Question about Cars & Trucks

1 Answer

Does a mitsi pajero E-V25W with a 6G74GDI engine use a crank position or crank angle sensor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 42,757 Answers

Check with a service department but I am sure that it will have.

Posted on Oct 23, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 701 Answers

SOURCE: need location of crank angle sensor on 1997 pontiac sunfire 2.2 liter

Hello oldiro: My name is Roger and I can help. From under the vehicle look up between the transmission and the side of the block. Mid motor above the pan rail there is a bolted in sensor. This should be the crank sensor.It will have two wires plugged in to it. Please rate this answer as this lets us know you received the information you asked for. Should you need further help please just ask. Thank You for using FixYa. Roger

Posted on May 06, 2009

localwonder
  • 6784 Answers

SOURCE: crank angle sensor location

The crank sensor is always located next to the crankshaft pulley. it will be inserted into the block with the top part of the housing half way out. you cant miss the wires leading into the tip of the housing next to the crank shaft pulley.

Posted on May 23, 2009

  • 1 Answer

SOURCE: 98 MITSI PAJERO FAULT CODE 78 APS(MAIN)

78 APS (main) what does mean?

Posted on Mar 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mitsi pajero 2.8d 2001 turns over for ages before starting and revs for a while and then sometimes cuts out ?


Sounds like fuel pump seals. Remove your fuel filter and have a look see if its black.
I have one so try looking on pocuk. pajero owners club uk great place for advice as we all have these trucks and need help every once in a while.

Hope this helps.
Also I run my truck with 250ml of two stroke oil in £50 worth of diesel helps the injectors to work better ;-)

Sep 26, 2016 | 2001 Mitsubishi Pajero

1 Answer

How to change a cranshaft sensor of a pajero junior


this should be your pajero jr
crankshaft angle sensor

not to be confused with the camshaft angle sensor

harmonic balancer off
timing cover off
timing belt can stay on
25753547-bj3qxddo4jve3nf3q1tohv1n-1-0.pngchange-cranshaft-sensor-pajero-junior-bj3qxddo4jve3nf3q1tohv1n-1-2.jpg

Jun 20, 2015 | Mitsubishi Pajero Cars & Trucks

1 Answer

Where can I find the crank sensor on a 2009 Nissan Titan v8 truck?


i think it's the starter. On most nissans, the starter and the crank position sensor are close to each other. Some nissans have 4 position sensors, between crank sensor, crank angle sensor, cam position sensor, and sensor sensing sensor, oh and cam angle sensor. Oh wait, maybe it's a bad ground. Nope, gotta be the staerter.
25440212-xipalmoknr3fbjmp51kycajc-3-0.jpg

25440212-xipalmoknr3fbjmp51kycajc-3-1.jpg

Feb 17, 2015 | Nissan Cars & Trucks

1 Answer

Where does the crank angle sensor go on a 1990 dodge daytona es turbo and what does it do


crank angle sensor, Crank position sensor ,reads the position in degrees of the crankshaft. When the sensor reads a set point on the crankshaft it sends a signal to the ECM(CPU) program which then triggers the spark for that positioned cylinder. It also triggers the injector to squirt. Without it the CPU will not know when to set the spark or injector so nothing works.It is constant for all ECM controlled engines regardless. Further the cam shaft position sensor sends a signal to the cpu telling it that the valves are in the correct position for spark,fuel. When the cam belt/chain breaks there is no position regestired so the spark and fuel are shut off

Dec 05, 2014 | 1990 Dodge Daytona

1 Answer

Location of cam and crank angle sensor in 96 N15


The cam and crank position sensor can be found in the front of the crank on the engine block below or next to the water pump in many applications.
It can also be located on the main crank pully or the flywheel.

Feb 09, 2012 | Nissan Pulsar Cars & Trucks

1 Answer

Car stopped while driving. Tried to start it , but to o avail. Turns over , but no spark. Changed coil changed distributor changed rotor and still nothing. Any ideas?


Hi, you will need a voltmeter to diagnose the problem. Set your meter to DC, turn the key on, and check the voltage at the positive coil terminal (black wire with white stripe) with the other probe at engine ground. If no battery voltage, suspect your ignition switch or fuse. If you have battery voltage to the coil, next set your meter to AC and check voltage across the coil primary winding (black wire with white stripe and other black wire) while someone cranks the engine. You should have at least 1 volt AC or more. If no AC voltage, suspect your crank angle sensor inside the distributor. The distributor would have to be replaced, so you would want to be sure it's bad. There are some specific tests you could run, but I would need to know the exact engine you have to provide correct test procedures.

jturcotte_1696.gif


TESTING

E16i, CA16DE and CA18DE Engines
See Figures 1, 2 and 3


0900c152801ce40b.jpg

Fig. Fig. 1: Crank angle sensor testing terminals-CA16DE engine


0900c152801ce40c.jpg

Fig. Fig. 2: Crank angle sensor testing-E16i engine


0900c152801ce40d.jpg

Fig. Fig. 3: Crank angle sensor testing-CA18DE engine

  1. Disconnect the CMP electrical connector.
  2. Turn the ignition switch to the ON position.
  3. Using a voltmeter and check the CMP power source between terminal B and a known good engine ground. The voltmeter should read approximately battery voltage.

    If reading is as specified, proceed to the next step. If reading is not as specified, check power supply circuitry.

  1. Turn the ignition switch to the OFF position.
  2. Using an ohmmeter, check the CMP sensor ground circuit, by connecting the meter between a known good engine ground and terminal:

    E16i engine- terminal D . CA16DE and CA18DE engines- terminal A .

  1. Continuity should exist.

    If continuity does not exist, repair open in ground circuit. If continuity does exist, proceed to the next step.
  2. Start the engine.
  3. To test the sensor 180° signal, connect a logic probe between the following terminals:

    E16i and CA18DE engines-ECU terminal 17 and a known good engine ground. CA18DE engine-ECU terminals 21, 31 and a known good engine ground.

  1. To test the sensor 1° signal, connect a logic probe between the following terminals:

    E16i and CA18DE engines-ECU terminal 8 and a known good engine ground. CA18DE engine-ECU terminals 22, 32 and a known good engine ground.

  1. The logic probe should indicate that a pulse signal exists in both tests. If a pulse signal was not present, inspect wiring. If wiring is okay, replace the crank angle sensor.

May 21, 2011 | 1987 Nissan Pulsar

1 Answer

How do i replace the crank position sensor on a 2000 jeep grand cherokee


If you have the type of crank angle sensor shown in the image, then it will be located on the bell-housing towards the top of the bell-housing and usually on the drivers side. Dis-connect the faulty crank angle sensor and then un-bolt the two bolts that secure the crank angle sensor to the bell-housing and then remove the sensor. The best access to the crank angle sensor is from under the vehicle.


47ada7e.jpg

Jun 21, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Ceased kick down on Mitsi Pajero 1990. Not an


my kick down cable in my v44 pajero has my foot pedal hard what can i do

Jan 16, 2010 | 1990 Mitsubishi Montero

1 Answer

Jeep wrangelr Crank Position Sensor


wall5552: there were two engines used in 1992 Jeep Wranglers.
A 2.5 liter and a 4.0 liter. HOWEVER>>>> The location for the crank angle sensor is the same for both.
It is located on the bell housing up near the front at about the 10:00 PM position.
The Cam position sensor is located in the Distributor on both engines as well.

May 10, 2009 | 1992 Jeep Wrangler

1 Answer

Check engine light is on


remove positive battery for five minutes to re set the computre hook it back it should go out

Jan 05, 2009 | Hyundai Motor 2004 Sonata

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...