Question about Chrysler 300M

Open Question

Dtc code po344 - 300M Chrysler Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I took my car to Auto zone and they read a 344 code


TYPE: OBD PO344

Keep in mind that codes are used to diagnose
systems & component test,to find a problem

They have nothing to do with the need to install parts

Sep 30, 2014 | 2004 Chrysler Concorde

2 Answers

Eng starts hard,runs good until the rpm is over 2200 then it stumbles my input voltage on the cam sensor is 5volts ,on most cars i've read should have 8volts where


Both crank and cam sensors have a 8 volt reference I have found the wiring melted together where it cross over transmission shorting out the signal. also test your reference voltage at the computer with circuit unplugged at sensor watch meter and wiggle wiring going back to computer this will help find faulty area.

Nov 07, 2013 | 2005 Chrysler Sebring Conv

1 Answer

How do i fix a problem with a PO344 code


You'll need to have someone diagnose the problem first. Code 344 is for an intermittent problem with the cam sensor on bank one.
The sensor and wiring would need to be checked.

Aug 08, 2013 | 2004 Chrysler Sebring Convertible

1 Answer

2004 dodge stratus 2.4 dohc po344 code


PO 340 thru PO344 are cam shaft position sensor issues

That does not tell you what is wrong or to replace anything

Have it diagnosed at a repair shop

A sensor could fail & it more than likely is just
reporting other issues you have to have resolved.

Oct 02, 2012 | 2004 Dodge Stratus

1 Answer

What does PO344 mean


Code PO344: Rationality error detected for intermittent loss of camshaft position sensor circuit

A problem with either your cam/camshaft sensor.

Apr 30, 2012 | 2006 Dodge Durango

1 Answer

I have engine code PO344 on myy durango 5.9 litre


sounds like an o2 sensor google the code !

Nov 24, 2010 | 2000 Dodge Durango

1 Answer

Have2004 intrepid shows engine light and error codes po340-& po344


code po 340 no camshaft position sensor signal at powertrain control module and code po344 rationality error detected for intermittent loss of camshaft position sensor circuit. hope this will help you!!!!

Apr 18, 2010 | 2004 Dodge Intrepid

3 Answers

How can i fix code po344 intrepid 2002


Before replacing the cam shaft sensor,verify good terminal tension and connection at the sensor.This carline has a history of faulty connections here and this could fixya before spending the cash on car parts....good luck

Jul 24, 2009 | 2004 Dodge Intrepid

1 Answer

I'm getting the engine light coming every so often. It seems that after I fill the tank and get down around 3/4 tank, The message I'm getting is "EVAP Emission Control System Purge Flow Fault". PO441 and...


I have a 2004 dodge stratus 2.4 dual overhead cam. When driving down the road, bell goes off, check engine light comes on, and it's like I'm driving on limp mode, when going over 2000 rpm's, there's a severe stutter. After getting code for light it points to cam shaft sensor, which i changed. I also changed crank shaft sensor. After all of this was done, drove great for about 30 miles and the same thing happened all over again. If anyone can point me in the right direction it would be greatly appreciated.

Jul 05, 2009 | 2004 Dodge Stratus

1 Answer

Po340 and po344 intrepid


Take a look at this link http://www.obd-codes.com/p0340.  The problem lies in the cam shaft sensor circuit which means that it isn't necessarily the sensor itself.  Read what that page has to say and just start from the top and work your way down the solutions.  As far as how much it cost, it obviously depends on what is wrong, but assuming it is your cam shaft sensor you can buy the part for around forty dollars at AutoZone.  Let me know if you have any other questions.  Thanks for rating my response and for using FixYa!

May 29, 2009 | 2004 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...