Question about Cars & Trucks

Open Question

Screen geometry oo sansui B2B 29 inch crt flat tv problem

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

04 toyota 4 runner steering is all new and now it seems to be tight in the center position while driving?


but is the geometry correct, just because these have been replaced does not mean that the geometry is correct. Any mechanic can replace the parts but the geometry has to be set correctly by a steering specialist. Need to check camber, caster toe in/out

May 28, 2015 | 2004 Toyota 4Runner

1 Answer

My package has not yet arrived promided by 12/29/14


Your gonna want to contact the folks that you purchased your package from. There is literally nothing we can do for you.

Jan 07, 2015 | Cars & Trucks

1 Answer

1988 BMW 528 E. plz inform cost of waterpump and timing belt


Here in Georgia, from O'Reilly's auto parts The water pump will cost, $45.oo to $65.oo. depends on which one you want or which warranty. The timing belt $16.oo to $35.oo. O'Reilly's Auto Parts.

Feb 16, 2011 | 2000 Volkswagen Golf

1 Answer

Front tire inside shoulder wear. Have to replace tires every 6 months. You can't adjust alignment (except tow). Been doing this since new. Common problem I hear.


had the same problem with my 87 86 merc cougars the 14 in tires where not designed for the geometry of caster/toe/ ste up .....i simply put 15 inch 70 rims and tires problem went away and the car handled great.

Oct 30, 2010 | 2006 Jaguar X-Type

1 Answer

Do you have to drop the fuel tank down to remove the fuel pump?


Yes, the pump is mounted inside the tank, will cost you about $270.oo to $320.oo new. Looks like this -->>> 3b3adcd.jpg

Oct 10, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

I need to know the fuel pressure on oo isuzo


FUEL PRESSURE IS 48 - 55 PSI. IF FUEL PRESSURE LOW REPLACE FUEL FILTER FIRST BEFORE BUYING A NEW FUEL PUMP.

Jul 14, 2010 | 2002 Isuzu Trooper

1 Answer

ANY INFO ON HOW TO LIFT 1985 CHEVY C-10 TRUCK WITHOUT USEING A LIFT KIT.MOST SIMPLE WAY AND CHEAPEST


The rear is easy, it can be lifted with blocks placed between the rear axle and the spring. Without the proper wedge shaped spacer the driveshaft angle will be incorrect if you use a block bigger than 2 inches. There is no way I know to lift the front, and keep the suspension geometry proper for tire wear, and driveability. Short answer: get a lift kit designed for your truck, you will avoid alot of headache later.

Jun 15, 2010 | 1985 Chevrolet Chevy

1 Answer

What is the torque settings on the head bolts for 2002 nissan x-terra 2.4litre?


① Step 1: 22 ft. lbs. Step 2: 59 ft. lbs. Step 3: Loosen completely then retorque to 22 ft. lbs. Step 4: 18-25 ft. lbs. Step 5: Plus 86-91 degrees ② 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs. ③ The cylinder heads and the lower intake manifold are installed together Step 1: Tighten the cylinder head bolts to 22 ft. lbs. Step 2: Tighten the cylinder head bolts to 43 ft. lbs. Step 3: Loosen the cylinder head bolts completely Step 4: Tighten the cylinder head bolts to 84 inch lbs. Step 5: Tighten the intake manifold fasteners to 35 inch lbs. Step 6: Tighten the intake manifold fasteners to 13 ft. lbs. Step 7: Tighten the intake manifold fasteners to 12-14 ft. lbs. Step 8: Loosen all intake manifold fasteners completely Step 9: Tighten the cylinder head bolts to 22 ft. lbs. Step 10: Tighten the cylinder head bolts 60-65 degrees Step 11: Tighten the cylinder head sub-bolts to 80-105 inch lbs. Step 12: Tighten the intake manifold fasteners to 35 inch lbs. Step 13: Tighten the intake manifold fasteners to 78 inch lbs. Step 14: Tighten the intake manifold fasteners to 70-84 inch lbs. ④ 10-12 ft. lbs. +60-65 degrees ⑤ Step 1: 72 ft. lbs. Step 2: loosen completely to 0 ft. lbs. Step 3: 29 ft. lbs. Step 4: Plus 75 degrees clockwise Step 5: Plus 75 degrees clockwise ⑥ Step 1: bolts 11-22 19 ft. lbs. Step 2: bolts 1-10 29 ft. lbs. Step 3: bolts 1-10 Plus 60-65 degrees ⑦ Step 1: 20 ft. lbs. Step 2: loosen to 0 ft. lbs. Step 3: 14 ft. lbs. Step 4: Plus 85-95 degrees ⑧ Step 1: 31 ft. lbs. Step 2: Plus 60 degrees ⑨ 83 inch lbs. ⑩ Stud bolt: 11 ft. lbs. Nuts: 31 ft. lbs. ⑪ Step 1: 72 ft. lbs. Step 2: loosen completely to 0 ft. lbs. Step 3: 29 ft. lbs. Step 4: Plus 90 degrees clockwise Step 5: Plus 90 degrees clockwise ⑫ Bolts: 17-24 (M8) 16 ft. lbs. Install rear main seal Bolts: 1-16 (M10) 26 ft. lbs. Bolts: 1-16 (M10) Plus 90 degrees clockwise ⑬ Step 1: 33 ft. lbs. Step 2: Plus 84-90 degrees clockwise ⑭ Intake manifold collector: Bolts and nuts: 8 ft. lbs. Stud bolts: 61 inch lbs. ⑮ Intake manifold: Bolts and nuts: 5 ft. lbs. and than to 21 ft. lbs. Studs: 8 ft. lbs.

Jan 10, 2010 | 2002 Nissan Xterra

1 Answer

I have a Samsung TV, it flat lined


needs fixing, or replacing, sorry!

Dec 01, 2009 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...