in engine compartment. t Oil new O-rings before installing. t Observe disposal regulations! Renewing oil filter, 1.4 land 1.6 l engine Carry out the following procedure: alt="W00-10211"> - Unscrew cover cap -1- with socket insert 36 mm AF and remove cover with oil filter insert -4- and valve -5-. - Renew O-ring -2- of cover cap and O-ring -3- of valve. - Renew used oil filter element with new filter element. > Note
Observe disposal regulations! - Tighten cover cap -1-. Cover cap torque setting: 25 Nm. Replenishing engine oil Oil specifications ? Chapter Engine oil capacities: "Power unit" ? Power unit; Rep. Gr.17"Lubrication; oil capacities" or ? Maintenance table. General notes > Note
Observe disposal regulations! - After replenishing with oil, wait at least 3 minutes and then check oil level. - Pull out dipstick, wipe with a clean cloth and push dipstick in again to limit stop. - Pull dipstick out again and read oil level. alt="N01-10183"> For dipstick as illustrated: A - Oil must not be replenished. B - Oil may be replenished. It may happen that the oil level afterwards is in the -A- region. C - Oil must be replenished. It is sufficient if the oil level is in the -B- region (hatched area) afterwards. There is a danger of damaging the catalytic converter if the oil level is above the -A- marking. - If oil level is below -C- marking, top-up oil to -A- marking. alt="N01-10255">
25567142-tnzdbwhiaswbtdy3r1p2vgzs-2-2.png

Mar 14, 2015 | Volkswagen Polo Cars & Trucks

1 Answer

What is the torque for oil plug for 2010 Toyota Venza?


Oil Drain Torque Specs Toyota Nation Forum Toyota Car and Truck Forums

The blog above lists 27 - 30 ft. lbs. torque for the drain plug. As someone in the blog stated, 30 Ft. Lbs. sounds excessive , and I agree. . You can torque the drain plug , but it's not critical to do so. Just snug the plug down. Do not over tighten the plug. It may strip out and it will distort the gasket.

May 25, 2014 | Toyota Sienna Cars & Trucks

1 Answer

What is the torque value for an oil drain plug on a 2006 kia optima


Never heard of anyone using a torque wrench
on an oil drain plug

Kind of silly --just tighten it up
don't go crazy

Do you even own a torque wrench?

Jun 11, 2011 | 2004 Kia Optima

1 Answer

CHANGING OIL ON 2006 GTO, WHAT TORQUE SHOULD THE OIL PLUG BE TORQUES TO


Hello and welcome. here is the oil drain plug torque spec for your vehicle

Oil Pan Drain Plug
25 N·m
18 lb ft

Oct 08, 2010 | 2006 Pontiac GTO

2 Answers

I need to change oil and filter can you tell me oil capacity and drain plug torque? Also what oil filter is best. ken


i like to use mobil 1 oil and oil filters. drain plug torque is wrench tight done overkill it. If it's a 4 cylinder it holds 4 quarts ( with new filter). If it's a v-6 it holds 6 quarts (with new filter).

Jun 22, 2010 | 2003 Toyota Avalon

2 Answers

Where do i put the differential gear oil


Front Differential Oil Change dd7e0eb.gif
  1. Before changing or inspecting oil, be sure to stop engine and lift vehicle horizontally.
  2. With vehicle lifted up, check leakage. If leakage exists, correct it. NOTE: Whenever vehicle is hoisted for any other service work than oil change, also be sure to check for oil leakage.
  3. Remove oil filler plug (2).
  4. Remove drain plug (1), and drain old oil.
  5. Apply sealant to thread of drain plug (1), and tighten it to specified torque.Tightening torque Differential oil drain plug a: 23 Nm (2.3 kg-m, 17.0 ft. lbs.)
  6. Pour new specified oil until oil level reaches bottom of oil filler plug hole (3) as shown in figure. NOTE:
    • Hypoid gear oil must be used for differential.
    • It is highly recommended to use API GL-5 80W-90 gear oil.
Differential oil specification: API GL-5 (For SAE classification, refer to viscosity chart [A] in figure.)

Differential oil capacity (Reference): 0.9 - 1.1 liters (1.9/1.6 - 2.3/1.9 US/Imp. pt.)

  1. Apply sealant to thread of level / filler plug, and then tighten it to specified torque. A: Sealant 99000-31260SUZUKI Bond No.1217G Tightening torque Differential oil level / filler plug b: 23 Nm (2.3 kg-m, 17.0 ft. lbs.)

Jun 04, 2009 | 2007 Suzuki Grand Vitara 4WD

1 Answer

1999 volvo v70 oil change questions


You can buy a canister wrench at the local auto parts store. You do not need to torque the oil filter on, just hand tighten, No new gasket for the drain plugs just do make sure that it is tightened properly

Feb 10, 2009 | 1999 Volvo V70

Not finding what you are looking for?
2001 Toyota Echo Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...