Question about 1988 Ford Ranger

Open Question

Heater does not work 2009 ford ranger - 1988 Ford Ranger

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 69 Answers

SOURCE: Replace heater core in 1988 Ford Ranger

allow the system to cool down

take radiator cap loose to release pressure

once pressure is released tighten cap

loosen clamps on the heater hoses in the engine compartment on the pass. side of firewall.

plug or cap off the heater core tubes to prevent spillage when you pull it into the truck

place a trash bag on floorboard in case spillage occurs

remove the five screws holding the heatre core access cover, three on top and two on bottom

carefully pull heater core back and down and remove it from the dash

install is reverse

Hope this helps

Posted on Mar 29, 2009

Ad
michigan man
  • 3533 Answers

SOURCE: I want to locate heater component Ford Ranger 1998

try this website to see if they have your car listed it www.autozone.com and if all fail stop by you local library and get your hands on a Haynes auto repair manual for your car they are great i have one for every Ford i own.

Posted on May 30, 2009

  • 7353 Answers

SOURCE: easy way to replace heater core on an 98 ford ranger

the dash must come out.

Posted on Oct 11, 2009

  • 291 Answers

SOURCE: no heat in cab in ford ranger 2005 tied heater

check if both heater hoses going into firewall are hot.. if only one is hot then your heater core is stopped up..you can take both lines loose and take a water hose and back flush,,, force hose on one inlet of heater core for a minute and then the other.. keep going to you get a good flow...make sure heater valve is open, not just valve position take loose and confirm clear..last make sure your thermostat is not stuck open keeping engine from comming up to temperature

Posted on Jan 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Does a2009 Ford Ranger have wheel bearing adjustments?


yes you sure did could have done it yourself the hardest part is taking the tire off.

Aug 25, 2016 | 2009 Ford Ranger Regular

1 Answer

Where is the in line fuseable link located on a 94 ford ranger 2.3 motor


    Alternator fuse link repaired my way. - YouTube

    ? 2:10
    https://www.youtube.com/watch?v=xgJQXKESDcI
    Dec 24, 2013 - Uploaded by Potskie
    I had the exact same situation with my ranger. ... I found thefuse links for the charge or alt output but not the one I ..... In line fuse, battery, or alternator? ... Of Key-Off Battery Drain (Parasitic Draw) - Duration: 18:14. by Motor Age.Missing: 2.3

    Fusible links and inline fuses? - Ford Truck Enthusiasts Forums

    www.ford-trucks.com/forums/885708-fusible-links-and-inline-fuses.html
    Sep 17, 2009 - Location: Kuna ID ... The PO had replaced one of the fusible links with an inline 30amp fuse. .... 81-F-150-Explorer is a splendid one to behold .... to charge the battery goes through that link when needed, and/or the battery to the other components when the engine is off. ... 91 ford ranger 2.3 daily driver 1994 Ford Ranger XLT 2.3L man. trans. - Ford Truck ...
    Jul 6, 2014
    86' Ranger cutting out!!! Fuel ? - Ford Truck Enthusiasts Forums
    May 10, 2012
    90' 302 fusible link for fuel? - Ford Truck Enthusiasts Forums
    Nov 2, 2010
    1988 ranger headlights won't work??? help - Ford Truck ...
    May 17, 2009
    More results from www.ford-trucks.com
    Missing: 94 images for Where is the in line fusible link located on a ...

Dec 30, 2015 | Ford Cars & Trucks

1 Answer

Flush heater core on 2009 ford ranger


if your just doing the heater core you can clamp off the heater hoses to the core, disconnect them from the heater core and run water through it both ways. if its real bad connect spare hoses to the heater core spigots and pour CLR into the core until it is full(coming out other hose) block off hose so the core is filled and let sit. then flush out again until water runs clear. if this won`t clear it then it will have to be replaced.

Mar 06, 2015 | 2009 Ford Ranger Regular

1 Answer

My 09 rangers heater starts then stops then starts and stops and will not give me a continous blowing, any ides?


Not giving you a "continous blowing" would indicate that you have an electrical problem. More than likely that problem is within the blower motor itself. Possibly the motor windings are overheating and shutting down the motor. Then after the wires cools down enough, it starts again. I would say replace the blower motor.

Nov 06, 2014 | 2009 Ford Ranger Regular

1 Answer

Heater blowing cold air


1. Check coolant level to ensure full, and thus getting to heater core.
2. If that didnt work, With engine hot and running, and heat on in the truck, feel heater core inlet and outlet hoses at the engine compartment firewall to ensure both are hot an thus getting flow. If not the core is clogged or there is a faulty valve in the flow path.
3. If te hoses are hot there is flow thru the core and either your blend door is broken and shut or the blend door motor or circuitry is bad.
4. You tube Ford Ranger blend door for video on how to access behind the glove box. You can fairly easily remove the motor and undoing so check its operation and also the blend door operation.
Likely your motor has gone bad and can be replaced using a low profile socket wrench to remove the 3 Screws holding it in place. I bought a new motor for $40 at One o te auto parts chains locally.
Good luck!

Jan 30, 2014 | 2009 Ford Ranger Regular

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...