Check to make sure the motors are moving hot to cold. The blinking control panel means it has self diag mode. Google how to get the heater control panel to go into self diag mode and when you get codes goggle them too . Prob bad control panel switch or unit
SOURCE: 2000 GMC Sierra 5.3 Litre, won't blow hot air
I experienced the same head ache. First attempt was to replace the thrmostat and after taking it apart I realized that there was nothing wrong with it. I then removed the plastic cover/panel located under the dash board on the passenger's side. (only a few 4-5 smalls screws) Removal will enable you to see the on/off switch/gate moving/rotating as you turn the knob to hot or cold positions, on the control panel. If that switch/gate seems to work ok, then the trouble is within the heater core. Many mechanincs suggested that I replace the heater core. A very expensive proposition.
I checked the heater core supply/intake hose and found it hot to the touch, while the return hose was nearly cold. It was definitely a heater core blockage. I removed both ends (supply and return) hose connections/clamps. They are located near the fire wall in the engine compartment. A special tool is very helpful to remove those clamps easily and to replace them as well. It can be done the old fashion way but this tool was a life saver and reduced work time to just minutes. (Tool is $70.00 bucks at auto parts store,so I borrowed mine from a mechanic/friend)
I then hooked up a garden hose to the return end of the heater core and reversed the flow of coolant/water through the heater core. My truck is a Sierra 2000 and I refuse to see how a heater core could get clogged up with clear coolant alone. To my surprise a flat piece of rubber about the size of a quarter blew out of it and the flow of water became unobstructed. I reconected the ends of the hoses to the heater core, replaced the lost antifreeze & everything returned back to normal. No money spent for something most mechanics suggested I replace control valves/switches ($280.00) replace heater core ($500.00) etc etc. I am glad I was curageous enough to tackle this myself and save a few pennies. Good luck, and I hope this will work for you.
SOURCE: 93 gmc sierra heater not working
THERMOSTAT REPLACE IF NOT SEE IF HOSES ARE CLOGGED SHOT OF AIR COULD HELP OR DISSCONNECT BATTERY CABLE 10-15 MIN CONNECT BACK TRY HEATER
SOURCE: my air blows hot even tho my climate control is on cold
U have a stuck air temp control blend door, either the actuator motor is defective or the door is warped and has jammed, one thing is that u must remove the dash to rcheck replace these parts.
Air
Temperature Control Blend Door Failure No Heat or no AC (dependes on
where door sticks)
In
all modern cars there is a tiny DC electric motor driven gear drive
that moves a plastic door that blends heated and cooled air from the
AC and the heater core, this is called (interestedly enough) the air
temperature control blend door actuator. The motor that moves this
door fails because the door starts sticking from warping, most common
complaint is no heat but it can be no AC as well. To replace these
parts (blend door and blend door actuator) you must remove the entire
dash from the car. Always have this problem confirmed by a dealer or
qualified repair shop as it is a very expensive repair.
Other causes of no heat in the cabin are engine thermostats that are stuck open (engine runs cold) or air bubbles in the cooling system.
259 views
Usually answered in minutes!
k so to let people know on my problem i got it fixed and the deal is when you go buy new blend air motors from your automotive store make sure they are the right ones because the ones they have are universal ones how ever does not work for my truck because the right one has some kind of sensor that tells it where the door is at and you put that universal one in their it does not communicate with the control panel and makes it have an error and thats where the blinking comes in and also my heater resistor was out so thank you to the people that helped me out
×