Question about Toyota Tacoma

Open Question

Replace license plate rear bumper light assembly

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 196 Answers

SOURCE: light replacement

Just reach behind the bumper and grab the light/electrical harness and twist is either way and then it should pull out put in a new 194 bulb and you are set.

Posted on Jan 08, 2009

  • 19 Answers

SOURCE: Can someone explain how to

under the bumper turn the light socket 1/4 turn and pull out.
bulb should a 194 I think?

Posted on Feb 23, 2009

  • 79 Answers

SOURCE: Rear license plate lights burned out and can't

If i remember correctly the entire rear light assembly must be remove in order to access these bulbs. This is true if the license plate is on the trunk. If this is the case then there are nuts on the inside of the trunk that must be removed.

Posted on Aug 14, 2009

c17hydro
  • 2984 Answers

SOURCE: need to replace license plate lights on 95 ford

  1. From underneath the rear of the vehicle, grasp the lamp socket and rotate it 1/4 turn.
  2. Pull the lamp socket from the lens.
  3. Pull the bulb from the socket
  4. Installation is the reverse of the removal procedure.

3761db9.gif
Exploded view of the rear license plate light assembly-step bumper shown, other styles are similar

Posted on Oct 20, 2009

  • 242 Answers

SOURCE: 2010 Honda Odyssey rear bumper was slightly

yes grind back fibreglass the fill ,smooth down repair and prime and paint

Posted on Dec 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 cadillac srx fixing or replacing light bulbs rear license plate


You might be able to access it if you stick your hand up inside the rear of the bumper.

Nov 26, 2015 | 2008 Cadillac Srx

1 Answer

Replace license plate light


With step bumper,
  1. Release the lamp's retainer from the rear bumper by pulling the lamp up and tilting the bottom of the lamp away from the bumper.
  2. Remove the lamp from the rear bumper by rotating it clockwise or counterclockwise

Oct 23, 2013 | 2001 Chevrolet Blazer

1 Answer

Replace license plate light


what country? ( export below means , NOT USA)
its in the FSM
quote:
A single standard equipment rear license plate lamp unit is integral to the
license plate mounting bracket just below the left rear lamp unit on vehicles manufactured for domestic
markets. A bracket with two rear license plate lamps is located on the rear bumper directly below the
spare tire on vehicles manufactured for export markets.
and HOW TO: quote
1. Disconnect and isolate the battery negative cable.
2. Remove the license plate from the rear license plate bracket.
3. Remove the four screws (4) that secure the rear license plate bracket and lamp unit (3) to the four spring
nuts (2) in the rear body sheet metal (5).
4. Pull the bracket and lamp unit away from the rear body sheet metal far enough to access and disconnect
the body wire harness connector (1) from the connector on the back of the bracket and lamp unit housing.
5. Remove the bracket and lamp unit from the vehicle.
unquote the FSM.
Buy one for $20-

Aug 19, 2013 | 2010 Jeep Wrangler

1 Answer

How do I replace a rear license plate bulb in 2004 Jeep Liberty?


  1. Remove the screws that secure the license plate lamp assembly to the rear bumper fascia
  2. Pull the license plate lamp assembly down and out through the mounting hole in the rear bumper fascia far enough to access and disconnect the wire harness connector.
  3. Remove the license plate lamp assembly from the rear bumper fascia.

Apr 16, 2011 | 2004 Jeep Liberty

1 Answer

Tag light is not working. is there a fuse that will get the light turned back on?


The fuse labeled REAR PARK LP 15A in the right instrument panel fuse box powers the rear park lamps, and the tag lamps. If your rear park lamps are working then you most likely need to replace the tag lamps (bulbs). Use the following procedure to replace the lamps.

To Remove:
  1. Remove the two mounting screws from the license plate lamp.
  2. Remove the license plate lamp from the rear bumper fascia.
  3. Remove the license plate lamp socket by turning it counterclockwise.
To Install:
  1. Install the license plate lamp socket by turning it clockwise.
  2. Position the license plate lamp to the rear bumper fascia.
  3. Install the license plate lamp mounting screws.

Feb 17, 2011 | 2004 Chevrolet Impala

1 Answer

Do I have to remove the tray liner from the 2003 Rodeo pick up to replace tail light assembly?


Utility And Sportside Pick-Up Models
  1. Make sure the headlight switch is off and the ignition switch is in the lock position.

  2. Unfasten the screws retaining the lens, then remove the lens.

  3. Disconnect the bulb socket from the license plate lamp by rotating it 1/4 of a turn counterclockwise.

  4. Remove the bulb from the socket.

  5. Installation is the reverse of removal.
    Without A Step Bumper

    1. Make sure the headlight switch is off and the ignition switch is in the lock position.

    2. Disconnect the bulb socket from the license plate lamp by rotating it 1/4 of a turn counterclockwise.

    3. Pull the bulb from the socket.

    4. If necessary, remove the lens retaining clip and the lens from the filler panel.

    5. Installation is the reverse of removal.
      With A Step Bumper

      1. Make sure the headlight switch is off and the ignition switch is in the lock position.

      2. If necessary, lift the lamp up and tilt the bottom away from the bumper to release the lamp retainer.

      3. Disconnect the bulb socket from the license plate lamp by rotating it 1/4 of a turn counterclockwise.

      4. Pull the bulb from the socket.

      5. If necessary, remove the step bumper pad, the screws that attach the lamp to the bumper and remove the lamp assembly.

      6. Installation is the reverse of removal. Tighten the lamp assembly-to-bumper screws to 14 inch lbs. (1.6 Nm).

Dec 12, 2010 | Isuzu Pickup Cars & Trucks

1 Answer

Accessing the rear hatch brake light on a 1999 Ford Expedition


There should be 2 screws holding the lenses on for the hatch light, remove those and cover comes off. The plate lights, access them under the rear bumper, they twist and pull out, then just pull the bulb out the connector. The running board light, under board, which will take the light assembly out, or a small flat head screwdriver, pop the lens off the top of board.

Dec 27, 2009 | 1999 Ford Expedition

1 Answer

Need to replace license plate lights on 95 ford explorer. can't reach underneath the bumper. does the plastic assembly just twist off?


  1. From underneath the rear of the vehicle, grasp the lamp socket and rotate it 1/4 turn.
  2. Pull the lamp socket from the lens.
  3. Pull the bulb from the socket
  4. Installation is the reverse of the removal procedure.

3761db9.gif
Exploded view of the rear license plate light assembly-step bumper shown, other styles are similar

Oct 20, 2009 | 1995 Ford Explorer

1 Answer

1999 Dodge Neon rear license Plate bulb


LICENSE PLATE LAMP BULB
REMOVAL
  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Oct 08, 2009 | 1999 Dodge Neon

1 Answer

Need to change rear bumper license plate bulbs in a 1991 F-250


push the light from inside your bumper to the outside. May have to tap with a hammer or wrench. New light will push in from the outside toward the inside. Reconnect the wire and you should be up and running!

Jun 11, 2009 | 1991 Ford F250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...