Reprogram remote entry - 2007 Infiniti G35 Sedan Sport Sedan

Hello Cathy

It does indeed have keyless entry. It needs reprogramming when you get a new remote. Also if you disconnect the battery. Usually a local car alarm fitting shop, or an auto-electrician will do it. Plus of course a Ford dealership.

https://www.google.com/search?q=Keyless+Entry+Remote+System+1999+Ford+Windstar

..

Remote Transmitter Programming NOTE: All keyless entry remote transmitters must be programmed at the same time.
NOTE: Programming (or reprogramming) the keyless entry remote transmitters into the central security module can be accomplished using a diagnostic tool or by carrying out the following steps.

1. Turn the ignition switch from OFF to RUN eight times within 10 seconds, ending in RUN. If the module has successfully entered program mode, it will lock and then unlock all doors.

1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.

1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.

1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after Step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the doors will lock and unlock one last time to confirm.

the operators guide covers this.
lost that? (in the glove box is was)

You did it like this ?
Programming -Keyless Entry Remote Transmitter NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), perform the following steps.

1. Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.

1. NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met. Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.

1. If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.

1. Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.

Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:

1. Make sure that the anti-theft system is not armed or triggered.

1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.

1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.

1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.

1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.

• To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:

1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
   

1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
   

1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
   

1. Turn ignition switch OFF. All doors should lock and then unlock.
   

1. Check operation.
   

if its factory keyless entry, chances are your battery for your remote need to be replaced, the remote could also need to be reprogrammed... If it is an after-market system, there are several possibilities... wires could be pinched, the door lock solenoids could be broken or misaligned, the "brain" of the system might need to be reprogrammed.

Hello
this is how to program the remotes/keyless entry

How

• Obtain all remote transmitters
• enter the 5 digit permanent code into the keyless entry pad on the drivers door
• Press the 1-2 switch on the keyless entry pad
• Within 5 seconds
• Press any button on the first remote transmitter
• The doors should open then lock
• Within 5 seconds
• press any button on the second & third remote
• within 5 seconds for each remote
• to exit programming
• simultanionusly press 7-8 & 9-0 switchs on the key pad or wait more then 7.5 seconds

NOTE
The 5 digit permanent code is located in one of the following places

1. On the owners warranty card
2. On the label on the inside the trunk/ boot
3. On the owners code card
4. On the centrel locking control module located in the drivers door
5. In the PCM ford can get this for about $25.00

I hope this help
Regards Paul
www.limotec.co.uk

need to remove door panel either the linkage clip either broke or disconnected --if have remote start on fob need dealer to program--if normal try these links
Lexus Free Keyless Remote Fob Entry programming instructions Free Keyless Remote Fob Entry programming instructions procedures for all...

I had the same problem. Went to dealer who said it probably needed to be reprogrammed (around $45-50). Paid for premium assistance with FixYA. Ginko gave me the procedure to reprogram my remotes. It was very easy and worked great. Now both of my remotes are working and it only cost me $9.99.

JOECOV