Question about 2002 Mazda 626

1 Answer

My 2000 mazda 626 has lost all coolant but has not overheated

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 174 Answers

Loosing coolant may trick the water sensor(will not show temperature as is not merged in water.The apearence of loosing all coolant also may be tricky,the coolant will stay at a lower level,mistaken as no coolant,as long as more than 50% of the cilynder is merged in water it will allow to cool down as u dont force it.

Posted on Oct 22, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Mazda 626

Hi Janieanip01,
Again we need more imfo....Is the vehicle injection?....If it is you'll have to wait until the fuel rail is re-pressurised before it will start....Crank it for about ten seconds at a time so as not to burn out the starter motor....It may be that the vehicle didn't run out of fuel but instead the pump may have given in....and when did you last replace the fuel fiter?
Regards Johngee10

Posted on Aug 10, 2008

  • 1 Answer

SOURCE: 1995 mazda 626 overheating

this appears to be a common problem with 626s. Assuming you have done the normal things: checked the coolant & thermostat the big culprits are the electric fans not coming on & the radiator being too small to provide any leaway if it gets clogged. make sure there are no leaves etc blocking it but it probably is scale build up inside.

Also be sure to check the overflow tank for cracks - they do that a lot particularly if they over heat

Posted on Oct 24, 2008

CRTN
  • 716 Answers

SOURCE: changing the tail light bulbs on a 2000 mazda 626

The Tail Lights Are Accessed From The Inside Of The Trunk There Will Either Be A Panel Immediately Behind Where The Light Is Or Carpet. Remove It And It Will Give You Access To The Rear Of The Bolts Just Grab Twist And Pull And The Light Will Come Out.

Posted on Jan 26, 2009

  • 39 Answers

SOURCE: 98 Mazda 626 overheating. Blew off hose and was

Yes, this is most likely a thermostat problem.

As a basic explanation, the thermostat is the device which separates the hot coolant in the engine block from the cool coolant in your radiator. If it gets stuck closed, your radiator coolant will remain at near room temperature, while the coolant in your block (which is what your gauge reads) does not circulate and will skyrocket in temperature.

Posted on Aug 13, 2009

Testimonial: "Very helpful. Discription makes sense/logical explanation of symptoms."

bschilz
  • 2049 Answers

SOURCE: what is the oil capacity of a mazda 626 LX

2.0L - 3.7 quarts.
2.5L - 4.2 quarts.

Posted on Nov 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 Mazda 626


You cook it good, You will be lucky if it will start back up,

Dec 06, 2012 | 1997 Mazda 626

1 Answer

2000 mazda 626 wont blow cold air i have replaced compressor dryer and flushed the system and reinstalled new freon any ideas


There is a valve that stops hot coolant from entering the heater box. It is probably stuck open. murf427

Aug 29, 2012 | 2000 Mazda 626

1 Answer

My mazda 626 is pouring coolant out of the overflow hose. Not overheating. Not sure if temp gauge is working.


Ask a local mechanic to diagnose for you as this could be a thermostat problem but it could also be a head gasket but another problem could be the water pump impeller the plastic impeller comes adrift from the metal drive shaft

Feb 27, 2012 | 2002 Mazda 626

1 Answer

My 2002 mazda 626 was overheating. Replaced the radiator (cracked) and coolant tank (leaking). Still overheating. Its the thermostat or the water pump right? Which should I check first? Where how and what...


I would check the thermostat. It should be in the housing that the upper radiator hose connects to. I would take the thermostat and put it in a pan of water on a stove, if the thermostat doesn't start to open before the water begins a rolling boil, the thermostat is probably stuck closed.

Oct 27, 2010 | 2002 Mazda 626

1 Answer

Overheating mazda 626 1989 model how do i know if


CHECK COOLANT LEVEL.IF COOLANT LEVEL OKAY A FAULTY.THERMOSTAT COULD BE THE POSSIBLE CAUSE.

May 04, 2010 | 1989 Mazda 626

2 Answers

98 Mazda 626 overheating. Blew off hose and was


it's either a bad thermostat or a leaking head gasket

Aug 13, 2009 | 1992 Mazda 626

Not finding what you are looking for?
2002 Mazda 626 Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...