How to replace front door handle on a 2001 toyota sienna van

Get a replacement handle REmove door trim to get to the retaining bolts holding the old door handle in place. Replace and reassemble in reverse

Remove the internal handle and I think 1 or 2 screws and lift inside door panel off, pull the latch and it will open!!

The door handle might be broken, you need a new part. I got mine online for $40. keywords: 2001 2002 2003 2004 2005 2006 2007 Toyota Sequoia Metal Lift Gate Exterior Door Handle for Rear Outside Van Tailgate Handle. You need to remove the back door panel to replace this.

the inside door panel. you need to removethe assist grip and door pull ******** the lift gatetrim panel (you'll need a 10mm socket)use a flat screw driver to carefully pray all around the the panel and then pull it off. you should be able to see the handle and youll know what to do depending if you are replacing just the handle or the whole latch. good luck

If you can remove the inner door panel you will see a maze of cables running to the various locking points on the sliding door. If the cable going to the FRONT latch on the sliding door is broken (or in my case, simply dislodged inside the door) the door acts as if it is frozen shut.

The front cable is short, and easily replaced even by a newbie mechanic.

The first thing to check is the fuse that controls that door's motor. Look in your manual for the fuse chart. Determine where the fuse panel is and which fuse it is. Pull that fuse and take a close look to see if it has blown. If so, replace it with a new one of the same amperage

The handle that broke had a little 'finger' that actuated the release mechanism. The only way to open the back hatch is to remove the inner panel and push on the release mechanism.

Once off, you can either a) buy a replacement handle (expensive) or b) do what I did and simply make a piece of L-shaped metal to lever the release mechanism from the outside.

If your handle is completely off of the door you can look up under the little plastic cover (that hides the handle) and see the slot on the right side that the release handle inserts into. You need to stick the lever into that slot, and angle it down about 30 degrees from horizontal to get under the latch mechanism, which unlocks the hatch if you pry it upwards.

I replaced both of my sliding door handles this weekend. It was actually pretty easy. Cheapest I could find the handles was a little over $70 each. The interior panel is held on with one screw and 10 nylon clips. The one screw is in the cup holder. Put you hand in the cup holder and push out at the bottom. It pops right off exposing the one screw. I started on the clips from the top at a corner. Seemed to be the easiest place to slide a screw driver under. Once I got the screw driver in, I started working my fingers under the panel. The clips run mostly along the top and bottom about 6 inches from the edge. I made an effort to apply the force as close to the clips as I could to reduce flexing the panel. Once I got the first clip to pop out the other followed pretty easy and the panel lifted right off. Carefully peel back the plastic barrier. The exterior handle is held on with two 10mm bolts. Connecting the short cable was pretty obvious once you could see everything. Now I have to teach everyone to open the side doors very gently! Hope this helps.

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

I hope I can help, I had the same problem on my 2001. I called the dealership and they said 375.00 + parts to fix. Being mechanically inclined I decidet to try it myself. Please understand, this is not exact, but is a pretty good guide. To open from the outside, make sure doors are unlocked(mine relocked after a minute or so) place a screwdriver, long and thin, into the slot that the handle passes through the door on the right side. Raise the handle of the driver, and you should be pressing down on a cable that operates the latch. the door should release. If you cant do that, from the inside, remove the two side trim pieces. Then remove the inner door panel, One screw under plastic cap on handle, one under cap on strap... and pop off all plastic buttons(hidden) between the door and cover, a 1" putty knife will work for this. You will see the cable that used to connect to the handle. Remove the cable by pulling it through the slot(apparent when you get to it) and now remove the two screws that hold the handle on. Also, you have to remove a screw from the passengers side of the cover plate over the handle. the plate will slide(not sure which way now), and it will come off. replace the handle and etc..... inreverse.. Took me 25 minutes, start to finish. Further questions, let me know. remember, mine was 2001 Sienna.