Question about 2002 Toyota Sienna

Open Question

Hi I need solution to a toyota crown GRS 182 is

Hi I need solution to a toyota crown GRS 182 is showing ENGINE CHECK LIGHT,ABS PS,and AFS lights

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: check engine light/2003 toyota CE

your car engine may have some hidden problem, suggest you take it to dealer workshop to have you car ECU scan and it will resolve the problem once and for all.

Posted on Oct 15, 2008

jmassengill
  • 345 Answers

SOURCE: obd code p0440 for check engine light on 2000 Toyota Corolla

p0440 code means that the evap system has a leak. This could be caused by a bad or improperly installed gas cap. Either that or the purge solenoid has failed or the canister is plugged and not working properly.

Posted on Nov 15, 2008

mecanica03
  • 874 Answers

SOURCE: My 2007 Toyota Tundra 4.7l shows VSC OFF lights

check air filter for dirty , how many miles or kms have your car? , maybe need to replace spark plugs, try to reset the ecu for a momentany malfunction, remove the negative battery terminal few minutes and reconnect,start engine and drive, check if lights goes off , please write me

Posted on Jul 05, 2009

Mark Steele
  • 6 Answers

SOURCE: ABS light is on and Track-Off light is blinking

"ABS light came on and Track-off light started blinking"
This happened after I replaced the rear struts (shock absorbers") It turned out to be the left rear wheel sensor ($156.75). I must have damaged it when I replaced the strut. The way to check the 'rear' sensors is to remove the back seat to gain access to each sensor plug (2 prongs). Unplug it and check for continuity. If there is no continuity then you have a bad sensor, or an unlikely break in one of the wires. I checked for a break in each wire but they were fine.

Posted on Oct 01, 2009

  • 2 Answers

SOURCE: 2006 Toyota RAV4, 3.5L V6 Check engine

I am having a multiple cylinder misfire on my 2006 Toyota RAV4 with the 3.5L V6. Every cylinder is reporting a mifire. Each cylinder has it's own coil. I highly doubt that all 6 coils went bad at once. Does anyone have any idea what my be causing this?? Is that the problem you two are having?

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a 2004 toyota 4runner my check engine light, VSC light and my Trac Off light all came on at the same time, what is most commonly the cause?


The VSC and Traction system are basically using the ABS to work. The most common issue is a failure of one of the wheel sensors for ABS. Would think the engine light will probably turn out to be for ABS failure code. Most auto parts stores, and some shops will read codes for no charge - so take it and see if the code does show as a failure in ABS system. Some code readers can not read the actual ABS computer to give you a detailed code of what is causing the issue - but if you can read detailed code it may lead you to exact issue.

Mar 04, 2015 | 2004 Toyota 4Runner SR5

2 Answers

Abs actuator toyota


Remove the front wheels and inspect the ABS connector wires that run above the control arm. Chances are you will find that these wires are damaged.The ABS is in or around the wheel bearing and there is a clip that can be gently pried back to remove the ABS plug from the Wheel bearing sensor or the external sensor in that area.
Sometimes a faulty alternator will light up the ABS sensor light. Check to see if the vehicle is charging when this light is on., typical voltages while the car is on should be around 12.5 to 14 volts. You can test it right at the battery while the car is running.
Sometimes an alternator will only go faulty once the component inside get hot.
Typically the wires to the Wheel Hub sensor goes bad from exposure to the elements, especially snow and ice climates or rocks and dirt-roads a lot or if you go through bushes a lot.

Jan 21, 2014 | Toyota Corolla Cars & Trucks

3 Answers

How to reset check engine light warning


normally to reset a check engine light all you have to do is unhook the battery for a couple of minutes and then hook it back up. if you are having a sensor problem though this check engine light will come back on after you drive the vehicle for more than 3 minutes.

Jan 29, 2013 | 2002 Toyota Sienna

1 Answer

Toyota Pasoo ABS light is not turning off. Hi, i have recently bought Toyota Pasoo 2007 (reconditioned japan) and now its ABS light is not turning off even i have checked the break oil level which shows...


The ABS light will not set because of fluid level the red brake light will. Usually an ABS light is set because either the solenoid is faulty, BCM (Body control module) is not functioning properly(not to likely) or there is excessive wear to the brake pads. Solenoid and or BCM can be simply one of the ABS Fuse's. There is one in the engine compartment fuse box and one in the fuse box contained withinor below the dash panel on the drivers side.

Aug 23, 2012 | Cars & Trucks

2 Answers

I repleaced all 4 abs sensor on my 1996 toyota avalon, but the abs light still on, what could be the problem?


abs light on means some fault codes stored in your car,
toyota it2 can help you clear the code and turn off the light with airbag.

May 16, 2012 | 1996 Toyota Avalon

1 Answer

I have a toyota nze it has aproblem of showing hand brake light and abc.please help.


Hi there!

The brake light is always an indication of low fluid level or low pressure in the fluid system. The ABS light comes on when a problem detected with one of the 4 sensors or wires that connect the sensors to PCM in your vehicle. So what you can do is check the fluid level and about the ABS you will need to scan it to see whats the code that was stored. Good luck

Jul 16, 2011 | 2002 Toyota Corolla

1 Answer

ABS light show problem free Solution


Hi:
The ABS light is telling you that your Anti Lock Brake sytem is not working, due to a malfunction. Usually this is caused by a wheel speed sensor, but you need to download your car's codes to find out for sure. Most auto parts stores will do this for you free of charge.
You will still have your normal braking system, but it should be a good idea to check your brake fluid level to make sure you have no leaks.

Mar 18, 2010 | 2005 Toyota Corolla

2 Answers

Toyota Tundra 2005. ABS, Airbag, Tire & cruise dash lights flash


how do you turn the maintenance light off after making oil change?

Mar 09, 2009 | 2006 Toyota Tundra

1 Answer

Desh meter lights


Regarding the corolla abs light, you need to get your local dealer to diagnose the fault, it is possible a wheel sensor giving a faulty reading but while the abs light remains on you have no abs. Worth getting it looked at promptly

Jul 29, 2008 | 2006 Toyota Corolla

Not finding what you are looking for?
2002 Toyota Sienna Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...