Question about Ford Cars & Trucks

1 Answer

2000 ford ranger, 6cyl, 4x4,5spd manual trans, the speedometer spins crazy fast.. i disconnected the sensor in the rear & it still spins fast..???

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

THE TRANSDUCER IN THE GEARBOX IS FAULTY
THE GEARS ARE NYLON AND ARE PROBABLY WORN AND SLIPPING EASY FIX

Posted on Oct 22, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: speedometer guit working on my 2000 Ford Ranger ,standard trans.

Need New Speedometer

Posted on Jun 11, 2008

the recycler
  • 22 Answers

SOURCE: need location of the erg sensor 2000 ford ranger

The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Posted on Feb 25, 2009

the recycler
  • 22 Answers

SOURCE: location of the egr sensor on 2000 ford ranger

The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Posted on Feb 27, 2009

Hightower971
  • 183 Answers

SOURCE: accelerating from a stop at b/t 30-35mph transmition hesitates

Your transmission is going out, sorry to be the bearer of bad news dude. You have an internal pressure leak. That's why it's catching and releasing. You have to build up the pressure in it to get it to engage the clutchplates. Everytime it does that, you're getting closer and closer to it not going back into gear. Park it if you can, otherwise you will be towing it in a couple of weeks if driven every day.

Posted on Apr 23, 2009

  • 534 Answers

SOURCE: left rear turn signal quit on 2000 ford ranger.

Check correct wattage globe is installed in both front and rear indicator lights;
check if any other side/repeat indicator lights have failed.

Posted on Jun 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changed my 1997 ranger from automatic to manual now i dont have a speedodometer


there should be 3 plugs on your manual trans one is reverse lights idk what the other two are there is also one on the rear differential i believe that one is the speedometer

Nov 18, 2012 | 1997 Ford Ranger SuperCab

1 Answer

Hi. My ford escort 97 lx wagon transmission is not shifting anymore it is stuck in first gear(althought if i put it in neutral while driving and switch back to drive it picks up for a few seconds...) and...


My brothers 2000 ford ranger the fuse went out to the speed sensor. I change the speed sensor because it did not shift out of 1st gear and the speedometer stopped working. I then found out the fuse was missing in the fuse panel. My brother could not tell where the fuse went but when I put a fuse in it started shifting and the speedometer started working. everything was good. You should have a code if it is the speed sensor.

Aug 14, 2017 | Ford Escort Cars & Trucks

2 Answers

2000 ford ranger with 3.0 eng. and stick shift, while driving my speedometer quit at the same time my abs brake warning came on. the speedometer starts working after i getup to about 55 or 60 mph any ideas...


Check ABS tone rings and sensors at wheels. Speedometer may be using these signal too. Visually verify rings (look like gears around axles) are intact with all teeth and sensors are at rings with connector attached. Troubleshooting the ABS system is beyond my skill level. If no joy on visual inspection, maybe one of the other experts can chime in on troubleshooting ABS.

Sep 09, 2010 | 2000 Ford Ranger SuperCab

2 Answers

Where is the vss located on a 95 ford windstar. The speedometer went ouit and its shifting crazy.


The vehicle speed sensor is located on transaxle in behind the engine.
Tricky to get at and not an easy replacement.
While it is possible the sensor is bad, the more common issue with your Windstar is the speedometer itself.
You should have it properly diagnosed before replacing parts.
If the speedometer is the defect you will need to replace the instrument panel as an assembly.
Using parts from a recycler will often result with another bad speedometer as it is a very common problem.
Some aftermarket auto supply may be able to get you a rebuilt unit.
if not you may have to get it from Ford.

Jul 29, 2010 | Ford Windstar Cars & Trucks

3 Answers

2000 Ford Ranger XLT electrical problem


Check your rear end to see if you have a sensor like in this video, if so it could solve some issues. The video describes items all going out around the same time. Its based on a 2 wheel drive but who knows you might have the same sensor in the same location. This is a shot in the dark, but who knows it might help or point you in the right direction.

Nov 04, 2009 | 2000 Ford Ranger SuperCab

1 Answer

2000 Ford Ranger XLT Automatic trans. 4X4 3.0L


Check your operator's manual. Make sure any and all fuses that have anything to do with the affected items are not blown and are working properly. If you can; check for loose fuse connections or wires. Hope this helps. God bless!

Nov 04, 2009 | 2000 Ford Ranger SuperCab

2 Answers

Accelerating from a stop at b/t 30-35mph transmition hesitates


Bolted onto the Transmission housing.

639b63f.jpg
Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question

Apr 23, 2009 | 1999 Ford Ranger SuperCab

1 Answer

Where is the auto trans fluid stick at?


Passenger side of engine at very rear of engine

Oct 21, 2008 | 1987 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...