Question about 2007 Chevrolet Captiva 2.0

Open Question

Hello...might diagnostics show codes c0561 and P0300 on a 2007 Suburban. Any clue

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 GMC Sierra traction control light on


traction control light on . DTC'S - diagnostic trouble codes are stored in ABS control module pointing to the malfunction . Take to a qualified repair shop or to auto part store that can pull these code. DTC C0242 00: Engine Control Module (ECM) Indicated TCS Malfunction
DTC P0856: Traction Control Torque Request Circuit
The electronic brake control module (EBCM) and the engine control module (ECM) simultaneously control the traction control. The EBCM sends a serial data message to the ECM requesting torque reduction. When certain ECM DTCs are set, the ECM will not be able to perform the torque reduction for traction control. A serial data message is sent to the EBCM indicating that traction control is not allowed.
DTC C0561 4B: System Disabled Information Stored Calibration Not Learned
DTC C0561 54: System Disabled Information Stored Temparature High
DTC C0561 59: System Disabled Information Stored Component Protection Time Out
DTC C0561 71: System Disabled Information Stored Invalid Serial Data Received
DTC C0561 72: System Disabled Information Stored Alive Counter Incorrect
DTC C0561 74: System Disabled Information Stored Value of Signal Protection Calculation Incorrect
DTC C0561 75: System Disabled Information Stored Signal Above Allowable Range

Traction Control Off Indicator
The IPC illuminates the traction off indicator when the following occurs.
• The EBCM disables engine torque reduction due to a malfunction and sends a serial data message to the IPC requesting illumination.
• The driver manually disables VSES and engine torque reduction by pressing the traction control switch. The EBCM sends a serial data message to the IPC requesting illumination.

Sep 04, 2017 | GMC Cars & Trucks

1 Answer

Code C0561 for a chevy malibu


co561 System Voltage unstable,, po751 Shift solenoid A CKT
performance or stuck Off,, po700 Trans Control Sys. Malfunction
these are OBD codes, hope that helps....

Feb 24, 2015 | 2007 Chevrolet Malibu

1 Answer

GMC Yukon has code C0561 stability/ traction comes on


Could be bad coils on 3&7,if not can be module,try to swap coils if will show the same number that mean MODULE.

Jan 10, 2015 | 2007 GMC Yukon

1 Answer

Acadia 2009 code C0561 what does it mean?


You won't find this information in a Haynes manual ! I know , I work for a GMC dealership , along with Chevy and Cadillac ! this information I'm adding is right out of GMC service information .
Diagnostic Instructions
?€¢
Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.


?€¢
Review Strategy Based Diagnosis for an overview of the diagnostic approach.


?€¢
Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors
DTC C0561 71: System Disabled Information Stored Invalid Serial Data Received

DTC C0561 72: System Disabled Information Stored Alive Counter Incorrect

DTC C0561 74: System Disabled Information Value of Signal Protection Calculation Incorrect

Circuit/System Description
The electronic brake control module (EBCM) receives serial data messages from the body control module (BCM), engine control module (ECM), instrument panel cluster (IPC), and the transmission control module (TCM) which are needed to perform antilock brake system (ABS), vehicle stability enhancement system (VSES), or traction control system (TCS) functions.
Conditions for Running the DTC
Ignition voltage is greater than 10 volts.
Conditions for Setting the DTC
The EBCM receives an invalid serial data message from another module.
Action Taken When the DTC Sets
?€¢
The EBCM disables the traction control system (TCS)/ vehicle stability enhancement system (VSES).


?€¢
A DIC message and/or a warning indicator may be displayed.

Conditions for Clearing the DTC
?€¢
The condition for the DTC is no longer present.


?€¢
The EBCM clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles.

Diagnostic Aids
This DTC indicates that there are no problems in the EBCM. The BCM, ECM, IPC and the TCM should be checked for a possible fault.
Reference Information
Schematic Reference
Antilock Brake System Schematics
Connector End View Reference Component Connector End Views
Description and Operation ABS Description and Operation
Electrical Information Reference ?€¢
Circuit Testing


?€¢
Connector Repairs


?€¢
Testing for Intermittent Conditions and Poor Connections


?€¢
Wiring Repairs
Scan Tool Reference Control Module References for scan tool information
Circuit/System Verification

  1. With a scan tool, view the Invalid Signal Data Display.
  2. If no invalid signal are present, view Signal Fault Data in the Enhanced DTC Data.
  3. Refer to appropriate module for diagnosing the invalid message data.
  4. Do not replace the EBCM due to this DTC fault.
You would need a factory scan tool or equivalent too diagnose this ,not a code reader . So do your self a favor an take to a dealership. I've been doing this for thirty years .

Sep 26, 2014 | 2007 GMC Acadia SLE

1 Answer

Trouble codes stabilitrack and trackion on dash board


Most likely its the throttle position sensor. Gm is having a fit with them on the 5.3 engines. What your seeing with the stabilitrac/traction control is common. Try this as a test. Take off the negative battery cable for about 2-3 minutes, let the ECM dump its memory, hook it up and try it. If it comes out of limp mode, its probably the sensor. Unfortunately, It likely will go back into limp-home after a short drive. GM has had a "campaign" on those, and was replacing them free for a while. Good Luck !

Feb 16, 2014 | 2007 Chevrolet Chevrolet Suburban 1500 LS

1 Answer

Torrent 2007 code C0561 what it is ?


please read the following answer:

http://www.ricksfreeautorepairadvice.com/repair-topics/computers-sensors/trouble-codes-p0404-p0405-and-c0561-on-2007-pontiac-torrent-with-the-3-4l-engine-check-engine-light-on-traction-control-light-on

Jan 19, 2013 | Cars & Trucks

1 Answer

Solutions for dtc co561


DTC C0561
The electronic brake control module (EBCM) disables the traction control when other electronic control modules set DTCs for components that effect the operation of the traction control system.
DTC C0561 System Disabled Information Stored
Conditions for Setting the DTC
The powertrain control module (PCM) or body control module (BCM) diagnoses a condition preventing the engine control portion of the traction control function and sends a serial data message to the EBCM indicating that torque reduction is not allowed. The PCM or BCM will typically set a DTC and the EBCM will set this DTC.
This vehicle has DTCs which include DTC Symptoms. For more information on DTC Symptoms, refer to DTC Symptom Description .

DTC Symptom

DTC Symptom Descriptor
71
Invalid Serial Data Received
72
Alive Counter Incorrect/Not Updated

Diagnostic Aids
This DTC is for information only. As an aid to the technician, this DTC indicates that there are no problems in the ABS/traction control system (TCS).
© 2015 General Motors Corporation. All rights reserved.
This is something you'll need to take to the dealer !

Oct 23, 2012 | 2006 Chevrolet Impala

1 Answer

C0561


C0561 sets in a module because another module is telling that module to stop operating this system.For instance a check engine light coming on may turn off the traction control system.There fore the traction control module (ebcm may have set a C0561).You need to check other modules for codes.

Aug 17, 2011 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

I have chevy equinox 2007 AWD LT , i sccaned system yesterday i had the Code C0561/71 whats the meaning of this code can someone help.


you can reads a code ?? this is a result as the europeon model of this vehicle which has a OBDII is all encrypted software and iam extremely jealous .Sorry but this code number doesnt show in my list of manufacturers codes or the generic code chart

May 25, 2011 | 2007 Chevrolet Equinox LS New Cars

1 Answer

Has dtc #c0561 and engine code #p0011-breifly explain description


code P0011 intake camshaft position performance ( could be a camshaft sensor, or could be that the intake camshaft variable timing unit is stuck try changing the oil and filter and add some seafome to the oil clear the code and drive it and see if the code comes back)

code C0561 system disabled information stored ( the electronic brake control module disables the traction control system when their is a DTC stored that might effect the traction control system, could be caused by the P0011 )

Apr 19, 2011 | 2006 Chevrolet HHR

Not finding what you are looking for?
2007 Chevrolet Captiva 2.0 Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...