Question about Cars & Trucks

Open Question

How to remove the rear bumper bar for ford territory

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Removing rear bumper on Audi A4 1997 to fit tow bar

Did you get the solution to this, I have the same problem

Posted on Jul 14, 2008

Ad
  • 99 Answers

SOURCE: Remove rear plastic bumper cover

please email me at meanness628@aim.com with any other info or questions if you have already gone to a body shop

Posted on Sep 29, 2008

mikehitchner
  • 28 Answers

SOURCE: how difficult is it to remove the rear bumper on a Ford Explorer

its not the bumper

Posted on Jan 01, 2010

  • 92 Answers

SOURCE: I have a 2006 Ford Explorer and 2 of my park aid

You only need to remove the bumper cover. Remove both tail lamp assemblies. Under the tail lamps you will a 10mm and a 8mm bolt, remove these. Look into each rear wheel well rearward and you will find a T20 torx screw on both sides, remove these. On the top of the rear bumper, between the bumper and the bottom of the liftgate opening you will find 6 to 8 plastic rivets that can be removed by pulling the center pins out, remove these. At this point you should be able to lift upward and rearward and release the bumper cover. Once the cover is free you must disconnect the electrical connector to the sensor wiring harness. With the bumper cover on the ground or a bench, you will see 4 9/16" nuts that hold the styrofoam bumper cushion to the bumper cover, remove these. Now you should be at the point where the backup sensors are accessable. When you install the new sensors be sure your electrical connectors click when they connect. these connectors go on hard and if they don't click you will be doing this job again. Reassemble in reverse order.
Hope this helps

Posted on Apr 03, 2010

  • 4793 Answers

SOURCE: Volkswagen Passat rear bumper removal

all the screws/bolts are underneath the plastic cover.hex head.(allen key)

Posted on Jul 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's the towing eye cover?


I have already explained this in another question. The cover is a small panel on the front and back bumper bar that the towing eye screws into It usually just clips into the bumper bar..

Feb 27, 2016 | 2008 Ford Territory 4.0

2 Answers

2008 ford escape. removal of rear bumper cover


Pop the Hatchback open and remove the connectors
from the top of the bumper cover.

Optional Step: Using a Floor Jack, raise both sides
of the car in the back, supporting both sides with
jack stands, and remove the rear wheels.

Using Torx Bits, remove the inner rear wheel well
lining.

Get behind the rear wheel well and loosen the bolts
holding the bumper brackets on. They're pretty
difficult to find and remove. Be Patient. Do the
same to the other side.

Remove the rear bumper cover by pulling the cover
outward from the part nearest the wheel on both
sides. Once removed, take off the 2 black mounting
brackets from the bumper cover.

Good Luck

Feb 27, 2015 | 2008 Ford Escape

1 Answer

Ford territory rotor removal


front or rear wheel to different proceedure's

Feb 19, 2015 | 2006 Ford Territory 4.0

1 Answer

Does anyone have any useful information on how to remove front bar cover on a 08 Ford Territory.


I haven't done a Territory, but. There are bolts underneath at the fenders where the bumper meets them, you have to remove the grill (just pops off) and get the plugs out behind it. You will also have to remove bolts and plugs from the bottom of the bumper.

Nov 14, 2014 | Ford Territory Cars & Trucks

1 Answer

How to removing the rear bumper bar


Slide under the bumper and look on the back side of it. You will find the bolts that attach it to the body.

Aug 07, 2014 | 1999 Saab 9-5

2 Answers

How to remove rear bumper 1999 blazer


Hi there:
Check this Removal Procedure...

6_23_2012_11_21_59_pm.gif

1. Remove the rear bumper step pads.
2. Remove the license plate lamps.
3. Remove the nuts and the bolts that retain the rear bumper impact bar to the bumper bracket.
4. Remove the rear bumper impact bar from the vehicle.

Installation Procedure

6_23_2012_11_22_56_pm.gif

Notice: Refer to Fastener Notice in Service Precautions.

1. Install the rear bumper impact bar to the vehicle as follows:

1.1. Position the bumper impact bar on the bumper brackets so that the holes in the impact bar are aligned with the bracket holes.
1.2. Install 2 bolt plates and 4 nuts on top of the impact bar.
1.3. Install 2 bolt and nuts through the bottom of the impact bar. Tighten the rear bumper impact bar nuts to 90 N.m (66 lb ft).

2. Install the license plate lamps.
3. Install the rear bumper step pads.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 23, 2012 | 1999 Chevrolet Blazer

1 Answer

How to take off a spare tire off an expedition


Under the hood there is a long turning bar attached. Remove the bar and proceed to the rear of the vehicle. Open the rear door and locate a hole near the rear bumper, insert tapered end of bar in hole and align with slight turning motion until you feel a resistance. Rotate bar counterclockwise in which this will start to lower the spare tire from underneth the rear of the vehicle.

Hope I gave adequate instructions.

Eric.

ebnyprnce@yahoo.com

Dec 26, 2010 | 2000 Ford Expedition

1 Answer

Need to remove rear bumper from 2001 ford explorer


easier to remove the frame bolts from the brackets and remove the entire assembly and place it on a set of hourses to remove the face bar separately. bodymen do it this way all the time for it is the easiest way to do it

Sep 04, 2010 | 2001 Ford Explorer

1 Answer

Fit NUDGE bar to Ford Territory


I wish to fit nudge bar to my territory, is there an instruction manual available

Jan 07, 2010 | Ford Bronco Cars & Trucks

1 Answer

How to Remove the Rear Bumper - BA Fairmont/Falcon


Firstly, you need to remove the rear splash shields from within the rear wheel arches and also the tail lights. Then remove the scrivets from the lover edge of the bar. Next remove the scuff plate at the boot opening and fold the carpet back. There are four nuts which hold the bar on, undo these and then lift the sides of the bar up and pull out. The bar has large clips on the side which hold it in place.

Aug 04, 2009 | Ford Fairmont Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

533 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...