Question about 2002 Dodge Durango

2 Answers

Power door locks

My power locks will not lock any door with the button or the key. It will unlock all doors however.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

This sounds like a bad master switch on the drivers door panel. Have you tried the switch on the passengers front door? If you try that switch and they lock and unlock, then you will need to replace the master switch on the drivers door.

Posted on Nov 17, 2013

Testimonial: "Replaced the master switch. Same result. Does anyone know if there is a module or something that controls the lock feature or if there are override issues?"

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 24 Answers

Dead battery in the key fob/ button battery

Posted on Nov 17, 2013

Testimonial: "I presently don't have a FOB for the Durango. I have ordered a couple and will have to get the programmed at the dealer."

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: Sliding door lock

If you check the doorlock actuator it is more than likely bad. On my caravan I had to replace actuators on both sliders. Cannot get correct actuators at autoparts stores. Either go to a salvage yard or to the dealer to get them.

Posted on Jul 20, 2008

  • 512 Answers

SOURCE: key turns in manual door lock but doesn't unlock truck door

you need to remove the door panel....the linkage for the lock has come disconnected...it shouldnt be too hard to reconnect

Posted on Nov 09, 2008

  • 1 Answer

SOURCE: Remote key fob does not

check the fuse dude it is by driver door side under driver seat.

Posted on May 11, 2009

  • 412 Answers

SOURCE: 2006 Dodge Caravan - ONE power door lock stopped working

i have replaced many sliding door lock actuators on these vehicles..dealer part..mostly on passenger side sliding door..also possible you have a broken wire in door track harness..follow wiring from door into what looks like a plastic chain in door track at door opening

Posted on May 14, 2009

  • 66 Answers

SOURCE: 2004 Dodge Ram 1500 Quad Cab Drivers side power door lock broken

Sounds like the link rod to the latch are jammed in the locked position by something inside the door or it came off. Any way, you have to remove the door panel to get access to it.

Posted on Jun 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Programming keyless entry to 95 landcruiser


1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful
entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons, press the lock button by
itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle once
indicating successful programming. If the door locks do not cycle, or cycle twice.
repeat steps A and B in step 6 as your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Close drivers door.

Oct 29, 2013 | 2008 Toyota Land Cruiser

1 Answer

Power door lock - can't use key to unlock door


need to remove the door panel and check the clips that connect to the locking rods possiblr damaged or disconnected

May 11, 2013 | Buick Regal Cars & Trucks

1 Answer

2001 Mercury Villager keyless remote is malfunctioning


Keyless Entry
The keyless entry system consists of the following:
  • smart entry control(SEC)/timer module
  • keyless entry remote transmitters
  • power door lock actuators
  • body side door power door lock actuator
  • liftgate actuator
  • power door lock switches
  • door ajar switches
  • Principles of Operation
    All doors can be locked at once by turning the door key lock switch to the locked position. An individual door can be unlocked by moving the door key lock switch to the unlocked position and turning it again within five seconds; all the doors (including the liftgate) will unlock.
    The smart lock system is designed to keep the driver from locking his keys in the car. It will lock and then unlock all the doors if the smart entry control(SEC)/timer module detects the following conditions:
    • The ignition key still in the ignition.
    • A front door is open.
    • A door lock switch has been pushed to the lock position.
    The panic feature has a duration of 30 seconds from the last time the PANIC button is pressed. When locking the doors from the remote transmitter, the horn chirp/lamp flash feature can be disabled or enabled by holding the LOCK and UNLOCK buttons for two seconds. The hazards will flash three times to confirm that the feature has be enabled or disabled.
The control module probably see's an input that shouldn't be there . lock Switch , door ajar etc... Don't think it has anything to do with the remote . Some part stores have a tester to see if signal from the remote is working . Or the dealer ! Take it an see if your remote is sending a signal without you pressing any buttons .
If it is you need a new one .

May 19, 2017 | Cars & Trucks

2 Answers

All doors lock with key except drivers door but all will unlock with key (button) 2002 vw passat estate


reset the central locking system by locking car with key in drivers door and hold key over for 30 secs.then pressing and holding down unlock button on keypad OR unlock door with key and hold key over 30secs (windows may go down, thats okay,some cars are fitted with auto windows)then press and hold lock button on keypad.making sure that in both cases you know the keyfob battery is in good nick....should reset system

Mar 03, 2010 | 2002 Volkswagen Passat

1 Answer

I have a 2004 Honda Accord EX. Key Fob works trunk but not doors


Programming
When
Key added or replaced. System malfunction.
How
Obtain all keys. A maximum of 3 keys can be programmed. Close all doors and boot/tailgate. Switch ignition ON. Repeat procedure below 3 times: Within 4 seconds: Press key lock or unlock button. Within 4 seconds: Switch ignition OFF. Within 4 seconds: Switch ignition ON. Within 4 seconds: Press key lock or unlock button. System should now lock or unlock vehicle. Within 4 seconds: Press key lock or unlock button. Within 10 seconds: Press lock or unlock button of first key. System should now lock or unlock vehicle. Press lock or unlock button of second key. System should now lock or unlock vehicle. Press lock or unlock button of third key. System should now lock or unlock vehicle. Switch ignition OFF. Remove key. Check operation of all programmed keys.
NOTE: If less than 3 keys are to be programmed, remove ignition key after programming last key.

Jan 25, 2010 | 2004 Honda Accord

4 Answers

Passlock


turn key all the way on (not to start) let set for 1 hur cycle key and try it.

Jul 20, 2009 | 1999 GMC Jimmy

1 Answer

Step by step reset the door remote control lexus 400LS


1. sitting in driver seat, with driver's door OPEN, press lock/unlock button ON THE DRIVERS DOOR to lock all doors, then manually unlock driver door only.
2. Insert YOUR key in ignition, DO NOT TURN, then remove key.
3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles
4. Shut door.
5. Open door.
6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles
7. With the door open insert your key into the ignition, turn to 'on' position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once by herself). If they don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second, then release the button. The locks should cycle once. If not, start over and go slower.
10. Close the door.
11. Open the door.
12. Press the lock button on the remote. The locks should do a lock-unlock cycle.
13. Close the door
14. Press the lock button on the remote, the doors should lock.
15. Press unlock button and the doors should unlock.

Jun 16, 2009 | 1996 Lexus LS 400

1 Answer

Un work of the doors auto control lexus


1. sitting in driver seat, with driver's door OPEN, press lock/unlock button ON THE DRIVERS DOOR to lock all doors, then manually unlock driver door only.
2. Insert YOUR key in ignition, DO NOT TURN, then remove key.
3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles
4. Shut door.
5. Open door.
6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles
7. With the door open insert your key into the ignition, turn to 'on' position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once by herself). If they don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second, then release the button. The locks should cycle once. If not, start over and go slower.
10. Close the door.
11. Open the door.
12. Press the lock button on the remote. The locks should do a lock-unlock cycle.
13. Close the door
14. Press the lock button on the remote, the doors should lock.
15. Press unlock button and the doors should unlock.

Long beep to follow if successful.

Jun 16, 2009 | 1996 Lexus LS 400

1 Answer

Need the steps to programme the remote


Remote Programming Instructions

1. Driver's door OPEN and unlocked, all other doors closed and locked.

2. Insert YOUR key in ignition, DO NOT TURN, remove key.

3. Using the MANUAL lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

4. Shut door.

5. Open door.

6. Using the lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

7. With the door open insert your key into the ignition, turn to on position (DON'T START), wait 5 seconds. Turn off and remove key.

8. Locks should cycle once (Car will lock and then unlock once). If they don't cycle or they cycle more than once, do steps 1-7 over.

9. Now using the remote, push lock button, hold for one second,
release. The locks should cycle once. If not, start over and go slower.

10. Close the door. Open the door. Press the lock button on the remote. The locks should cycle. Close the door. Press the lock button on the remote, the doors should lock. Press again and the doors should unlock.

Jun 02, 2009 | 1995 Lexus LS 400

1 Answer

Programming keyless remote


2003-04 Mazda 6 REMOTE PROGRAMMING


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

Good Luck.

Jul 12, 2008 | 2003 Mazda Mazda6

Not finding what you are looking for?
2002 Dodge Durango Logo

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...