Question about 1989 Ford Aerostar Cargo

Open Question

89 Aerostar, we need a belt diagram

I have an 89 Aerostar that we took the belts off of and can't remember how they go back on. Does anyone have a diagram? It's a 6 cyl.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Saaboheme
  • 76 Answers

SOURCE: 1993 saab 900 belt diagram

Sorry, I don't have access to a Bentley now. There are 4 belts, 2 for alternator etc, 1 for aircon and 1 for pwr steering.
The power steering belt goes round the power steering pump & crank pulley only.
The paired belts go round crank pulley, alternator and water pump.
The aircon belt goes round crank pulley, aircon compressor and tensioner.
Alternator / water pump pair are closest to the engine.
Power steering is in the middle (with aircon) or closest to the bulkhead (without aircon).
Aircon (if fitted) is closest to the bulkhead.

(1) If you do not have an AC compressor, skip this step and go to step 2. If you dohave one, begin by cutting any cable ties that hold the main wiringharness to the AC hoses. Lift the harness up and over onto the camcover until it's near the PCV valve, and is now out of your way.

All nuts & bolts in this step are 13 mm.

Then, slacken the 2 bolts attaching the AC tensioner pulley mount (athick triangular steel plate) to the head. Use a long box wrench (ringspanner, in Englishicon_cheesygrin.gif ).

Using a deep-wall socket (or an offset ratchet wrench, or plain wrench)on the adjuster nut, back it off until there's no more tension in thebelt (you won't be able to remove the belt yet, though).

Now, remove the upper of the 2 mounting bolts and its washer, and pivot the tensioner down; remove the belt.

Remove the lower bolt, and lift out the tensioner. Look the triangularplate over for cracks, and spin the pulley to see if its bearing issmooth and quiet. (If you find problems, the pulley is about $15 and www.eeuroparts.com sells the entiretensioner assembly for something like $70.) Back off the adjuster nutuntil it's about 1/4" (1/2 cm) from the end of its threaded rod (usevise-grips to clamp the rod's other end onto the triangular plate, orput the whole thing in a vise).

(2) Slacken the bolt and nut holding the power steering pump to thehead and to the RH engine mount, respectively. Slacken the adjuster nut(yes, anotherthreaded-rod type thing) by about 1/2" (1 cm). You can use a normalwrench for this, but it takes forever--so I made a special tool bytaking a cheapo 13 mm open-jaw wrench and bending it to a 45-degreeangle just below the jaws (cut it to length if it's too hard tomaneuver). Loosen the mounting nut until it's almost off (but not completely off,or you'll lose the bolt it screws onto--this bolt was designed to fallout when the nut is removed). Pull the nut end of the threaded rodtowards the firewall to get it of the adjuster fork. Push the pumptowards the engine centerline and pull its belt off (you may need topry with a screwdriver to get it out of the pump pulley completely).

(3) Slacken the 16 mm nut on top of the alternator. Back off the alt.adjuster's 10 mm nut about 1/2" (1 cm)--a ratcheting wrench helps here.(This is the last threaded rod--I promise.) Completely remove the 16 mmnut, and pull the adjuster towards the firewall until it's out of thealt.

Now for the clever part: Cut yourself a wedge from a piece of wood (2 x4 is perfect), with a rise of 3" (8 cm) and a run of about 12" (30 cm).Push the alt. towards the engine, and shove the wedge in between theside of the alt. and the coil-spring tower (master cylinder mountingbracket works, too). Keep pushing the alt. and driving the wedge downuntil the alt. is so close to the engine that it's compressing thelower heater hose.

Pull the outer belt off the alt. pulley. Working from the RH side ofthe car, lift the belt off the water pump pulley and then disengage itfrom the crank pulley. Now, pull the inner belt into the outergroove of the water pump pulley. Go back to the LH side of the car, andmove the inner belt into the alt. pulley's outer groove. Try removingit from this pulley; if too difficult, either wedge the alt. closer tothe engine or try pulling the belt off the water pump pulley from theRH side of the car (a helper is very useful for all this).

(4) Install the new inner belt by fitting it into its groove in thecrank pulley first. Work it into the outer grooves of the alt. andwater pump pulleys, then into the inner ones. Install the outerbelt--again, first onto the crank pulley, then the water pump and alt.pulleys.

Remove wedge. Insert tensioner into alt. making sure the threaded rodsettles into its fork, and refit its 16 mm nut--but don't fully tightenit yet. Tighten 10 mm adjuster nut until belts can be pushed in only1/2" (1 cm) by thumb pressure (applied 1/2 way between water pump andcrank pulleys).

(5) Push PS pump as close to engine centerline as possible, andfinger-tighten its mounting bolt to hold it there. Fit a new beltaround the crank pulley first, then work it into the pump pulley groovefrom the bottom of the pulley until it pops in. You may need to use both hands, and/or carefully pry the belt on with a screwdriver.

Loosen the bolt you just tightened. Pull the pump away from enginecenterline, insert threaded rod into its fork (you may have to back theadjuster nut off some more), tighten the mounting nut (but notcompletely), and screw in the adjuster nut until the belt deflects asdescribed in (4) above.

(6) Start the engine. Blip throttle, watching the belts deflect as theengine speed goes up and down. If the "blur" you see midway down eachbelt is over 1" (2 cm) wide, tighten the belt(s) until it isn't. Tighten the PS pump mounting nut and bolt, and the 16mm nut on the alt.

If your car doesn't have AC, your belt replacement is over!

(7) If you haveAC, reattach the tensioner to the head with the lower bolt only (andleave this bolt finger-tight). Fit the new belt around the crankpulley, then around the compressor pulley and, finally, around thetensioner.

Reinstall the top tensioner bolt and its washer. Be careful and patienthere--you're threading a steel bolt into aluminum, so make sure it goesin straight. You may have to back off the tensioner nut a little. Leavethis bolt finger-tight.

Screw in the adjuster nut to get the deflection as described in (4)above. Start the engine, and blip the throttle. Watch belt's "blur" on LHside of engine. Adjust as in (6). Switch on compressor, and repeat.

If satisfied, tighten the 2 tensioner bolts. Return wiring harness toits original position, and re-secure with cable ties if needed.

Posted on Dec 16, 2008

Ad
bschilz
  • 2049 Answers

SOURCE: serpentine belt diagram mazda 6 2005

Here are links to the diagram...

If your engine is the 2.3L 4 cyl... http://www.gates.com/common/part_locator/view_diagram.cfm?id=S7042

If your engine is the 3.0L V6... http://www.gates.com/common/part_locator/view_diagram.cfm?id=S6036

Posted on Sep 01, 2009

ZJLimited
  • 17970 Answers

SOURCE: I need a diagram of a serpentine belt

I hope help you with this;

1993 CHEVROLET BLAZER - V8 5.7L 350ci GAS FI N K
Belt Routing Diagram - Part Number 5060940 / Multiple Accessory, w/o 120 Amp Alt., w/o A.P., w/o A.C.
ea04cea.jpg


Belt Routing Diagram - Part Number 5060955 / Multiple Accessory, w/o 120 Amp Alt., w/o A.P., w/A.C.
4470fe3.jpg


Belt Routing Diagram - Part Number 5060968 / Multiple Accessory, w/120 Amp Alt., w/A.P., w/o A.C.
658715c.jpg

Belt Routing Diagram - Part Number 5060970 / Multiple Accessory, w/o 120 Amp Alt., w/A.P., w/A.C.
a37b28a.jpg


For more details, I suggest visit DAYCO Catalog

Good luck (remember rated this help).

Posted on Sep 30, 2009

Testimonial: "Thank you"

bschilz
  • 2049 Answers

SOURCE: I need the diagram for serpentine belt routing on

Here's the diagram you asked for...

85cf64b.jpg

Posted on Jan 25, 2010

motor1258
  • 6674 Answers

SOURCE: Belt Routing Diagram 1991 Ford Truck F150 1/2 ton

this should be it.a7f9a2b.gif

Posted on Feb 20, 2010

Testimonial: "quick responce"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 ford aerostar 4.0L 6 cyl diagram for drivetrain belt


https://www.2carpros.com/questions/ford-aerostar-1994-ford-aerostar-belt-diagram

Oct 09, 2018 | Ford Cars & Trucks

1 Answer

Need serpentine belt diagrams for 1996 ford Aerostar minivan. Need diagram of both belts


if you haven`t started the job and the belts are still on then all you have to do is draw how each belt is routed on the pullies then replace them.if the belts are not on then you can see if the parts supplier or the dealer can show you a diagram.there is a sticker on the upper rad support that shows how the belts are routed but at the age of this car it is probably missing.you can also go to the library and look at the books they have it should show how the belts are routed.

Mar 24, 2011 | 1996 Ford Aerostar Extended

1 Answer

I need a diagram for the serpentine belt for a 2.8L engine in a 89 S10. Searching this site I see that some genius said that you should "look under the hood". I looked - no help. I NEED A...


Depending on how your vehicle is equipped will determine the belt routing, see attached.

No power steering or AC
91stt_5.jpg

With power steering
91stt_6.jpg

With power steering and AC
91stt_7.jpg

Nov 12, 2010 | 1987 Chevrolet S-10 Pickup

1 Answer

Belt won't tighten


did you look on the underside of the hood,or the radiator shroud? Generally a diagram showing the routing system is there. if not,then autozone and oreilly autoparts can print you one for free. there are some on the net...but i would be leary unless edmunds.com has one you can take a peek at. too many websites offer the wrong things when it comes to working on vehicles.

May 01, 2010 | 1990 Ford Aerostar

1 Answer

Diagram for putting on altenator belt for 92 ford aerostar van


Click on the following direct Link. It has the Serpentine Belt Diagrams that you will need for your specific engine size and options (AC/No AC etc.).

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/1992/make/ford/model/aerostar/1992_ford_aerostar_drive_belt_routing_diagram.htm

Mar 22, 2010 | 1992 Ford Aerostar Extended

1 Answer

Free photo diagram of belt routing


Hope you did the timing belt too, or back up and cover that now.
I believe it goes
Inner belt, crank, alternator, water pump, crank
Outer belt, Crank. a/c, tensioner (backside), Crank

Jan 24, 2010 | 1995 Geo Metro

1 Answer

I need a belt diagram for a 1991 ford aerostar with 3.0 with ac


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/1991/make/ford/model/aerostar/1991_ford_aerostar_drive_belt_routing_diagram.htm

Nov 14, 2009 | 1991 Ford Aerostar Extended

1 Answer

Fan belt diagharm for 3.0 ford


Here is a serpentine belt diagram for you vehicle. This is for a 1995 Ford Aerostar with a 3.0 liter engine. Have a great day and i hope this helps!!b220738.gif

Oct 04, 2009 | 1995 Ford Aerostar

2 Answers

Alternator Belt routing


hey tony , i tried to highlight for the distinction between the 2 belts , red for alt , and blue for p/s . hope you can follow my drawing .

bdabd04.jpg

J5

Jan 20, 2009 | 1992 Ford Aerostar Extended

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

233 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

83959 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22441 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...