Question about Mercury Grand Marquis

Open Question

Parts and labor costs to replace pinion seal on 2000 Mercury Grand Marquis

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 92 Answers

SOURCE: pinion seal leaking

check your rear diff vent if pluged clean it out and clean up the pinion seal.sometimes if the leak is caused by pluged vent and has not been leaking long once vent is clean sometimes the leak will stop.there is not a specific torque amount because it is rotational torque(how hard to turn pinion).there is a crush sleve on the pinion and if torqued too tight or too loose brg preload will be wrong and brg damage could result.mark and remove drive shaft.remove rear wheels,brakes,axles.so when turning pinion you dont have any drag from brakes or axles.mark the position of the yoke on the pinion.remove yoke,replace seal,reinstall yoke be sure to replace pinion nut.tighten nut until it takes the exact same amount of force to turn pinion as before taking original pinion nut off.hope this helps.

Posted on Oct 22, 2008

  • 87 Answers

SOURCE: rear shocks on a 1996 Mercury Grand Marquis

2 bolts on the top of shocks and 1 bolt on the bottom but the top 2 bolts are a pain in the neck

Posted on Mar 10, 2009

  • 157 Answers

SOURCE: labor for rear main seal and serpentine belt replacement

4 hours

Posted on Dec 01, 2009

  • 58 Answers

SOURCE: where are the spark plugs located on a 2000 Mercury Grand Marquis

There are eight COPs (coil-on-plugs) to remove. Using a 7mm or 9/32" socket, remove each bolt securing each COP to the intake manifold on top of the engine. Remove all eight COPs, and the spark plugs are underneath. When replacing the spark plugs, use only the proper Ford/Motorcraft plugs, even if they cost twice as much as the aftermarket ones. You will avoid further headaches this way. Hope this helps.

Posted on Mar 30, 2010

  • 564 Answers

SOURCE: how to replace starter +1993 Mercury Grand Marquis

disconnect battery,,jack car up,,put jack stand on frame,,take starter bolts out,(may not be easy),,take wires off starter,,hoped it helped,,

Posted on May 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much does it cost fix rear differential pinion seal leak on 2000 mercury mountaineer


You would have to ask any cost questions ,on any vehicle
repairs,to the merchant or shop of your choice

There is no set price

Every shop has different labor rates & skill
set levels.

Jul 31, 2011 | 2000 Mercury Mountaineer

1 Answer

I have what appears to be a broken 9L3Z8592B (thermostat housing) from a 2000 Grand Marquis. How big a deal is that to replace? The part's cheap enough...


its not hard to replace and while your there change the thermostat and gasket(seal) and the anti-freeze if it hasn`t been changed.make sure all the air is out of the system after refilling.

Apr 24, 2011 | 2000 Mercury Grand Marquis

2 Answers

Cylynder head needs to be replaced. what will it cost. it has a 302 5.0


about $800-$1000 for one cylinder head parts and labor, but it is recommened always that both be replaced or rebuilt.

May 27, 2010 | 1986 Mercury Grand Marquis

1 Answer

1997 Grand Marquis-Montigua--What would be the rough cost to replace the "intake" (incl. labor)?


The intake manifold with gaskets runs about $250.00, then probably $100-$200 for labor, about 2-4 hours of time.

May 26, 2010 | 1997 Mercury Grand Marquis

1 Answer

Cost and labor new fuel pump for 01 grand marquis


$100-200 for the pump, $100-250 for labor.

May 21, 2010 | 2001 Mercury Grand Marquis

2 Answers

Where are the spark plugs located on a 2000 Mercury grand Marquis?


There are eight COPs (coil-on-plugs) to remove. Using a 7mm or 9/32" socket, remove each bolt securing each COP to the intake manifold on top of the engine. Remove all eight COPs, and the spark plugs are underneath. When replacing the spark plugs, use only the proper Ford/Motorcraft plugs, even if they cost twice as much as the aftermarket ones. You will avoid further headaches this way. Hope this helps.

Mar 30, 2010 | 2000 Mercury Grand Marquis

1 Answer

What is the labor time to replace valve cover gaskets on a 2003 mercury grand marquis?


I'm not sure what the labor time is but technically it doesnt take ALL that long. Besides removing a few parts to clear a way to the covers. I would assume somewhere around 3-5 hours is what you might get hit up for.

Jan 05, 2010 | 2003 Mercury Grand Marquis

1 Answer

What is the average cost of replacing the timing belt in a 2005 grand marquis?


the book time is 7.8 hours timeswhat your shop gets per hour also this is labor only you have to add parts

Nov 09, 2009 | 2005 Mercury Grand Marquis

1 Answer

Cost to replace and repair heater core in 99 Grand Marquis


about $1200 US, this requires the dash be pulled out, about 12 hours of labor.

Mar 24, 2009 | 1999 Mercury Grand Marquis

1 Answer

2000 Mercury Grand Marquis


I was given an solution by emissionwiz from the fixya site.

Thanks,
GGBMDB

Nov 30, 2008 | 2000 Mercury Grand Marquis

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...